B-K lighting HP2 SERIES User manual

Warning High Voltage Hot Surface
NEEDED
FOR
INSTALLATION:
HydroLock Plate
Waterproof
Wire Connectors
O-Ring
HP2 Housing
Stability Flange
Concrete Pour
Collar (CPC)
HP2
Deep Housing - Standard MR16
Quick
Disconnect OptiLock
Assembly
Faceplate
Thumbscrew
Optional Accessory
Holder
Retaining Clip
· Suitable for wet locations · Suitable for recessed in ground locations
IMPORTANT LISTINGS AND CERTIFICATIONS
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel with appropriate personal protective
equipment must perform all servicing of this product.
• Before wiring to power supply and during servicing, turn off and
lock out power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL
SAFETY AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part,
as this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body.
• Replace LED assembly only with correct wattage and type
of power supply appropriate for LED assembly.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause
an unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY
TO PERSONS IMPORTANT
SAFETY INSTRUCTIONS
Lighted fixture is HOT!
WARNING - To reduce the risk of
FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing LED.
Fixture gets HOT quickly! Contact only switch/plug when
turning on. Do not touch hot lens, guard, or enclosure.
Keep fixture away from materials that may burn.
Do not operate the luminaire fitting with a missing or
damaged shield. Do not touch the source at any time.
Use a soft cloth or gloves. Oil from skin may cause
damage.
SAVE THESE INSTRUCTIONS
Soil Prep
Conduit
trench 18”
Dia.
A. Determine Soil Type by referencing
DIG-IT Guide.
B. Dig hole 18” wide and 20” deep.
Conduit
Trench
Excavated
for Housing
C. Prep soil according to DIG-IT Guide.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION
INSTRUCTIONS
RELEASE DATE
10/06/2021
REFERENCE NUMBER
INS-1344-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR
SELL ANYTHING IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
Remote Transformer Installation Instructions 1/8” Allen Wrench
Waterproof Wire Connectors
Level
Phillips Screwdriver
7/8” Hole Saw
Proper soil preparation is recommended before installation. See the DIG-IT guide at
www.bklighting.com/collaterals/install/digit.pdf for more information.

RELEASE DATE
10/06/2021
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
Housing Installation
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
2. Place housing in hole. Align junction box in
the path of the conduit trench.
3. Insert hour (4) pieces of ½” EMT conduit
through the Stability Flange. Hammer into
substrate until secure.
Leave sufficient clearance to elevate
housing to finished grade.
4. Raise housing on EMT so housing is flush
with finished grade. Use a level to aid in
housing installation.
5. When housing is level, tighten screws on
Stability Flange to secure housing to EMT.
Remove excess EMT as needed.
7. Per DIG-IT Guide, backfill the gap between
the bottom of housing and bottom of hole
with sand for drainage.
Flush with finished grade
6. Pull primary branch circuit wiring into
junction box.
8. For soil installation: Fill and tamp soil to
the appropriate height leaving room for sod,
pavers, etc. to be level with the top of the
temporary cover.
Soil installation is not drive-over rated.
9. For concrete installation: Fill the hole
around the fixture housing to 12” below the
finished grade with clean fill dirt and tamp
carefully to prevent settling of fixture. Pour
concrete and finish as required flush with the
top surface of the temporary cover.
REFERENCE NUMBER
INS-1344-00
HP2
Deep Housing - Standard MR16
Remote Transformer Installation Instructions
Threaded Entry
Side Flats
1. Connect branch conduit connectors (not
included) to the junction box using either the
threaded conduit entries on the bottom of the
junction box or through holes drilled into the
sides of the junction box.
Recommend 7/8” hole saw to open threaded
entry hole.

3. Wipe inside of housing where HydroLock plate
will sit clean of debris before inserting patented
HydroLock plate on to junction box. Align
HydroLock plate with pins in housing and seat
it firmly in place.
Installation
5. Connect optilock assembly to Patented
HydroLock Barrier plate with quick
disconnect.
WIRING DIAGRAM1. Remove temporary cover. 2. Make watertight connections using
waterproof wire connectors (provided) to
leads on the bottom of Patented HydroLock
Barrier Plate Assembly. See wiring diagram.
4. Turn HydroLock Barrier Plate clockwise ¼” to
lock.
Patented HydroLock Barrier Plate must be
completely seated to ensure proper seal or
water may intrude. This step must be done
as stated or you will void your warranty.
RELEASE DATE
10/06/2021
REFERENCE NUMBER
INS-1344-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
HOT (BLACK)
NEUTRAL (WHITE) HydroLock
Plate
GROUND (GREEN)
HP2
Deep Housing - Standard MR16
Remote Transformer Installation Instructions
6. Place OptiLock in HP2 housing and align
keyhole notch under one of (3) #8 screw heads.
Rotate horizontally to desired aiming position,
then tighten (2) #8 Phillips screws using Phillips
screwdriver. Install proper MR16 halogen lamp.
7. For Optional Accessory Holder: Insert
accessory holder tabs into slots on OptiLock.
8. Aim vertically by turning the thumbscrew on
OptiLock assembly.

9. Remove any dirt or debris in o-ring groove near
top of housing. Place o-ring inside of groove.
Failure to clean groove of debris will cause
fixture to fail and void product warranty.
10. Install faceplate using a 1/8” allen wrench and
hand-tighten the faceplate screws in a star
pattern to 30 in-lbs. min.
Do not use a power tool to install screws. Do
not exceed 40 in-lbs.
RELEASE DATE
10/06/2021
REFERENCE NUMBER
INS-1344-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
HP2
Deep Housing - Standard MR16
Remote Transformer Installation Instructions

Warning Hot Surface
TOOLS
NEEDED:
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all
Local and Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel must perform all servicing or relamping
of this product.
• Before wiring to power supply and during servicing or
relamping, turn off power at fuse or circuit breaker before
service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause
an unsafe condition. The use of damaged components may
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL
SAFETY AND INSTALLATION INSTRUCTIONS
cause an unsafe condition and void product warranty.
• Do not block light emanating from product in whole or part,
as this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time. Use
a clean, dry, soft cloth to handle the lamp. Oil from skin
may damage the lamp and cause it to rupture.
• Replace lamp only with correct wattage and type of lamp
marked on fixture label.
• All gaskets, O-rings and sealing surfaces must be kept
clean during installation and service; failure to do this may
cause an unsafe condition and void product warranty.
· Suitable for wet locations · Suitable for recessed in ground locations
IMPORTANT LISTINGS AND CERTIFICATIONS
1/8” Allen Wrench
1. Remove faceplate using a 1/8” allen wrench. If
there is an optional accessory holder, carefully
squeeze tabs on sides and gently pull from slots
on OptiLock.
2a. Firmly insert proper MR16 lamp into socket to
make connection.
Do not exceed the maximum wattage listed on
the fixture label before installing.
2b. Firmly insert proper ES16 lamp pins into socket,
then gently twist to make connection.
Do not exceed the maximum wattage listed on
the fixture label before installing.
Lamp Installation Or Re-Lamping if Required for MR16 / ES16 Lamp
MR16 Lamp Installation ES16 Lamp Installation
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY
TO PERSONS IMPORTANT
SAFETY INSTRUCTIONS
Lighted fixture is HOT!
WARNING - To reduce the risk of
FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing
lamp/LED. Lamp/ Fixture gets HOT quickly! Contact
only switch/plug when turning on. Do not touch
hot lens, guard, or enclosure (see diagram/picture).
Keep lamp/fixture away from materials that may burn.
Do not operate the luminaire fitting with a missing or
damaged shield. Do not touch the source at any time.
Use a soft cloth or gloves. Oil from skin may cause
damage lamp.
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION
INSTRUCTIONS
RELEASE DATE
10/06/2021
REFERENCE NUMBER
INS-1344-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR
SELL ANYTHING IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
HP2 & CO2
MR16 / ES16
Lamp and Accessory Holder Installation

HP2 & CO2
MR16 / ES16
1. Turn accessory holder upside down and remove
retainer clip. Insert up to (2) accessories.
Insert any accessory lens with the smooth side
towards the lamp. If using a honeycomb baffle,
position it farthest from the lamp.
2. Pinch retainer clip tabs and line up notches with
slots on accessory holder. Fit into accessory
holder to hold accessories in place.
6. Install faceplate using a 1/8” allen wrench and
hand-tighten the faceplate screws in a star
pattern to 30 in-lbs. min.
Do not use a power tool to install screws. Do
not exceed 40 in-lbs.
Optional Accessory Holder Installation for MR16 / ES16
3. Insert accessory holder tabs into slots on
OptiLock.
RELEASE DATE
10/06/2021
REFERENCE NUMBER
INS-1344-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
Lamp and Accessory Holder Installation
3. For Optional Accessory Holder: Insert
accessory holder tabs into slots on OptiLock.
4. Aim vertically by turning the thumbscrew on
OptiLock assembly.
5. Remove any dirt or debris in o-ring groove
near top of housing. Place o-ring inside of
groove.
Failure to clean groove of debris will cause
fixture to fail and void product warranty.

RELEASE DATE
10/06/2021
REFERENCE NUMBER
INS-1344-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR
SELL ANYTHING IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
1/8” & 7/64” Allen Wrench
Warning Hot Surface
NEEDED
FOR
INSTALLATION:
HP2
Faceplate Accessories
Accessories Installation Instructions
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all
Local and Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel must perform all servicing or relamping
of this product.
• Before wiring to power supply and during servicing or
relamping, turn off power at fuse or circuit breaker before
service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause
an unsafe condition. The use of damaged components may
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL
SAFETY AND INSTALLATION INSTRUCTIONS
cause an unsafe condition and void product warranty.
• Do not block light emanating from product in whole or part,
as this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time. Use
a clean, dry, soft cloth to handle the lamp. Oil from skin
may damage the lamp and cause it to rupture.
• Replace lamp only with correct wattage and type of lamp
marked on fixture label.
• All gaskets, o-rings and sealing surfaces must be kept
clean during installation and service; failure to do this may
cause an unsafe condition and void product warranty.
· Suitable for wet locations · Suitable for recessed in ground locations
IMPORTANT LISTINGS AND CERTIFICATIONS
Rock Guard with Optical Opening Rock Guard
For Use With:
Glare Shield B
Half Dome B
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION
INSTRUCTIONS
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY
TO PERSONS IMPORTANT
SAFETY INSTRUCTIONS
Lighted fixture is HOT!
WARNING - To reduce the risk of
FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing
lamp/LED. Lamp/ Fixture gets HOT quickly! Contact
only switch/plug when turning on. Do not touch
hot lens, guard, or enclosure (see diagram/picture).
Keep lamp/fixture away from materials that may burn.
Do not operate the luminaire fitting with a missing or
damaged shield. Do not touch the source at any time.
Use a soft cloth or gloves. Oil from skin may cause
damage.
SAVE THESE INSTRUCTIONS

RELEASE DATE
10/06/2021
REFERENCE NUMBER
INS-1344-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
Faceplate Accessories
HP2
Faceplate Accessories
Accessories Installation Instructions
3. Using a 7/64” allen wrench, loosen the (2)
#6-32 set screws on the faceplate to allow
accessory to rotate freely.
4. Accessory can rotate 360° independently of
faceplate.
5. When set in final position, tighten (2) #6-32
set screws using a 7/64” allen wrench.
2. Install faceplate using a 1/8” allen wrench
and hand-tighten the (5) #10-24 faceplate
screws in a star pattern to 30” lbs. min.
Do not use a power tool to install screws. Do
not exceed 40” lbs.
1. Before Installation of faceplate, clean o-ring
groove and collar of debris for a proper seal.
Failure to clean groove of debris will cause
fixture to fail and void product warranty.
Instructions Apply to...
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
Rock Guard
with Optical
Opening
Rock Guard Glare Shield B Half Dome B