B PLUS TV PlasmaLoop User manual

PlasmaLoop
User Manual

Contents

Acknowledgement
Thank you for buying PlasmaLoop device. We appreciate your trust and will
be pleased if you will share with us your experience and observation during
PlasmaLoop device usage.
Important instructions
Please, read this device manual carefully.
Never use the PlasmaLoop plasma tube as handle for manipulation with
the device. Plasma tube has not been constructed to hold the device
weight.
PlasmaLoop may affect the function of peacemakers and others implanted
devices – consult with your doctor about its use.
Do not use PlasmaLoop near gas station, always turn it off near flamable
material.
Handle the device and accessories with care, protect it from falling,
mechanical damage, dirt and excessive temperatures. Never disassemble
it!
Do not expose this device to rain or moisture.
Do not touch the plasma tube while the device is powered on!
Do not clean PlasmaLoop with water or cleaning agents. Only use wet
towel to clean the device while it is disconnected from power!
If you transport PlasmaLoop from cold to room temperature, do not power
on the device and wait 2 hours so that the temperatures balance.
If PlasmaLoop causes interference with other devices, especially with
radios and other wireless devices, PlasmaLoop user has to work on
elimination of said interference. We recommend to move PlasmaLoop
further away from said device, rotate or move PlasmaLoop.

Introduction
PlasmaLoop has been designed for contactless and convenient disposal
of microorganisms (viruses, fungi, bacteria). It is a Tesla-Rife generator
of electromagnetic field, which was made for scientific educational and
laboratory purposes.
Unlike the original Tesla generator of electromagnetic field generated
by conversion of alternating current in a classical spiral coil, PlasmaLoop
combines two principles and follows the work of R.R Rife, who used Hertz
dipole as an antenna emitting electromagnetic spectrum of low and
medium frequencies superimposed on noise source of spectrum generated
by plasma discharge. PlasmaLoop is new and original in the way, that it
combines the original Tesla generator with a Rife generator, where the plasma
discharge is concentrated in a single-thread coil - tube, significantly
increasing the intensity of the near electromagnetic field in the H
(magnetic field) component. In principle, this "antenna" is close to MLA
(Magnetic Loop Antenna) and builds on several years of development and
research of BTV in this area, which is, among other things. shown by a
number of industrial protection certificates - national and EU.
It is not recommended to use PlasmaLoop as an amateur and for other
than study, scientific and laboratory purposes, as the interaction of these
types of electromagnetic fields with living tissue is not yet scientifically proven.

Package content
PlasmaLoop
Cable Cinch-Jack
Power supply
Description of connectors connection
1. Signal input - cinch (RCA)
2. Power input – (19V DC, 25W max., )
Fig. 1: Description of connectors connection

Commissioning
The device is in standby mode after being connected to a power source. After
connecting the input signal from external generator, it is automatically turned on
and generates mag. field with the same frequency as the input signal.
Controls description
PlasmaLoop has no controls. It turns on automatically by connecting the
power source and by the signal from external generator at the input
connector.
All frequencies and frequency shifts are set on the external generator. The
ElZapp frequency generator is primarily recommended as a generator
device. Super Ravo Zapper or F-Scan can also be used as an alternative
generators. Other electrically compatible devices might also be used after
consultation with manufacturer.

Near field antenna pattern
Fig. 2: Front view.
Fig. 3: Side view.

Fig. 4: Top view.

Technical specifications
Power supply
Input voltage
18-20 V DC
Maximum input power
25W
General
Device format Table top device
Dimensions
36 x 15 x 49 cm
Weight
1 5kg
Operation temperature
0 – 35 ºC
Maximal operation humidity 90% non-condensating
Length of any connected cable is not
larger than 3m.
Standard frequency
1 2MHz
Lower range (modulation)
0 001 – 200 kHz
Higher range
200 kHz – 1 MHz
Input signals
Digital input (Cinch/RCA)
5 – 15Vp
Input frequency
0 001 Hz – 1 MHz

Safety and Ecology
1 Used electrical equipment
PlasmaLoop is an electrical appliance. This means that it cannot
be treated as normal household waste. Never dispose of
PlasmaLoop in normal municipal waste! Once used, it must be
handed over to the appropriate collection point where it will be
recycled or disposed of in an environmentally friendly manner.
Failure to follow these guidelines is illegal. This product may
contain substances dangerous to the environment - proper
handling is important for its protection. For more detailed information on how to
handle the product, contact your dealer or local authority.
Manufacturer
B PLUS TV a.s.
Požárnická 140
742 83 Klimkovice
IČ: 47677481 DIČ: CZ 47677481
www.btv.cz
Distributor

Notes