Baader Planetarium 2958550 User manual

Instructions
Protective T-Ring CANON EOS
Protective T-Ring for CANON EOS
#2958550 (basic version: T-Ring without filter)
(scope of delivery e.g. version 2958550C – with built-in clear protective filter
with Phantom GroupTM multi-coating
Instructions for use:
as of 11/11
The Protective T-ring for the Canon EOS allows Baader filters to be used with a T-ring,
providing the largest possible free aperture of 47.3mm (M48 thread), and protecting the camera
body from dust and humidity. To allow optimal use of the Protective T-ring, several versions of
it are now available with a built-in 50.8mmx3mm or 50.4mmx 3mm Baader filter.
The Protective T-ring not only offers exposures free from vignetting with extremely short focal
length telescopes, it can also be universally connected. Four different types of telescope
connection are included. The adapters of our Astro T-2 system can be used for many other
types of mounting onto a large range of telescopes.
After carefully examining the CANON bayonet fitting we have optimized the fit and tolerances
between the camera bayonet and T-ring. The result is the Protective T-ring, which is wobble-
free and has no lateral play thus always guaranteeing a stable image platform, even for long
exposures or when the telescope slews.
The Protective T-ring replaces other built-in camera filters which are installed directly into the
camera body. All unmounted 50.8mm or 50.4mm Baader filters, and Baader 2" filters mounted
in low-profile filter cells (LPFC) may be used with the Protective T-ring. (LPFC describes all
Baader filter mountings where the effective overall height of the filter cell is not more than 6
mm).
21.11.2011 Page 1G:\Anl\Baa\Zub\Protective\ProtectiveT-Ring-CanonEOS-e.doc

Instructions
Protective T-Ring CANON EOS
The glass thickness (3mm) of the built-in 50.8x3mm filter is taken into account in the
mechanical construction. The resulting effective overall optical length for each CANON EOS
camera thus amounts to 55mm - precisely the overall optical length of standard T-rings.
If, instead of a 3mm thick filter, a normal Baader 2" Filter with a low profile filter cell is used, the
effective overall height of 55mm deviates from the standard by just +0.3mm. This deviation is
negligible.
Included in delivery:
1. Protective T-Ring for CANON EOS body
2. Optional: Baader clear protective filter, 50.8mm x 3mm (protective T-rings are available with
a range of pre-assembled filters – see price list or the label on the product packaging)
3. Temperature compensation ring (to prevent filter damage at high temperatures)
4. S52/M48 adapter ring (M48 corresponds to the international 2" Astro filter thread)
5. M48/T-2 insert ring
6. S52/2" connector socket (with additional 2" M48 filter thread on the front side)
7. 1.5mm Allen key
When supplied with filter, a Baader clear protective 50.8mm filter is built
in to the Protective T-ring for the CANON EOS for example. The
S52/M48 adapter, as well as the M48/T-2 insert ring, are similarly pre-
assembled – however, the M48/T-2 insert ring is only loosely screwed in.
As supplied:
(Fig. 2)
21.11.2011 Page 2G:\Anl\Baa\Zub\Protective\ProtectiveT-Ring-CanonEOS-e.doc
Fig. 1: Included in delivery and assembly sequence:
(The unmounted filter is only shown here to illustrate the assembly sequence!)

Instructions
Protective T-Ring CANON EOS
Fig. 3: Illustration:
Protective T-Ring for
Canon EOS with 2"
socket (S52/2")
Changing the filter:
To change the filter, loosen the 6 grub screws on the side of the unit by means of the 1.5mm
Allen key supplied. Then tilt the body of the Protective T-ring carefully forward and take out the
built-in 50.8mm filter and the Delrin temperature compensation ring. Now insert another 50.8mm
or 50.4mm filter and place the temperature compensation ring on top of it. Now put either the
S52/M48 ring or the S52/2" connector socket into the body and fasten the unit together by
means of the 6 Allen screws. Here, S52 is a description of the diameter of the retaining cone
which is clamped in place by means of the 6 screws.
Alternatively, you can install a Baader 2" low profile filter. This is screwed in from the inside into
the M48 thread in the main body of the T-ring. After this - as previously described - either the
S52/M48 ring and the M48/T-2 or the S52/2" connector socket can be inserted and tightened up
by means of the 6 Allen screws.
The FILTER SHOULD ‘RATTLE’! This is not a defect. The slight looseness of the filter in the
mounting is very small and serves to protect the filter against stress. This minimal play will not
affect the image position.
21.11.2011 Page 3G:\Anl\Baa\Zub\Protective\ProtectiveT-Ring-CanonEOS-e.doc

Instructions
Protective T-Ring CANON EOS
Applications:
Fig. 4:
Protective T-Ring for CANON EOS, with 50.8mm clear protection filter,
Delrin temperature compensation ring, S52/M48 adapter and M48/T-2 insert ring
Fig. 5:
Protective T-Ring for CANON EOS with 50.8mm clear protection filter,
Delrin temperature compensation ring and S52/2" connector socket
21.11.2011 Page 4G:\Anl\Baa\Zub\Protective\ProtectiveT-Ring-CanonEOS-e.doc

Instructions
Protective T-Ring CANON EOS
Fig. 6:
Protective T-Ring for CANON EOS, shown with Baader 2" clear protection filter
in low profile filter mounting, S52/M48 adapter and M48/T-2 insert ring
Fig. 7:
Protective T-Ring for CANON EOS, shown Baader 2" clear protection filter
in low profile filter mounting and S52/M48 adapter ring
21.11.2011 Page 5G:\Anl\Baa\Zub\Protective\ProtectiveT-Ring-CanonEOS-e.doc

Instructions
Protective T-Ring CANON EOS
Fig. 8:
The Protective T-ring is supplied with
inserted S52/M48 ring and with the
M48/T-2 reducing ring screwed in. The
connector socket S52/2" is separate.
To employ the M48 thread instead of
the T-2 thread to attach the Protective
T-ring to your setup, simply undo the
loosely attached M48/T-2 insert ring by
using two fingers in the slots provided
and unscrew the insert ring
anticlockwise.
If the M48/T-2 insert ring is screwed in
too firmly after previous use, we
recommend using a spanner with 2mm
pins for disassembly (see Fig.8A). This spanner is available from tool shops.
Fig. 8A: Optional, adjustable 2mm face spanner (#2450062)
Fig. 9:
To use the 2" connector socket, loosen the 6
grub screws on the side that retain the
S52/M48 ring with the 1.5mm Allen key
supplied and remove it from the body.
Caution: When the 6 grub screws are
loosened and the S52/M48 ring removed, the
50.8mm filter is no longer secure and can fall
out of the front of the body of the Protective
T-ring. To avoid this, do not tilt the base
forward.
Now insert the 2" connector socket and
tighten the 6 Allen screws carefully and evenly. Sufficient tightness is achieved by using the long
side of the Allen key.
21.11.2011 Page 6G:\Anl\Baa\Zub\Protective\ProtectiveT-Ring-CanonEOS-e.doc
Loosen the 6
grub screws on
the side by means
of 1.5mm Allen key
supplied
Removing the 2" connector socket: