Baby Trend Nursery Center PY90973 User manual

Convenience through innovation and thoughtful design
Instruction Manual
Read all instructions BEFORE assembly and USE of product.
KEEP INSTRUCTIONS FOR FUTURE USE.
04.09
www.babytrend.com
Convenience through innovation and thoughtful design
IF YOU EXPERIENCE ANY DIFFICULTY IN USING THIS PRODUCT,
PLEASE CONTACT OUR CUSTOMER SERVICE DEPARTMENT AT
1-800-328-7363 BETWEEN THE HOURS OF 8:00 A.M. AND 4:30 P.M. PACIFIC
STANDARD TIME FOR ASSISTANCE. PLEASE HAVE YOUR MODEL NUMBER AND
MANUFACTURING DATE AVAILABLE WHEN YOU CALL. THIS INFORMATION CAN BE
FOUND ON A SMALL STICKER UNDER THE PLAYARD.
Contact us by phone:
1-800-328-7363 (8:00am ~ 4:30pm PST)
or online http://www.babytrend.com
Contact us by mail:
Baby Trend, Inc.
1607 S. Campus Ave., Ontario, CA 91761
Mini Playard
Nursery Center
Playard (fully assemble) x 1
Mattress x 1
Changing Table x 1
Long Curved Bar x 2
Short Bar with Connector Knob x 2
Music Center x 1
---------------------------------------------
Travel / Storage Bag x 1
Close N Cozy (Type C)
Soft Goods x 1
Strap Set x 1
Mattress Support Bar x 2
Lower Bar x 2
Center Cross Bar x 1
Upper Back Bar x 1
Upper frame x 2
Side frame x 2
Leg x 4
Screw x 4
Item#: PY90973
Check that you have all the below parts for this model
before assembling the playard.
This unit does not equipped with basket, bassinet, mobile,
parent organizer and canopy.

1Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved.
Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved. 2
WARNING: NEVER LEAVE INFANT IN
PRODUCT WITH SIDES DOWN.
Infant may roll into space between pad and
loose mesh side causing suffocation.
WARNING:
Infants can suffocate:
• In gaps between a mattress too small or too thick and product sides
• On soft bedding
Never add a mattress, pillow, comforter, or padding.
Use only the mattress provided by manufacturer.
Never use a water mattress with this product.
WARNING: See playard oor and side rails for warnings.
WARNING: Failure to follow these warnings and the
instructions could result in serious injury or death.
• The playard, including side rails, must be fully erected prior to use. Make
sure latches are secure.
• Strings can cause strangulation! NEVER place items with a string around
a child's neck such as hood strings or pacier cords. NEVER suspend
strings over playard or attach strings to toys.
• Discontinue use of the product when child is able to climb out or has
reached the height of 35 in. (890 mm) or weight of 30 lbs. (14 kgs),
whichever comes rst.
• When child is able to pull to standing position, remove bumper pads, large
toys and other objects that could serve as steps for climbing out.
• NEVER place product near a window where cords from blinds or draps
can strangle a child.
• Always provide the supervision necessary for the continued safety of your
child. When used for playing, NEVER leave child unattended.
• To reduce the risk of SIDS, pediatricians recommend healthy infants be
placed on their back to sleep, unless otherwise advised by your physician.
Contact us by phone:
1-800-328-7363 (8:00am ~ 4:30pm PST)
or online http://www.babytrend.com
Contact us by mail:
Baby Trend, Inc.
1607 S. Campus Ave., Ontario, CA 91761
WARNINGWARNING
• NEVER use this product if there are any loose or missing fasteners, loose
joints, broken parts, or torn mesh/fabric. Check before assembly and
periodically during use. Contact Baby Trend Customer Service at
1-800-328-7363 for replacement parts, repair or instructions. NEVER
substitute parts.
• NEVER leave child in product with sides lowered. Be sure sides are in
raised and locked position whenever child is in product.
• NEVER use plastic shipping bags or other plastic lm as mattress covers
not sold and intended for that purpose. They can cause suffocation.
• This product is not intended for commercial use.
MAINTENANCE AND CLEANING INSTRUCTIONS:
Use only household mild soap and warm water.
DO NOT USE BLEACH.
DO NOT MACHINE WASH.
If you experience any difculty with the use of our product or have a
question regarding these instructions, please contact our Customer
Service Department at 1-800-328-7363 between the hours of
8:00 a.m. and 4:30 p.m. (PST). Please do not return the product to the
store as once it is returned it cannot be re-sold and the materials and
energy used to make it are wasted.

Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved.
Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved.
PARTS
TO ASSEMBLE PLAYARD
ATTENTION:
Playard must be fully assembled and securely
locked before installing or using other accessories.
1. Unzip bag and remove Playard frame (Fig. 1).
Undo the three (3) Fasten straps and set the
Mattress aside (Fig. 2).
2. Turn the Playard right side up and keep the
Legs and Wheels close together. Stretch out
top of Playard and pull up one side at a time of
each of the top rails until each latch “Clicks”
and locks securely into place (Fig. 3).
NOTE: The best way to lock the rail(s) is to
hold one hand on each side and pull up sharply.
(DO NOT pull from the middle where the latch
release is located).
IMPORTANT: The handle located in the center
of the Playard oor MUST remain raised
(Approx. 45.7 cm or 18 inches) while locking
the side rails in place. If the center is not raised
the rails will NOT lock.
If you experience difculty and one side of the
rail will lock but the other side will not then,
unlock the rail by squeezing the release in the
center and try again. If you still have difculty,
contact our Customer Service Center at
1-800-328-7363 or visit us online at
www.babytrend.com.
ASSEMBLY
34
mp3
input
sleep play nature
Playard
Mattress
Bassinet Metal Support Tubes
(2 male, 2 female)
Travel / Storage Bag
Long Curved Bar (2)
Changing Table
Parent Organizer*
Short Bar with Connector
Knob (2)
Music CenterFixed Mobile
* Type may vary
This model may not include some features shown below. Check the parts list to make sure
you have all the parts for this model before assembling the playard.
IMPORTANT! To ensure safe operation of your playard,
please follow these instructions carefully. Please keep these
instructions for future reference.
IMPORTANT! Before assembly and each use, inspect this
product for damaged hardware, loose joints, missing parts or sharp
edges. NEVER use if any parts are mssing or broken.
IMPORTANT! Adult assembly is required.
Fig. 1
Fig. 2
Playard
Mattress
Fig. 3
Fig. 4

Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved.
Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved.
ASSEMBLY ASSEMBLY
56
3. To operate the brakes on the Wheels, press
downward on the brake levers. To release, lift
upward on the lever (Fig. 4)
4. Once all four (4) top rails are locked in place,
push down on the center handle (Fig. 5). The
center mechanism will rotate clockwise 90
degrees and automatically lock in place.
IMPORTANT: Test each top rail by pushing
down slightly to conrm each is rigid and
locked securely in place before use (Fig. 6).
ATTENTION:
To use as a bassinet, skip to page 8 for bassinet
installation instructions.
5. Place the Mattress on the oor of the Playard
with the padded side facing up (Fig. 7)
6. Feed the three (3) hook and loop straps located
on the underside of the Mattress through the
slots in the oor of each end of the Playard
(Fig. 8). Fasten the hook and loop straps to the
underside of the Playard oor to prevent the
Mattress from moving (Fig. 9).
FOLDING PLAYARD
1. Undo the three (3) hooks and loop straps
holding the Mattress from underneath the
Playard oor or remove the Mattress for the
Bassinet and set aside.
2. Grasp the center handle, push down and rotate
the handle counter-clockwise 90 degrees and
lift upward until the handle is as high as the top
rails (Fig. 10). Gather the Legs and Wheels
together towards the center as close as possible
so that they nearly touch (Fig. 11).
NOTE: The top rails of the Playard are sill in
the “Locked” position.
3. Locate the rail release lever in the center and
bottom side of each rail. Lift slightly while
squeezing the lever until the rail “Clicks” and
releases. Push down each side of the rail while
still holding the release lever until both sides
are down. Repeat for all remaining sides
(Fig. 12).
NOTE: If the top rail(s) do not release
completely, DO NOT FORCE! Check the
oor of the Playard to make sure all the bottom
rails are unlocked and make sure the middle
handle is pulled up and has not fallen back
down. If so, repeat step #3.
4. Gather four (4) corners and center all together
tightly (Fig. 13).
5. Wrap Mattress around Playard frame with
padded side facing inward.
6. Secure the three (3) hook and loop straps by
feeding them through the loops on the end
of the Mattress and folding them back onto
themselves (Fig. 14).
7. Place folded Playard into carry bag so that the
handle comes through the opening between
each side of the zipper.
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Rotate before
lifting
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14

Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved.
Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved.
78
WARNING ASSEMBLY
WARNING: Failure to follow these warnings and the
instructions could result in serious injury or death.
FALL HAZARD: To help prevent falls, do not use this
product when the infant begins to push up on hands and knees or
has reached the height of 25 in. (635 mm), weight of 15 lbs. (6.8 kgs)
or 4 months old, whichever comes rst.
SUFFOCATION HAZARD : Infants can suffocate
• In gaps between an extra pad and sides of the bassinet/cradle
• On soft bedding
Never add a mattress, pillow, comforter, or padding.
Use only the pad provided by manufacturer.
Never use a water mattress with this product.
• To reduce the risk of SIDS, pediatricians recommend healthy infants be
placed on their back to sleep, unless otherwise advised by your physician.
• The playard, including side rails, must be fully erected prior to use. Make
sure each latch is secure.
• Strings can cause strangulation! NEVER place items with a string around
a child's neck such as hood strings or pacier cords. NEVER suspend
strings over bassinet or attach strings to toys.
• Discontinue use of the bassinet or the changing table when child begins to
push up on hands and knees or has reached the height of 25 in. (635 mm),
weight of 15 lbs. (6.8 kgs) or 4 months old, whichever comes rst.
• NEVER place product near a window where cords from blinds or drapes
can strangle a child.
• Always provide the supervision necessary for the continued safety of your
child. NEVER leave child unattended.
• NEVER use plastic shipping bags or other plastic lm as mattress covers
not sold and intended for that purpose. They can cause suffocation.
• Use bassinet with only one child at at time.
• NEVER place a child under the bassinet.
• NEVER store the bassinet in the playard while in use.
• The bassinet must be fully assembled and installed before using.
• STRANGULATION HAZARD: NEVER leave the changing table
in place when the child is in the bassinet or the playard. Always ip
changing table down while not in use.
• To prevent your child from falls and other injuries, always use safety belt
when child is on the changing table, always stay within arm's reach of
your child when using the changing table.
• To help prevent heat build-up inside the playard and to avoid overheating
your child, when using the bassinet NEVER use an outdoor canopy.
ACCESSORIES TO ASSEMBLE BASSINET
ATTENTION:
Playard must be fully assembled and securely
locked before installing or using the bassinet
feature. (See To Assemble Playard section)
You will need to remove the mattress from the
bottom of the Playard to use inside your Bassinet.
1. Position the Bassinet over and down into the
fully assembled Playard. Secure in place by
pushing down rmly on each plastic support
clip until all are snapped into place (Fig. 15).
2. Assemble Mattress Support Tubes (if
equipped; otherwise, skip to step 4) by
inserting the two (2) male tubes into the two
(2) female tubes (Fig. 16).
3. Insert both, assembled, Mattress Support
Tubes into the loops provided on the bottom
of the Bassinet (Fig. 17).
4. Place the Mattress into the Bassinet with the
padded side facing upward (Fig. 18)
NOTE: Fasten tabs underneath the Mattress
secure it in place.
TO REMOVE BASSINET
1. Remove Mattress from Bassinet.
2. Remove Canopy.
3. Unsnap all clips and lift Bassinet.
Bassinet
Metal Support Tubes
(2 male, 2 female)
Fig. 15
Fig. 17
Fig. 18
Fig. 16

Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved.
Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved.
ASSEMBLY
9
10
ASSEMBLY
MOBILE ASSEMBLY (Fixed)
ATTENTION: DO NOT attach Mobile to Canopy until Canopy is correctly installed
as noted in the Canopy instructions.
A crib mobile is intened for visual stimulation and is not intended to be grasped by the child.
If attached to the crib or playpen, remove when baby begins to push up on hands and
knees. If so designed, mount on wall or ceiling clearly out of a standing baby's reach.
Always attach all provided fasteners (strings, straps, clamps, etc.) tightly to a crib or
playpen according to the instructions. Check frequently.
DO NOT add additional strings and straps to attach to a crib or playpen.
DO NOT attach the Mobile with child in Playard or Bassinet.
DO NOT remove the Mobile before retracting the Canopy or removing the Canopy.
(a)
(b)
(c)
(d)
(e)
Fixed Mobile
Contents:
(a) 1 Mobile Lower Arm
(b) 1 Mobile Arm Holder
(c) 1 Mobile Upper Curved Arm
(d) 1 Mobile Tri-shaped Arm
(e) 3 Toys (toys may vary)
1. Insert the Mobile Lower Arm (a) into the
Mobile Arm Holder (b) untill locked together
(Fig. 19).
2. Insert the Mobile Upper Curved Arm (c) into
the Mobile Lower Arm (a, b) until locked
together (Fig. 20).
3. Snap the Mobile Tri-shaped Arm (d) onto the
end of the Upper Curved Arm (a, b, c)
(Fig. 21). Connect each of the three Toys (e)
to the Mobile by threading the string into the
slot at the end of each arm.
4. Insert the bottom of the Mobile Arm into the
frame of the Playard (Fig. 22).
(a)
(b)
Fig. 19
(c)
(a)
(b)
Fig. 20
Fig. 21
Fig. 22
(d)
(e)
(a) (b)
(c)
Fig. 23
Fig. 24
Fig. 25
WARNING
FALL HAZARD: To
prevent death or serious injury,
always keep child within arm's
reach.
Always use restraint belt to prevent
falls, see page 15 for details.
Contents:
(a) 2 Long Curved Bars
(b) 2 Short Bar with Connector Knobs
(c) 1 Changing Table
ATTENTION:
Playard must be fully assembled and securely
locked before installing or using the changing
table feature. (See To Assemble Playard section)
1. Connect the two (2) Long Curved Bars
together (Fig. 23).
2. Insert the assembled curved bars into the
Changing Table fabric (Fig. 24) Slide the
Curved Bars around inside sleeve of the
Changing Table.
3. Connect the two (2) Short Bars to each end
of the Long Curved Bar (Fig. 25) Make sure
that the knobs are both facing down and the
same direction on each end. (Fig. 26)
Fig. 26
TO ASSEMBLE CHANGING TABLE

Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved.
Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved.
15 16
ASSEMBLY ASSEMBLY
4. Insert Connector Knob Prongs into holes
located on both corners of the Playard
(Fig. 27).
5. Turn the Connector Knobs counter clockwise
to lock into place (Fig. 28).
6. Flip Changing Table over onto Playard
(Fig. 29).
7. Snap the two (2) buttons on the ap down
onto the Playard (Fig. 30.
IMPORTANT: Check that the Changing Table
is correctly and securely installed BEFORE
each use.
To use changing table
restraint system
1. Place child on changing table, make sure hand
and arms are clear of the restraint. Bring the
restraint around the child's waist and clip the male
and female ends of the buckle together. (Fig. 31)
2. Tighten strap until ts snug around child's
waist. DO NOT OVER TIGHTEN. (Fig. 32)
3. To remove, unsnap the buckle.
ATTENTION:
NEVER use changing table if it is damaged or
broken.
Fig. 36
To remove changing table
Flip Changing Table to the outside of the Playard.
Unsnap fabric ap of Changing Table from
Playard. Twist Connector Knobs clockwise to
unlock. (Fig. 33) Remove Changing Table from
Playard (Fig. 34) and disconnect the Short Bars
from the Curved Bar by pressing on the snap
buttons and pulling apart. Remove Curved Bar
from Changing Table sleeve.
Fig. 27
Fig. 28
Fig. 33
Fig. 30
Fig. 34
Fig. 29
Fig. 31
Fig. 32
PARENT ORGANIZER ASSEMBLY
1. Parent Organizer: Position each hook so that
the hooked end is facing the rear side of the
organizer. Press the hook down rmly into the
slot until it snaps into place. (Fig. 35)
Diaper Stacker: Skip to step 2.
2. Connect the Parent Organizer/Diaper
Stacker to the Playard by sliding the two (2)
connecting clips over an open portion of the
top rail of the Playard. (Fig. 36)
NOTE: The Parent Organizer/Diaper Stacker
can only be installed on open sides of the
Playard where the connecting clips can easily
be attached without interfering with other
features.
Parent Organizer Diaper Stacker
or
Fig. 35

Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved.
Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved.
17 18
ASSEMBLY ASSEMBLY
MUSIC CENTER
The Music Center is designed to be attached to
the playard corners. It can be attached on the
Changing Table's side or the Canopy's side. See
gure 37.
MUSIC OPERATION
The Music Center requires 4 AA batteries. Please
see gure 38 for battery installation. Unscrew
the battery door screws and pull outward on the
battery door. Install batteries as shown. Re-install
battery door and secure with screws.
To active the unit, press the on/off button.
Press button a second time to switch unit off.
To listen to SLEEP music, press the SLEEP
button. You may use the previous / next
button to change the song. The Vol or
Vol buttons control the units volume.
To listen to PLAY music, press the PLAY
button. You may use the previous / next
button to change the song. The Vol or
Vol buttons control the unit's volume
WARNING: Keep batteries out of children's reach. Old and
new batteries should not be mixed. Alkaline, standard carbon-zinc, and
rechargeable nickel-cadium batteries should not be mixed. Remove
batteries before storing music center for a long period of time.
Fig. 38
Fig. 37
To listen to NATURE sounds, press the
NATURE button you may use the previous /
next button to change the sound. The Vol
or Vol buttons control the unit's volume.
VIBRATION: To use the vibration button
press down once to active the speed, press
again for a Medium speed and once more for
the faster speed. Press to reduce the speed.
NIGHT LIGHT: To use the night light, press
the button. The light has 3 settings of
brightness and is controlled by the button.
VOICE RECORDER: To use the Voice
record function press the button and
speak into the microphone to record your 10
second voice message. Press to hear the
message.
VOICE ACTIVATION: To use the Voice
Activation function press the button twice
if the unit is power off. If the unit is already
power on, press the button once. The
voice activation light will be illuminated
when in voice activation mode. If your infant
cries his/her voice will activate the sleep
music to come on and play. When voice
activation is enabled, sleep mode is active for
2 hrs.
MP3 FUNCTION: Use the input jack to
attach your MP3 player into the unit .
Press the button to select the MP3 input.
Your MP3 music will then be played through
the unit and will over-ride the unit’s music.
To listen to the unit’s music, depress the
button. Volume will be controlled by the MP3
player.
_+
_
_
+
+
_
+
Recording Indicator
MP3 Indicator
Voice Activation
Indicator