Baby Trend High Chair User manual

Convenience through innovation and thoughtful design
Instruction Manual
Read all instructions BEFORE assembly and USE of product.
KEEP INSTRUCTIONS FOR FUTURE USE.
05.08
www.babytrend.com
Convenience through innovation and thoughtful design
IF YOU EXPERIENCE ANY DIFFICULTY IN USING THIS PRODUCT,
PLEASE CONTACT OUR CUSTOMER SERVICE DEPARTMENT AT
1-800-328-7363 BETWEEN THE HOURS OF 8:00 A.M. AND 4:30 P.M. PACIFIC
STANDARD TIME FOR ASSISTANCE. PLEASE HAVE YOUR MODEL NUMBER AND
MANUFACTURING DATE AVAILABLE WHEN YOU CALL. THIS INFORMATION CAN BE
FOUND ON A SMALL STICKER UNDER THE SEAT.
Contact us by phone:
1-800-328-7363 (8:00am ~ 4:30pm PST)
or online http://www.babytrend.com
Contact us by mail:
Baby Trend, Inc.
1607 S. Campus Ave., Ontario, CA 91761

WARNING
1Copyright © 2007 - 2008, Baby Trend Inc., All Rights Reserved.
Copyright © 2007 - 2008, Baby Trend Inc., All Rights Reserved. 2
WARNING: Failure to follow these warnings and the
instructions could result in serious injury or death.
WARNING: Prevent serious injury or death from falls or
sliding out. Always secure child in the restraint. NEVER leave
child unattended.
WARNING: The child should be secured in the high chair
at all times by the 5-point restraining system, either in the reclining,
semi-reclining or upright position. The tray is not designed to hold
the child in the chair. It is recommended that the high chair be
used in the upright position only by children capable of sitting
upright unassisted. See page 5 for instructions on proper use of
restraint system.
• Other accessory items may change the balance of the high chair and cause
hazardous unstable conditions, use approved Baby Trend toys.
• Be certain the high chair is fully erect and latched in the open position
before allowing the child near the high chair.
• Use of the high chair with a child weighing more than 40 pounds will
cause excessive wear and stress on high chair.
• The maximum weight that can be carried in the basket is 5 lb. Excessive
weight may cause a hazardous unstable condition to exist.
• NEVER allow your high chair to be used as a toy.
• NEVER use this product if there are any loose or missing fasteners, loose
joints, broken parts, or torn mesh/fabric. Check before assembly and
periodically during use. Contact Baby Trend Customer Service at
1-800-328-7363 for replacement parts, repair or instructions.
NEVER substitute parts.
Contact us by phone:
1-800-328-7363 (8:00am ~ 4:30pm PST)
or online http://www.babytrend.com
Contact us by mail:
Baby Trend, Inc.
1607 S. Campus Ave., Ontario, CA 91761
If you experience any difculty with the use of our product or have a question
regarding these instructions, please contact our Customer Service Department at
1-800-328-7363 between the hours of 8:00 a.m. and 4:30 p.m. (PST). Please do
not return the product to the store as once it is returned it cannot be re-sold and the
materials and energy used to make it are wasted.
PARTS
123
4
8
5
9
12
11
10
6
7
1Seat Back
Height Brackets
Tray Insert
Tray
Upper Frame Assembly
Seat Back Hinge Rod
Seat Base
Crotch Retainer
Legs
4 (3.5mm x 10) Screws
Footrest
4 Casters (with brakes)
Seat Pad
Seat Insert (optional)
Basket (optional)
Music Toy (optional)
Teething Toy (optional)
2
3
4
5
6
10
11
12
13
14
15
7
13 14
16
15 16 17
8 17
9
This model may not include some features shown below. Check that your have all the
parts for this model before assembling the high chair.

Copyright © 2007 - 2008, Baby Trend Inc., All Rights Reserved.
Copyright © 2007 - 2008, Baby Trend Inc., All Rights Reserved.
IMPORTANT! To ensure safe operation of your product,
please follow these instructions carefully. Please keep these
instructions for future reference.
IMPORTANT! Before assembly and each use, inspect this
product for damaged hardware, loose joints, missing parts or sharp
edges. NEVER use if any parts are missing or broken.
IMPORTANT! Adult assembly is required.
IMPORTANT! Always check that the high chair is locked
in the open position before using.
ATTENTION:
Carefully remove parts from box. Check that you
have all the parts for this model before assembling
the high chair. NOTE: Certain High Chair models
are packaged with the High Chair Seat Fabric and
Seat Insert already attached to the Seat Back.
TO ASSEMBLE SEAT
1. Place the Seat Base on a at surface as shown
in gure 1.
2. Join the Seat Back to the Seat Base using the
Seat Back Hinge Rod as shown in gure 2.
The rod is inserted from right to left as shown.
Fig. 1
ASSEMBLY ASSEMBLY
34
Fig. 4
Fig. 2
3. Slide the left and right sides’ Height Bracket
onto the Seat Base (Fig. 3). Snap the brackets
in place (Fig. 4).
4. Slide the Footrest onto the Seat Base as shown
in Figure 5. Snap Footrest into place.
5. Insert the front tube of the right side Upper
Frame Assembly into the Height Bracket
(Fig. 6). The front tube is easily distinguished
from the rear tube by the array of holes located
on the backside of the tube.
6. Squeeze the Red Release Handle and push the
tube through the Height Bracket until it locks
on the highest position (Fig. 7).
7. Repeat Steps 5 and 6 for the left side Upper
Frame Assembly (Fig. 8).
Fig. 3
Fig. 5
Seat Back
Seat Base
Seat Back
Hinge Rod
Height Bracket
Height Bracket
Footrest
Upper Frame Assembly
Height Bracket
Red Release
Handle
Fig. 6
Fig. 7
Fig. 8

Copyright © 2007 - 2008, Baby Trend Inc., All Rights Reserved.
Copyright © 2007 - 2008, Baby Trend Inc., All Rights Reserved.
Fig. 9
Fig. 10
Hole
Hole
Push
Buttons
Hole
Push
Buttons
56
8. Insert the Legs into the ends of the front
tube of both the right and left Upper Frame
Assemblies (Fig. 9). Note: Legs are properly
connected when the push buttons are lined up
with the holes on the ends of the Upper Frame
Assembilies. Make sure the push buttons are
engaged before use.
9. Insert another Leg into the ends of the rear
tube of both the right and left Upper Frame
Assemblies (Fig. 10).
10. Attach each of the Casters to the high chair
feet as shown in Figure 11. Snap casters into
Bottom of the foot. Check that all four Casters
are securely fastened to the High Chair.
11. Flip over Tray to attach Crotch Retainer. The
molded plastic housing must be oriented by
facing the slot toward front of the Tray. Insert
the 4 (3.5mm X 10) Screws and tighten.
DO NOT OVER-TIGHTEN (Fig. 12).
Fig. 11
TO ATTACH SEAT PAD
NOTE: Certain High Chair models are packaged
with the High Chair Seat Pad and Seat Insert
already attached to the Seat Back. If your model
has a Seat Pad and Seat Insert on the Seat Back
please skip ahead to Step 2.
1. Loop the ap on the back of the pad over the
top of the Seat Back. Connect the Seat Pad
to the Seat Back with the two Elastic Loops.
These t over the Attachment Tabs located near
the top harness slots (Fig. 13).
2. Attach the bottom of Seat Pad to the Seat Base
with the two Elastic loops located at the rear of
the bottom of the Seat Pad. These t over the
Attachment Tabs located on the Seat Base near
where the Seat Back and Seat Base Join.
(Fig. 14)
3. Set Seat Insert onto Seat Pad.
4. Thread non-buckle end of Harness Straps
called Harness Attachment Tabs through the
provide slots in the Seat Fabric, Seat Insert,
Seat Back, and Seat Base (Fig. 15). When
Harness Attachment Tabs are through the
provided slots, rotate the Harness Attachment
Tabs 90 degrees. Make sure that the straps are
rmly in place.
TO REMOVE SEAT PAD
Reverse steps above.
ASSEMBLYASSEMBLY
Fig. 12
Fig. 13
Fig. 15
Fig. 14

Copyright © 2007 - 2008, Baby Trend Inc., All Rights Reserved.
Copyright © 2007 - 2008, Baby Trend Inc., All Rights Reserved.
78
OPEN HIGHCHAIR
Push the legs apart until fully open and locked.
(Fig. 16) Push downward on fold levers (left and
right) to ensure frame is locked open.
WARNING: Always check
that the high chair is locked in the
open position before using.
WARNING: The tray is not
designed to hold the child in the
chair. The child must be secured by
the safety harness at all times while
in the high chair.
TO ATTACH AND
OPERATE TRAY
TO ATTACH TRAY
To attach the Tray, line up the grooves on the
bottom of the tray with the armrests of the high
chair. Squeeze the Tray’s release handle and
slide the tray onto the armrests (Fig. 17). The
Tray has a 3-position adjustment. To adjust the
position, squeeze the Tray’s release handle located
underneath the tray and reposition the tray to the
desired position (Fig. 18). Release the Tray’s
handle. Check that the Tray is securely locked in
its new position.
TO ATTACH INSERT TRAY
The dishwasher safe food Tray Insert snaps onto
the High Chair Tray and is held in place by tabs
on the sides of the Tray. When installing the
Tray Insert make sure that its snaps into place to
prevent the child from removing the Tray Insert.
To remove Insert unsnap tabs from the Tray.
OPERATION OPERATION
Push
Tray Release located
underneath tray
3-position
Fig. 16
Fig. 17
Fig. 18
Fig. 19
Push down to
lock open
RECLINE SEAT
Squeeze recline lever on back of the seat and
adjust to the preferred recline or upright position.
(Fig.19). When adjusting the seat back position,
be very careful that the child’s arms, hands or
legs do not get caught.
WARNING: It is
recommended that only children
capable of sitting upright
unassisted use the high chair in the
upright position.
WARNING: Prevent serious
injury or death from falls or sliding
out. Always secure child in the
restraint system, either in the reclining,
semi-reclining or upright position.
TO USE SAFETY BELT
The Tray is not designed to hold the child in
the chair. Always keep child in view while
in high chair. NEVER LEAVE CHILD
UNATTENDED.
1. Place your child’s arms through the loops
formed by the shoulder and waist straps. Place
the crotch strap between your child’s legs.
Insert the Harness Buckles into the Center
Clasp with the Red Button.
2. Adjust shoulder and waist straps for your
child’s comfort and safety by sliding buckles
in either direction. Safety straps are to t snug
around your child. (Fig. 20)
TO RELEASE SAFETY BELT
Push Red Button on Center Clasp, the two
Harness Buckles will pop free. (Fig. 21)
Adjust for a snug t
Fig. 20
Fig. 21
Center Clasp

Copyright © 2007 - 2008, Baby Trend Inc., All Rights Reserved.
Copyright © 2007 - 2008, Baby Trend Inc., All Rights Reserved.
OPERATION MAINTENANCE
9
10
6-position
WARNING: Do not adjust
seat height with child in seat.
Adjust seat height before placing
your child in the high chair.
TO ADJUST SEAT HEIGHT
Squeeze both left and right lever of the Height
Adjustment Bracket and adjust to the ideal
position. (Fig. 22)
WARNING: Always check
that the height adjustment bracket
is level and both left and right sides
locked before placing child in the
high chair.
TO FOLD HIGH CHAIR
The High Chair may be folded with the seat in any
of the height positions. The high chair will be the
most compact with the seat in the lowest position.
1. Place seat in the desired height position (Fig. 23).
2. Place Seat Back in the most upright position
(Fig. 19).
3. Squeeze the tray release handle and slide the
tray out. (Fig. 17) Hang the tray on the hooks
located on the back of the rear leg. (Fig. 23)
4. Pull upward on the release levers (located on
the sides of the frame) and push the rear legs
in the direction of the front legs until folded.
(Fig. 24) Chair is now ready to put away.
DO NOT allow your child to play around a
folded high chair as it may fall.
TO UNFOLD HIGH CHAIR
Push the legs apart until fully open and locked.
Push downward on the fold levers (left and right)
to ensure the frame is locked. (Fig. 16)
CARE AND MAINTENANCE
WARNING: Harness Straps and Basket are NOT washable.
Dishwasher safe Tray Insert
The Tray Insert is dishwasher safe to 160 degrees Fahrenheit. Do not use scouring pads
on the Tray Insert as they will damage the surface and the Tray Insert will become more
difcult to clean.
High Chair/Tray
Clean High Chair and Tray after each use using mild household dish soap. Please use only
a soft bristle brush, sponge or cloth to clean the surface or remove particles of food.
DO NOT submerge High Chair and Tray in water. Surface clean only.
Seat Pad (please refer to care label on the seat pad for cleaning instructions)
To remove the seat pad:
Remove Harness Straps by pushing Harness Attachment Tabs through the Harness slots on
the Seat Back, Seat Base, and Seat Pad. Remove Elastic Loops from Attachment Tabs on
Seat Base and Seat Back.
None-Washable Seat Pad:
Please use sponge or cloth with mild household detergents to surface clean the seat
pad. DO NOT MACHINE WASH the seat pad.
Washable Seat Pad:
Machine Wash COLD DELICATE CYCLE with non chorine based Laundry
Detergent. DO NOT USE BLEACH. HANG DRY. DO NOT MACHINE DRY.
Basket
NOTE: Certain Models will have a Basket underneath the seat for storage. These Models
will be packaged with the Basket already attached to the Seat Base.
To remove:
The Basket is attached by four snaps. Release these snaps for removal.
To attach:
Feed snap strips around Basket Slots underneath Seat Base. Press rmly on the four snaps.
Fig. 22
Fig. 23
Fig. 24
Fig. 25
TO ATTACH OR REMOVE TOY
TO ATTACH OR REMOVE MUSIC TOY
The Music Toy (Part # 16) is attached through the
suction cup on the bottom of the Toy. To attach
simply press the Toy on the Tray, to remove lift up
a part of the bottom of the cup.
TO ATTACH OR REMOVE TEETHING TOY
Press the Teething Toy (Part # 17) connector into
the curved slot in Tray edge and snap bottom
of connector over lower lip of Tray. Reverse to
remove the Toy (Fig. 25).