BabyMinder JBABYVERT User manual

WARNING! RETAIN FOR FUTURE REFERENCE. TO
AVOID SERIOUS INJURY OR DEATH PLEASE READ
CAREFULLY AND FOLLOW ALL INSTRUCTIONS.
WARNING! Parcels or accessory items, or both, placed
on the unit may cause the unit to become unstable.
WARNING! Recommended maximum weight for the
accessory hooks not to exceed 7.5 lb (3.4 Kg).
WARNING! Excessive weight applied to the accessory
hooks or the unit may cause a hazardous unstable
condition to exist.
WARNING! NEVER LEAVE THE CHILD UNATTENDED.
WARNING! Avoid serious injury from falling or sliding out.
Always use restraint system.
WARNING! Designed for Infants Only. Age up to 3.5
years and weighing less than 50 Ib. Keep one hand on
the child at all times.
Lay child in the centre of the changing table and clip together
the ends of the restraint belt. The belt should fit adequately so
the child cannot roll off the table or slide out of the restraint
belt. The restraint belt should never be tightened to the extent
that it interferes with the breathing of the child.
To shorten or lengthen the restraint belt pull the buckle in the
appropriate direction.
• All assembly fittings shall always be tightened properly.
• Follow mounting instructions carefully to assure secure
mounting to various types of wall material.
• Be aware of the risk of open flame. Do not mount the unit
near strong heat sources, such as electric furnaces, gas
heaters, radiators and fireplaces, etc.
• ALWAYS check restraints to make sure they are securely
fastened to the unit.
• Maximum weight of the child for use is 50 Ib (22.7 kg).
• This unit has a Changing Pad dispenser. Paper Changing
Pads should be stocked regularly to provide a safe and
sufficient barrier between the baby and changing bed.
• The Baby Changing Unit should be cleaned daily with a
disinfectant cleaner.
•
•
Check mountings for tightness on a regular basis.
If in doubt about the adequacy of sub-strate strength carry out
load test or confirm with a competent person.
MODEL: JBABYHOZII
B
8mm (0.31")
3mm (0.12")
8mm (0.31")
A
x4
B
x4
3
2
1
x4
x4 1
2
3
19.68" (500 mm)
9.84" (250 mm)
A
FLOOR
19.05" (484 mm)
52.95" (1345 mm)
15.75" (400 mm)
9.25" (235 mm)
FLOOR
45.89" (1165 mm)
MODEL: JBABYVERT
A
B
EN
EN INSTALLATION GUIDE BM_US_EN_020311 ISSUE A

Mounting on timber s
In order to avoid undue splitting of the timber the minimum edge distance
from the centre line of the screw shall be 35mm i.e. the timber stud must be
a minimum width of 70mm.
1. Changing Tables - Establish position of timber studs to ensure that all four
fixings are into timber and that the fixings are positioned
centrally within the studs. If this cannot be achieved
introduce horizontal noggins between the studs to suit.
3. Discard nylon plug.
4. Mark position of one of the top fixings (top fixing if seat) and drill 3mm
pilot hole to full depth of screw plus 5mm.
5. Insert screw through washer supplied and tighten using 8mm socket.
6. Align unit for level.
7. Drill remaining holes and complete installation.
tuds
or ceramic tile over timber studs
Mounting on concrete, brick
or masonry wall
1. Offer up the unit and mark wall for one of the top fixing positions
2. Drill hole accurately with 8mm dia. masonry drill to required depth of fixing
and screw allowing for thickness of unit and finishes.
3. Clean out dust from hole by blowing or suction.
4. Place washer onto the neck of the plug.
5. Insert fixing and washer through the unit until the washer bears against
the surface.
6. Using 8mm socket tighten screw against steel washer.
7. Align unit for level.
8. Drill remaining holes and complete installation
A
A Tile bed and unit thickness - 40mm maximum.
8mm
Fig.1
Notes:
EU Headquarters: Vectair Systems Limited North American Office: Vectair Systems Inc.
Unit 3 Trident Centre, Armstrong Road PO Box 11068
Basingstoke, Hampshire, RG24 8NU UK Memphis TN38111 USA
Phone: [phone] Phone: [phone]
Fax: [phone] Toll Free: 877 697 7276
E-mail: [e-mail] E-mail: [email protected]
Web: www.vectair.co.uk Web: www.vectairsystems.com