Badasheng BDS-662B User manual
Bluetooth headset
user manual
Model no. : BDS-662B
1 ) Product feature :
Using bone conduction technology , back
hang design releasing ears with build in
microphone and ultrasonic welding
technique with good sealing for water
resistant . With use of low energy
consumption version bluetooth module ,
suitable for smart phone , tablet . Capable of
receiving wireless stereo signal , you can
listen & control volume , music selection of
your music play . Echo cancellation design
assure clear conversation , conversation &
music play can be auto converted.
Audio transmission through bone conduction
help protecting your audition , your eardrum
& keep contact with surrounding , most suitable
for outdoor use .
2 ) Port function :
Right hand side of headset
1 , Volume - / previous music button
2 , Play / pause mutli-function button
3 , Volume + / next music button
4 , working indicating light
5 , Micro USB charging port
6 , Microphone port
3 ) Operation :
1 , Long press mutli-function button for 3 seconds
to power on headset while it’s power off ,
automatically run pairing mode with red / blue
light flashing and power off headset while it’s on .
2 , Searching for bluetooth device in your
smart phone or device manual
3 , Pair with BDS-662 , blue light will fast
flash twice if paired .
4 , During incoming call , blue light flashing
& headset will generate a incoming call tone ,
short press mutli-function button once for
answering call , another short press to end
call and long press to refuse call .
5 , During music play , blue light slow
flashing , press mutli-function button to play
/ pause music , short press Volume - /
previous music button for volume - and long
press for previous music . Short press
volume + / next music button for volume + &
long press for next music .
6 , Music automatically mute during
incoming call and convert to incoming call
tone , short press mutli-function button to
answer call , short press volume- to lower
down the volume and short press volume +
to increase volume .
Short press mutli-function button again for
end call , music will automatically restored .
7 , To answer another incoming call , you can
short press function button once to end
previous call , long press for 2or more
seconds to refuse this call .
Press the function button twice to maintain
previous call and answer this new call and
another button twice press allowing you to
revert to previous call .
4 ) Notice :
1 , Using the charging cable to charge
headset for 3 hours before first use or long
time not using to fully charge the headset .
During charging , the red indicating light is
up and light change to blue when headset is
fully charged .
Please be reminded that not to use the
headset during charging .
2 , Hang the headset at back side of your
neck and place the ear cups in front of ears at
jawbone position .
3 , Press function button twice to repeat last
call , long press 2 seconds to cancel dialing
call .
4 , If another call is on hold with the headset
during new call , you can short press function
button to end the new call to revert to the on hold
call .
5 , If your bluetooth device cannot search and
paired with BDS-662 in 1 minute , please power
off the headset , locate the headset close to your
device , power on the headset and search again .
6 , The bluetooth model only work with your
device support , for detail , please refer to the
attached manual .
7 , please enter password 0000 if request during
pairing .
8 , Suggest to charge the headset once a month if
it’s long time not in use .
9 , Headset will disconnect if headset is in position
10 meters or more apart from your device and will
reconnect when it’s back in transmission range , if
headset is more than 5 minutes disconnect with
device , it will automatically power off .
5 ) Accessories :
1 , Bluetooth headset ----1PCS
2 , USB-USB micro cable----1PCS
3 , Manual ----------1PCS
6 ) Specification :
Li battery ：3.7V/200mAh
Play time ：around 5 hours
Charging time : around 3 hours
Transmission range ：10 M
Speaker ：Bone conduction speaker
Sound level ：88dB
Microphone : -42dB
Frequency range : 100Hz-18KHz
Product weight ：49 grams
USB-USB micro cable length ：80cm
NOTE:This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
Thisdevicecomplieswithpart15oftheFCCrules.Operationissubjecttothefollowingtwo
conditions:
(1)thisdevicemaynotcauseharmfulinterference,and
(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycause
undesiredoperation.
Changesormodificationstothisunitnotexpresslyapprovedbythepartyresponsiblefor
compliancecouldvoidtheuser'sauthoritytooperatetheequipment.
Other Badasheng Headset manuals
