Badger Basket Elegance 00830 User manual

4.0B/0707/TG
PRODUCT NAME:
Elegance™ Round OR Elite™ Oval
Baby Bassinet with Bedding
PRODUCT MODEL NUMBERS:
Visit us online at www.badgerbasket.com
Toll-Free Customer Service: 1-800-236-1310 (Monday to Thursday 7:30 AM-4:30 PM CST)
Web: http://www.badgerbasket.com/parts • E-mail: p[email protected]
PLANT AND GENERAL OFFICE: PO Box 227, Edgar, WI 54426-0227 • Phone: [phone] • Fax: [phone]
CORPORATE OFFICE: 111 Lions Dr., Suite 220, Barrington, IL 60010
Page 1 of 5
BABY BASSINET
ASSEMBLY INSTRUCTIONS
Adult Assembly Required.
Save these instructions for future use.
ELEGANCE™ MODEL #’s:
00825 - Black Frame with Sage Waffle 00826 - Black Frame with Ecru Waffle
00827 - White Frame with White Eyelet 00829 - Cherry Frame with White Eyelet
00830 - White Frame with Ecru Waffle 00831 - White Frame with Sage Waffle
00832 - White Frame with Sage Toile 00836 - White Frame with Pink/White
00835 - White Frame with White/Sage Gingham 00837 - White Frame with Blue/White
00838 - Black Frame with Black Toile
ELITE™ MODEL #’s:
00855 - Natural Frame with Ecru Waffle
00856 - Cherry Frame with White Eyelet

4.0B/0707/TGPage 2 of 5
TOOLS NEEDED:
Phillips Screwdriver*
Hammer
* Power screwdriver is helpful but
be careful not to damage the bassinet
PARTSAND
HARDWARE:
(A) 2 - End Panels
(B) 2 - Rails
(C) 4 - Long Bolts
(D) 1 - Shelf
(E) 4 each -
Wheels, Knobs, Bolts
(F) 4 - L-Brackets
(G1) 8 - Medium Bolts
(G2) 8 - Short Bolts
(H) 1 - Bassinet Body
(not shown)
(I) 1 - Fabric Skirt
(J) 1 - Curved Canopy Pole*
(not as shown)
(K) 1 - Canopy Frame
(L) 1 - Fabric Canopy
(M) 1 - Fabric Bumper
(N) 1 - Fitted Fabric Sheet
(O) 1 - Mattress(not shown)
PARTSAND HARDWARE:
BEFORE YOU BEGIN ASSEMBLY:
Check all parts and hardware listed. If anything is missing, please
DO NOT call the store or return the product to them. Contact us for assistance. Most
problemsareresolvedwithout you needing toleavehome.Whenemailingor calling us,
pleasehavethis instructionmanualand yourproductmodel numberready.
For faster service, go to http://www.badgerbasket.com/parts
Ex4
Cx4
G1x8
Hardware not shown to scale
Ex4
Ex4
Fx4
G2x8
Ax2
Bx2
Dx1
Ix1
* Part J is curved.
* It is not straight as shown.
Jx1*
Kx1
Lx1
Mx1 Nx1

4.0B/0707/TGPage 3 of 5
NOTE: Elegance™Round models should be assembled in the room where
you intend to use it unless your doorways are wider than 33” (83.8 cm).
These assembly instructions cover both Elegance™ROUND bassinets and Elite™OVAL
bassinets. The shape of the units is different but the parts and assembly steps are identical.
STEP 2: See PICTURE 2A (this page) and 2B (on page 3).
Locate the FOUR L-BRACKETS (F), EIGHT MEDIUM
BOLTS (G1), and EIGHT SHORT BOLTS (G2) so you can
bolt the BASSINET BODY(H) to the BASSINETSTAND.
This step is easier if you put the bassinet body upside down,
and then put the bassinet stand upside down on top of the
bassinet body as shown in PICTURE 2B.
Line up the four pairs of holes on the END PANELS (A)
with the four pairs holes on the BASSINET BODY (H).
PositiontheL-BRACKETS(F)onthe inside and secure them
using the EIGHT MEDIUM BOLTS (G1) for the end pan-
els, and the EIGHT SHORT BOLTS (G2) for the bassinet
body.
WARNING !
Once the bassinet stand is
assembled, do not disassemble
and reassemble for future use.
Doing so may affect the
stability and safety.
PICTURE 1B
A
B
A
DB
PICTURE 1A
STEP 1: See PICTURES 1A and 1B
First, securely attach ONE CASTER WHEEL (E) to each leg of the END PANELS (A)
using ONE BOLT (E) and ONE KNOB (E) for each WHEEL (E). The knobs go on the
inside. The square hole on the wheel goes on the outside so the head of the bolt will “lock”
into the hole.
Next take ONE END PANEL (A) and attach the TWO RAILS (B) using TWO LONG
BOLTS (C). The grooves face inwards. Slide the SHELF (D) into the grooves with the
white warning label facing up. Then attach the second END PANEL (A) to the TWO
RAILS (B) using TWO LONG BOLTS (C).
PICTURE 2A
H
A
G2
G1

4.0B/0707/TGPage 4 of 5
STEP 3: See PICTURE 3.
With the bassinet in its correct, upright position, wrap the FABRIC
SKIRT (I) around the lower rim of the BASSINET BODY (H)
pressing the grip tape strips together as you go around. Begin and
end at the rear center where the metal spindle is located (the ends
may overlap).
STEP 4: See PICTURE 4.
There are two holes in the metal spindle on the bassinet body to
height adjust the canopy. Insert the METAL CANOPY POLE (J)
into the metal spindle on the bassinet body (H) and line up a hole
on the metal spindle with the push button on the canopy pole. Make
sure the push button snaps into the hole.
STEP 5: See PICTURE 5.
Insert the two free ends of the CANOPY FRAME (K) into the top
of the CANOPY POLE (J). Tap gently with a hammer until the
ends of the frame are fully seated inside the pole.
Next,placetheFABRIC CANOPY(L)ontotheCANOPYFRAME
(K) and secure it to the frame with the ribbons and/or the grip tabs
provided.
I
H
PICTURE 3
PICTURE 2B
H
A
A
J
Pushbutton
on canopy
pole (J) must
snap into the
hole on the
metal spindle.
PICTURE 4
PICTURE 5
J
K
F

4.0B/0707/TG
•SUFFOCATION HAZARD - Infants can suffocate:
»in gaps between an extra pad and the side of the bassinet,
»on soft bedding.
NEVER add a mattress, pillow, comforter, or padding. Use ONLYthe pad
and/or bedding provided by the manufacturer. If a sheet is used with the pad,
use only the one provided with the bassinet or one that is from Badger Basket
Company or one that is specifically designed to fit the dimension of the the
mattress provided.
• TO REDUCE THE RISK OF SIDS: pediatricians recommend that healthy
infants be placed on their backs to sleep, unless otherwise advised by your
physician.
• DO NOT move or carry the bassinet with your baby inside of it.
• DO NOT allow other children or pets to climb into or onto the bassinet when
your infant is inside.
• DO NOT attach or place toys with strings in or around the basket. Strings can
cause strangulation or choking.
•Keep bassinet away from stoves, heaters, camp fires/flames, fireplaces, stairs, open windows, window blinds, running or
standing water, and any other hazard which could cause injury to your baby.
• NEVER use plastic bags inside the basket such as to cover the mattress.
• Bassinet should always be placed on a firm, flat surface. It should never be placed near stairs or on tables or elevated
surfaces.
Page 5 of 5
Check ALL OF THE HARDWARE to make sure everything is fully tightened. Carefully review the safety
informationbelow.NOTE: Your bedding and canopy may vary in color, pattern, and/or style from what is shown here.
CARE INSTRUCTIONS: Wipe bassinet clean with a damp cloth and mild detergent as needed. Bedding can be
machine washed on cold, gentle cycle, and air dried or tumble dry on low or no heat. Iron on lowest setting for poly/
cotton. Secure all grip tabs together before washing so they do not catch on the bedding or ribbons.
M
N, O
PICTURE 6
STEP 6: See PICTURES 6 and 7.
Position the FABRIC BUMPER (M) inside the BASSINET
BODY (H). Position and then secure the tabs on the bumper to
the thicker dowels and tie the ribbons, and then tie the remain-
ing ribbons to the thinner dowels.
NOTE: Be sure the bumper is secured and check the rib-
bons regularly to make sure they stay tied. Loose bedding
can be a danger to your baby.
Put the FABRIC FITTED SHEET (N) onto the MATTRESS
(O) and place them inside the bassinet. Additional sheets are
sold separately! Contact us or check our web site for more in-
formation or to find a retailer.
FALL HAZARD: To help prevent falls, please note this
bassinet is a safe place for your newborn to sleep until Baby is
4 months old, 20 lbs. (9.09 kg), OR when Baby can push up,
roll over, or crawl - whichever limit comes first.
PICTURE 7
WARNING - FAILURE TO FOLLOW
THESE WARNINGS AND THE
INSTRUCTIONS COULD RESULT
IN SERIOUS INJURY OR DEATH: