Badger Basket ENVEE II User manual

ENVEE II™ HIGHCHAIR
WITH PLAYTABLE
CONVERSION
* Actual chair
may vary slightly from shown
Assembly Instructions. Adult Assembly
Required. Read all instructions before use.
This manual is part of the product and
must be kept for future reference.
MODEL NUMBER*:
93701 - Gray/Green
93702 - Gray/Chevron
93703 - Charcoal/Teal
93704 - Pink/White
93705 - Blue/Orange
VERSION CODE*:
3.0/0421/TG
FOR REPLACEMENT PARTS:
http://www.badgerbasket.com/parts
•Assembly Videos available on YouTube
•
Badger Basket®, PO Box 227, Edgar, WI 54426-0227 USA • Web: www.badgerbasket.com
U.S. Based Customer Service Toll-Free (Mon-Thurs 7:00 AM-4:00 PM CST): 1-800-236-1310
Phone: [phone] • Fax: [phone]

READ ALL INSTRUCTIONS before use of this product. Keep instructions for future use. Use only the parts and
hardware provided by Badger Basket®. Do not use the product if it is damaged, broken, or missing parts. Hardware
may include small parts. Choking Hazard! Keep unassembled parts out of the reach of small children. DO NOT allow
anyone to climb, stand on, or play on or inside of this product. It is not a step stool or ladder. Periodically check to
make sure all the screws remain tight. It is recommended that the high chair be used in the upright position only by
children capable of sitting upright unassisted. This is usually around six (6) months of age. PREVENT SERIOUS
INJURY OR DEATH FROM FALLS OR SLIDING OUT. Your child MUST ALWAYS be secured with the 5-point seat
harness regardless of child’s age and reclined/upright position of the seat. The tray is not designed to hold the child in
the chair. ALWAYS keep your child in view while in the chair. NEVER leave your child unattended, not even for “just a
minute”. DO NOT make adjustments to the seat height or upright/recline position while child is in the chair. No product
or a heating appliance such as electric or gas heaters.
WARNING - FAILURE TO FOLLOW THESE
WARNINGS AND THE INSTRUCTIONS COULD
RESULT IN SERIOUS INJURY OR DEATH
USE AND CARE INSTRUCTIONS:
Wipe plastic parts with a damp cloth and mild soap as needed. Seat pad can be machine washed, cold water gentle cycle; air
dry only. Do not tumble dry or iron! Seat pad may be dry cleaned. Insert feeding tray (PART O) is dishwasher safe.
BEFORE YOU BEGIN ASSEMBLY:
Check all parts. If anything is missing or not satisfactory,
please DO NOT call the store or return the product to them.
Please go online to: http://www.badgerbasket.com/parts
Most problems are resolved without you needing to leave home.
When emailing or calling us, please have this instruction manual,
your product model number, and your Version Code ready.

G×1
A×1
B×1
E×1
C×2 D×4
N×1
K×1
O×1
L×1
J×1
H×1
I×1
F×1
ASSEMBLY TOOL
CHAIR LEFT SIDE
SEAT ASSEMBLY
WITH PAD AND 5PT HARNESS
CHAIR RAIL
CHAIR RIGHT SIDE
TABLE CAP
TABLE RAIL
TABLE LEFT SIDE
TABLE RIGHT SIDE
TABLE TOP
SEAT BOLT
M×20P×2
BOLT
T-BAR MAIN TRAY
INSERT TRAY
FRONT FEET

1
B
L
STEP 1: Connect the SEAT BOTTOM (B) to the SEAT BACK (B).
Secure the belt for the SEAT PAD (B).
Fully insert the SEAT BOLT (L) through the hinge on the SEAT ASSEMBLY (B).

2
F
E
M
C
STEP 2: Insert the SEAT ASSEMBLY (B) into the corresponding holes on the CHAIR RIGHT SIDE (F).
Insert the TWO CHAIR RAILS (C) into the corresponding holes on the CHAIR RIGHT SIDE (F).
The Chair Rails will insert only one direction (match up the shape of the holes).
Attach the CHAIR LEFT SIDE (E) to the SEAT ASSEMBLY (B) and TWO CHAIR RAILS (C).
Secure the CHAIR LEFT SIDE (E) using SIX of the BOLTS (M). Be sure BOLTS (M) are twisted to
tighten them properly using the ASSEMBLY TOOL (A).
REPEAT WITH SIX BOLTS (M) FOR THE CHAIR RIGHT SIDE (F)!
M
A
B
B
C
C
C
F

REPEAT WITH FOUR BOLTS (M) FOR THE TABLE RIGHT SIDE (I)!
3
M
I
J
H
G
MA
G
STEP 3: Insert the TABLE TOP (J) into the corresponding holes on the TABLE RIGHT SIDE (I).
YOU MUST MATCH UP THE D1 and D2 INDICATORS THAT ARE MOLDED INTO THE PLASTIC PARTS.
Insert the TABLE RAIL (G) into the corresponding holes on the TABLE RIGHT SIDE (I).
The Table Rail will insert only one direction (match up the shape of the holes).
Attach the TABLE LEFT SIDE (H) to the TABLE TOP (J) and TABLE RAIL (G).
YOU MUST MATCH UP THE D3 AND D4 INDICATORS THAT ARE MOLDED INTO THE PLASTIC PARTS.
Secure the TABLE LEFT SIDE (H) using FOUR of the BOLTS (M). Be sure BOLTS (M) are twisted to
tighten them properly using the ASSEMBLY TOOL (A).
I

4
NOTE: The leg and table posts are marked with
"F" for Front and "B" for Back to help you align them properly.
STEP 4: CHAIR connects securely to the TABLE at
each of the four legs, as shown here. You will hear an
audible "click" to indicate the parts are properly connected together.
Gently tug upwards on the chair to be sure all four legs are properly
connected.
Buckle your child into the seat using the 5-Point Harness. Snap the shoulder/waist
Remember that the harness MUST ALWAYS be used, and never leave child unattended in the chair!
straps to the buckle on the crotch strap. You will hear the buckles "click" to indicate
they are securely fastened. Gently tug on the harness to be sure it's properly fastened.
P
P
Snap the FRONT FEET (P) onto the
front legs (H, I). Be sure the tabs on the table
legs lock securely into the slots on the feet.

position. Gently tug the seat back to be sure
5
K
N
O
STEP 5: Snap the T-BAR (K) into place on the MAIN TRAY (N).
Pull to release the tray latches on both sides of the MAIN TRAY (N), slide the tray
into place on the CHAIR SIDES (E,F), and then release the latches. You have a choice
of three positions for the MAIN TRAY. You will hear an audible click to indicate
the tray is locked into position. Gently tug the tray to be sure it's securely locked in place.
Snap the INSERT TRAY (O) onto the MAIN TRAY (N). The INSERT TRAY (O) can be
removed and reattached anytime as needed.
3 POSITIONS
To recline the seat, press and hold the
latch on the rear of the seat, and push
the seat back forwards or backwards
as needed. You have a choice of
three positions. When you release the
latch, you will hear an audible
"click" to indicate it has locked into
it's securely latched in position before
putting your child into the seat.

STEP 6: To convert the HIGHCHAIR to a TABLE AND CHAIR, first remove the tray,then push in
6
D
D3
D4
D1
D2
the release
buttons on the chair legs and pull up on the chair to separate it from the table.
Next use the FOUR TABLE CAPS (D) to cover the connecting posts on the table.
The caps and table posts are permanently marked to help you align them properly (D1, D2, D3, and D4)

7Follow these diagrams for removing/attaching the seat pad as needed for cleaning
and maintenance. These diagrams show how to unbuckle and remove the harness belts and
remove the pad, and then reverse the process for putting it together again.
12
7
34
5
6
8