Bagel Labs PIE 002 User manual

BAGEL-002(PIE SMART TAPE MEASURE) User Guide V 1.1
1. PIE: Smart Tape Measure for Your Body
PIE is the first smart tape measure dedicated to helping people measure accurate body sizes. It helps
you easily measure various parts of the body and keep track to improve your health and fitness.

2. Getting Started

3. Safety Warnings
A. Please read all instructions. Failure to follow any instruction listed below may result in electric
shock, fire, choking and/or serious injury.
i. DO NOT use this device for any purpose other than outlined in this manual.
ii. DO NOT disassemble / modify the device. There are no user serviceable parts inside.
iii. DO NOT subject the device to extreme conditions: extreme temperatures beyond
operating temperatures, high vibrations, dusty area, humid conditions (including any liquid)
or direct sunlight.
iv. DO NOT use excessive force to the tape or the gear. Stretching the tape or grinding the
gear can damage the device permanently.
v. DO NOT fold or twist the tape. This can damage the tape permanently.
vi. DO NOT use excessive force to pull the tape over 150 cm / 59 in. This may permanently
damage the device.
vii. Be very careful when measuring neck circumference. The fiberglass tape may accidentally
cause choking.

4. Regulatory Information
A. You can check the device’s regulatory information on its e-label, which can be accessed by
following these steps below.
Step 1. Connect a power source with micro USB to start charging the device’s battery
Step 2. Press the [Save Button] for 2 seconds
Step 3. Toggle through e-label pages by pressing the [Save Button]
B. This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
5. Limited Warranty
A. Thank you for purchasing a Bagel Labs product.
B. This product was manufactured under strict quality assurance and inspection standards by
Bagel Labs. This warranty is effective for 1 year from the date of purchase. Products with
defects within the warranty period needs to be returned to be (i)replaced with a new product
free of charge, or (ii)refunded, at our discretion.
C. Exclusions from warranties:
i. if the device was not purchased from Bagel Labs or Bagel Labs certified dealers
ii. if the device was modified or disassembled
iii. if the device was not treated with the above instructions
iv. if the device had taken more than 10,000 measurements.

6. Operating Specifications
Voltage Input 5V DC
Display 0.96” OLED (128x64)
Battery 400mAh Li-Po
Connectivity Bluetooth Low Energy 4.2
Materials
Polycarbonate (Housing)
Polyoxymethylene (Gear)
Fiberglass (Tape)
Compatible OS iOS, Android
Measurement
Range 2 - 150 cm, 1 - 59 in
Unit mm, cm, in
Resolution 1 mm, 1/16 in
Accuracy ±1mm, ±1/32 in
Firmware Update Over the Air Firmware Update

FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to correct the interference by
one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate this equipment. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.

Contact
For more information, please visit our website or email us to the following address:
https://www.bagel-labs.com
[e-mail]
Designed by Bagel Labs
Made in Korea
Copyright 2018 Bagel Labs. All Rights Reserved.