Bake Max DOUGH MOULDER User manual

OPERATION MANUAL FOR DOUGH MOULDER
1. INSTALLATION
Dough Moulder has 4wheels and can be easily moved around.
You will only have to connect the electric power supply to it according to
nameplate. The Moulder is ready for start up and operation.
2. OPERATION
（1）Loosen the two dough feed guide knob and move the dough feed guide
on both sides to the right position according to the weight of the dough and
tighten the dough feed guide knob again. The position of dough feed guide
should be so adjusted the dough feed guide should not touch the dough.
（2）Adjust the top roller and bottom roller gap by the corresponding knob. The
gap should be close enough to squeeze out the air inside the dough and get
the required diameter and length of the dough piece after molding. But the gap
should not be too small to damage the surface of the dough.
（3）Check whether the position of curling wire mesh is alright. Adjust it in
case the dough rolling up is too loose or too tight.
（4）adjust the position of presser board to presser board to press the dough
piece to the right tightness and to the right length.
1

PRESSER BOADR
MAIN SWITCH
DOUGH FEED
GUIDE KNOB
DOUGH FEED GUIDE
GURLING WIRE MESH
TOP ROLLER GAP ADJ. KNOB
BOTTOM ROLLER
GAP ADJ. KNOB
2

DOUGH MOULDER
C/No DESCRIPTION Q’TY C/No DESCRIPTION Q’TY C/No DESCRIPTION Q’TY
1 BRACKET 1 41 POWER 1 81 PLATE 1
2 BRACKET 1 42 POLLER 1 82 SHAFT 1
3 ROLLER 3 43 POLLER SHAFT 1 83 BLET 1
4 ROLLER 1 44 SCREW ROD 2 84 CHAIN WHEEL 1
5 BEARING 8 45 HANDLE WHEEL 2 85 PLATE 1
6 SLIDE BLOCK 2 46 BELT PLATE 1 86 WASHER 4
7 SLIDE BLOCK 2 47 BELT 1 87 PIN 6
8 SPRING 4 48 PLATE 1 88 CHAIN WHEEL 1
9 ROD 3 49 PLATE 1 89 CHAIN WHEEL 1
10 SCREW ROD 2 50 CLASS 1 90 CHAIN 1
11 CHAIN WHEEL 4 51 PLATE 1
12 SCREW ROD 2 52 SPRING 4
13 CHAIN 2 53 PLATE 2
14 WIPPER 4 54 BLOCK 2
15 SPRING 2 55 SCREW ROD 1
16 SPRING 6 56 SCREW ROD 1
17 BLOCK 4 57 CHAIN 1
18 PIN 8 58 CHAIN 1
19 CHAIN WHEEL 1 59 CHAIN WHEEL 2
20 KEY 5 60 COVER 1
21 CHAIN 1 61 HANDLE WHEEL 3
22 ADJ PLATE 1 62 BRACKET 1
23 CHAIN WHEEL 1 63 NET 1
24 BEARING 1 64 SHAFT 1
25 SPRING 1 65 SHAFT 1
26 BEARING SET 2 66 CLASS 1
27 BEARING 6 67 COVER 1
28 CHAIN WHEEL 1 68 BELT ROLLER 1
29 BEARING 1 69 COVER 1
30 BEARING SHAFT 1 70 COVER 1
31 PLATE 3 71 COVER 1
32 CHAIN WHEEL 1 72 COVER 1
33 CHAIN WHEEL 1 73 PLATE 2
34 KEY 1 74 ROUND SCREW 2
35 CHAIN WHEEL 1 75 BEARING HOUSING 2
36 CHAIN WHEEL 1 76 SHAFT 1
37 KEY 1 77 BELT PULLEY 1
38 CHAIN 1 78 KEY 1
39 BASE 1 79 MOTOR 1
40 WHEEL 4 80 PULLEY 1
3

4

5

6