Q&A
Ⅴ
Time mode: The dial shows the time and date . (The time of the bracelet after
connecting the app will automatically synchronize with the time of the phone, and the
time cannot be set on the wristband)
Sports information: automatically record the number of steps per day, calories
Heart rate measurement: Switch the bracelet to heart rate measurement and press and
enter the heart rate interface to automatically measure the heart rate. The heart rate
displayed on the bracelet interface is the latest measured data.
Blood pressure measurement: The current point automatically measures the current
blood pressure. It can also be manually measured by APP. The wrist switch is switched
to the blood pressure interface and press to enter the measurement. The measurement
is automatically returned to the corresponding interface.
Blood oxygen measurement: The whole point automatically measures the current blood
oxygen condition, and can also be manually measured by APP. The wrist switch is
switched to the blood oxygen interface and the long press is pressed to start the
measurement. The measurement is completed and the corresponding interface is
automatically returned.
Sleep monitoring: automatic detection of daily sleep quality
Exercise mode: Press and enter in the exercise mode interface. There are three modes
of running, mountain climbing and riding. In each mode interface, you can start
recording the movement time and generate calories, tap the pause, and press and exit.
Smart reminder: Open the reminder on the APP. When there are APP, call, SMS and
other information on the phone, there is a corresponding prompt on the bracelet.
More: stopwatch (long press to enter, exit, tap start, pause), find the phone (long press
search, touch pause), power off (long press and turn off), reset function (long press to
return to time interface), 2D Code (scan the QR code into the APP download address).
Other functions: raise the hand to brighten, sedentary reminder, do not disturb mode,
shake a photo, point measurement, WeChat sports, apple health, automatic language
matching
Can't search for a bracelet or connect when binding?
Android system:
1.Please confirm that the mobile phone Bluetooth is turned on, and the Bluetooth logo is not
displayed on the wristband (if the Bluetooth ring is displayed on the wristband, it indicates that
it has been connected). Close to the bracelet, try searching and connecting again, and make
sure the phone system is Android4.4 or higher.
2.If you still can't connect, go to Phone Settings→Application Management→Authorization
Management→App Rights Management, find the application [WearFit], and mark all the permissions
as “Allow”; then enter the phone settings→GPS positioning to open the GPS location function of
the phone. , restart your phone and try to connect.
IOS system:
Please confirm that the mobile phone Bluetooth is turned on, and the Bluetooth logo is not
displayed on the wristband (if the Bluetooth logo is displayed on the wristband, it indicates that it
has been connected by other devices, please release the Bluetooth beforehand). After the Apple
mobile phone is connected once, if you turn on the mobile phone Bluetooth again, the Bluetooth
device will be connected by default, so you can go to the phone settings → Bluetooth → ignore
this device, the APP can detect the bracelet.
After the bracelet is bound, the display is not connected, or the connection is displayed but the
power is 0%?
At this point, the phone is not successfully bound to the bracelet. Please re-bind.
APP no data display?
In the main interface, pull down and refresh the data manually to display the data in the APP.
Automatically synchronizing data will only be synchronized when the phone's bracelet is first
connected, followed by automatic synchronization of data for each hour. In addition, the whole
point measurement should be turned on. Our column diagram of step counting, heart rate and
fatigue all read the whole point data. If it is not open, the histogram has no data.
After the APP pull-down is refreshed, the data does not load?
App Settings→Restore Bracelet Factory Settings→Click to restore factory settings→Button
Shutdown→Reboot the Bracelet to connect to the App. Normally use the bracelet and the data
can be loaded.
Is the bracelet time out of sync after connecting the phone?
Phone Settings → Application Management / Rights Management → App Permissions Open →
Relink Bracelet → App's main interface pull-down refresh
