Bakery Equipment AE-BS06 User manual

Bakery Equipment –AE-BS06 BREAD SLICER Owner’s Manual
AE-BS06 BREAD SLICER

Bakery Equipment –AE-BS06 BREAD SLICER Owner’s Manual
1. INSTALLATION
Be sure to put the Slicer on a stable table, making sure the Slicer seats firmly on
the table. If the Slicer vibrates seriously during operation, we recommend a
rubber pad to be put underneath the frame of the Slicer.
2. ELECTRIC CONNECTION
Before making electrical connections, check the specifications on the name
plate to make sure they agree with those of your electrical service.
3. SPECIAL ATTENTION
The operator should never put his fingers into the vibrating knives. If the piece
of last bread can not be sliced and removed easily, please do not try to push it
out with fingers from the chute or try to take it out form front.
Please disconnect the power source of the Slicer when you clean it.
4. CHANGE OF BLADES
It is an indication when Slicer slices the bread slowly, that of the blades have
become dull and should be changed.
TO DISMANTLE THE BLADES
1. Take off Cover front (9) and Top cover (19).
2. Take off Outgoing Chute (10).
3. Loosen the screws on Bracket (25) (26) and (40).
4. Take out Guide Rod (33) and the Frame for Blades (27) can be taken out.
5. Press Spring (30) to take out Blade one by one.
TO REMOUNT THE BLADES
1. Press Spring (30) to put the blades onto the Frame (27) one by one.
2. Put Frame (27) into position and insert the Guide Rod (33).
3. Tighten the screws on Bracket (25) (26) and (40).
4. Put in Outgoing Chute (10).
5. Mount the Cover front (9) and Top cover (19).

Bakery Equipment –AE-BS06 BREAD SLICER Owner’s Manual
The Parts List of Bread Slicer Machine
S. NO. Description Q’ty S. NO. Description Q’ty
1 Machine Wall (left) 1 2 Machine Wall (right) 1
3 Screw Nut 1 4 Handle 2
5 Fixed Lever 3 6 Plastic Lock Bolt 3
7 Division Plate Support Shaft 2 8 L Plate Fixed Block 1
9 Front Cover 1 10 Plate for Receiving Bread 1
11 Pressing Plate for Toast 1 12 Division Plate to Fixed Bread 1
13 Fixed Block 1 14 Fixed Rod for Knife Shelf 1
15 Ball Bearing 4 16 Acrylic Plate 2
17 Upper Slide Board 1 18 Slide Board Fixed Block 3
19 Rear Cover 1 20 Lock Bolt 4
21 Guide Bolt 2 22 Slide Bar Shaft 1
23 Slide Board Shaft 1 24 Slide Board Shaft 1
25 Main Shaft 1 26 Knife Shelf 1
27 Knife 31 28 Fixed Pin 31
29 Knife Blade Fixed Block 62 30 Spring 31
31 Tee Tube 1 32 Driving Shaft 2
33 Driving Rod Link 2 34 L Plate 2
35 Cable 1 36 Linking Bar Joint Block 1
37 Linking Bar Seat (left) 1 38 Shaft Bearing 6
39 Joint Bar 2 40 Bush 4
41 Linking Bar Seat (right) 1 42 Drive Pulley 1
43 Belt 1 44 Motor 1
45 Capacitor 1 46 Motor Seat (front) 1
47 Motor Seat (right) 1 48 Joint Pin 1
49 Drive Pulley 1 50 Drive Pulley 1
51 Screw Nut 1 52 Plastic Linking Rod 1
53 Live Axle 1 54 Switch Plate 1
55 Switch 1 56 L Plate 2
57 Circular Sticker 2 58 Motor Starting 1
Note: Quantities of No. 27,28,29,30 is changeable according to slice
thickness.