Banner Q106e User manual

Instructions to User
Product Specification
Model
Material
Front lock size
Rear lock size
Weight of lock
Door opening methods
Power supply
Supported door thickness
User capacity
Operating Temperature
Operating Humidity
Waterproof and dustproof grade
Q106e
Zinc alloy
65.4*163.4*31.5mm
72.4*188.4*45.5mm
1.35kg
Tuya APP/Password/
Fingerprint/Key
Four AA (5#) batteries
35-55cm
50 fingerprints,150 passwords
-30℃~+55℃
<RH 95%
IP65
Product Overview
Front View
Rear View
Keyboard
USB emergency power supply interface
Setting key
Knob
On/Off key
Front lock
wiring port
Battery cover
Battery
compartment
Screw hole
Fingerprint reader
Fingerprint LED
Cylinder
Cylinder
cover
Back key Confirm/Close key
Indicator
Accessories package
Parts List
1*Front lock
1*Rear Lock
1*Mounting Plate
1*Deadbolt
1*Strike Plate
4*Strike screws(M4*0.8 in)
2*Interior Assembly Screws (M4*0.4 in)
1*Interior Assembly Screw (M4*1 in)
1*Connection column screw (M4*1.5 in)
4*Mounting Plate Screw(M5*1.8 in/2.2 in)
1*Strike Reinforcer
3*Keys
3. If the door has been installed with a lock, remove it first,
including the bolts.:
25 mm
1" 1⅜" / 35 mm -
2 ⅛" / 55 mm
Door thickness
54mm
or
2⅛"
38mm
1½"
Backset
2⅜" / 60 mm
or 2¾" / 70 mm
1. Make sure the lock can be installed correctly
① There are no obstacles in the door opening, ensure that the lock
tongue can be extended and retracted normally.
② Compare the position of the hole in the door with the drill
template.
2.Door size
① Diameter of hole in the door (2 '' / 54 mm or 1½'' / 38 mm).
② Distance between the hole center to the door edge (2 '' / 60 mm
or 2¾'' / 70 mm).
③ Door opening diameter (1'' / 25 mm).
④ Door thickness (1 '' / 35 mm - 2 '' / 55 mm).
Preparations
Door parameters and specifications
01 02 03
Q106e Smart Lock User Manual
•Do not attempt to disassemble or repair the product without
authorization.
• Do not press the keyboard and fingerprint recognition area with
excessive force or sharp objects.
• Make sure the door is fully closed when going out. The
manufacturer is not responsible for any loss caused by your
improper door closing.
• Replace the battery when you hear the alarm of low battery.
• Change your password regularly to ensure security.
• Do not clean the device with corrosive substances to avoid
damaging the protective layer and affecting the smooth surface of
the device.
• Keep your fingers clean when unlocking with fingerprint.
• Please install inside the door or keep the door normally open to
avoid being locked outside the door.
• Keep the mechanical key in a safe and secure place. The
mechanical keys act as a backup, if your password.
• fingerprints or APP don't work, they can prevent you from being
locked outside the door.

Install the smart lock
Install the deadbolt
Deadbolt Strike screws
(M4*0.8 in) Screwdriver
① Measure the distance between the hole center to the door edge
(2'' / 60 mm or 2¾'' / 70 mm).
② If the distance between the hole center to the door edge is 2'' /
60 mm, please use the provided lock bolt for installation. If the
distance between the hole center to the door edge is 2¾'' / 70 mm,
adjust the deadbolt to 70mm until the bolt locks into place.
③ Insert the door bolt into the door frame, make sure the word
"UP" is facing up, and it is indicated on the lock bolt.
④ Screw the door bolt into the door frame with a screwdriver (not
provided).Items required: deadbolt, deadbolt screws, screwdriver
(not provided) - schematic diagram, operation diagram.
2-3/8 2-3/4
180°
Install the strike plate
If it is confirmed that the bumper plate (strike plate) used by the
lock bolt on the existing door frame can be extended and retracted
smoothly, you can skip this step without installing the strike plate
in the accessories package.
TOP
Upward
Strike Plate Strike Reinforcer
(optional)
Strike screws
(M4*0.8 in)
①Align the bumper plate (strike plate) and the strike plate buckle
box with the center hole of the lock bolt.
② Put the strike plate buckle box into the door hole. Putting this
accessory is for the sake of appearance and to avoid dust in the
door hole being brought into the cylinder by the lock bolt, which will
affect the life of the cylinder.
③ The strike plate covers the buckle box, and the strike plate is
fixed with screws. Make sure the strike plate is placed in the
correct position and direction.
Screwdriver
①Attach the black silicone pad to the back of the front lock (it has
been attached at the factory, please ignore this step).
② If the diameter of the door hole is 2"/54mm, please use the
provided spacer to secure the smart lock.
③ If the diameter of the transverse hole is 1½'' / 38 mm, please
remove the spacer.
④ Align the tail teeth of the cylinder with the center hole of the
lock bolt and insert it into the center hole.
⑤ Pass the wire connected to the front lock from under the electric
lock into the door.
Install the front lock part
1.Attach the black silicone pad to the mounting plate (it has been
attached at the factory, please ignore this step).
2.Pass the front lock wire through the hole in the mounting plate.
3.Secure the mounting plate to the inner door frame with the
mounting plate plate screws. Please confirm the door thickness,
use the corresponding screws, cylinder fixing 1.8 inch
screws(schematic diagram “J”) for door thickness of 35-45mm or
cylinder fixing 2.2 inch screws (schematic diagram “J”) for door
thickness of 35-55mm, make sure the screws pass through the
holes of the lock bolt and the mounting plate, and lock them in
place.
4.In order to secure the lock to the door, please use additional
auxiliary fixing screws (schematic diagram “I”), and drill according
to the drilling diagram (if you do not want to drill holes to damage
the smart lock, this step can be omitted).
Install the mounting plate
Mounting Plate
Mounting Plate Screw
(M5*1.8 in/2.2 in) Screwdriver
Connection column
screw (M4*1.5 in)
this step can be
omitted
04 05 06

1. Pull to open the wiring port cover(②), pass the front lock wire
through the rear lock, and insert the wire into the socket correctly.
2. It is necessary to ensure that the mechanical knob is in the
vertical position and the cylinder is in the retracted state. Align the
tail teeth of the cylinder with the cylinder hole on the rear panel
and insert it correctly.
3. Secure the rear lock to the mounting plate with screws.
4. Turn the knob and check whether the lock bolt can retract. If it is
unable to retract smoothly, adjust the screws or reinstall it again.
Note: If the lock bolt is inserted when the lock is not in the
retracted state and the mechanical knob in the vertical state, it will
cause the lock bolt to be abnormal, and the APP shows that the
On/Off state of the lock is inconsistent.
Install the rear lock
Interior Assembly Interior Assembly
Screws
①
②③
Install the battery
Insert four AA batteries into the battery compartment, note the
polarities (+/-).
1.When the smart lock is used for the first time (in the initialization
state), it is necessary to calibrate the door opening direction. After
starting the lock, you will hear the voice prompt: "Please turn the
knob to the horizontal position", after setting successfully, you can
start to use the smart lock. You can also press the Back key on the
keyboard to exit, and set later.
Enter the local program to calibrate the smart lock.
Smart lock local function
Calibrate Door Opening Direction
Note:
2.Calibrate the smart lock direction in the smart lock local menu
program:
① Hold the Back key to verify the administrator password
② When you hear the voice prompt "Please press 5 to calibrate the
smart lock direction", choose to modify the user.
③ When you hear the voice prompt: "Press 1 for door opening to
left, press 2 for door opening to right, choose the door opening
direction.
④ Calibrate successfully.
It will cause the lock bolt to be abnormal and the smart lock
cannot be used correctly if the door opening direction is not
calibrated. Please calibrate the door opening direction.
Left-handle Right-handle
Add fingerprint:
① Hold the Back key to verify the administrator password.
② When you hear the voice prompt "Please press 1 to add user",
please press 1 to add user.
③ When you hear the voice prompt: "Please press 2 to enter
fingerprint", please press 2 to enter fingerprint.
④ Repeatedly enter the fingerprint 6 times, the fingerprint is
added successfully.
Note: Enter your finger in as many places as possible to improve
the door opening experience via fingerprint recognition.
Add local administrator
1.Before add local administrator, the smart lock will be in the
initialization state, and it can be opened with any fingerprint or
password"123456".
2.Only one administrator for each smart lock, it must be 6-8
digitals passcode.
3.Operation as below:
Add user
Two types of users, password or fingerprint.
Add password:
① Hold the Back key to verify the administrator password.
② When you hear the voice prompt "Please press 1 to add user",
please press 1 to add user.
③ When you hear the voice prompt: "Please press 1 to enter the
password", please press 1 to enter password.
④ Enter a 6-8-digit password, press the Confirm button to end,
and enter it again, the password is added successfully.
Operation
“ "
07 08 09
tail teeth
Hold the key
Enter a 6-8 digit password and press the Confirm key
Enter the password again and press the Confirm key
Added successfully

Delete user
1.It can only modify the ordinary user password, the administrator
password cannot be modified.
2.Modify the password in the smart lock local menu program:
① Hold the Back key to verify the administrator password.
② When you hear the voice prompt "Please press 1 to modify the
user", please press 1 to modify the user.
③ When you hear the voice prompt: "Please enter the original
password", enter the original password and press the Confirm key
When you hear the voice prompt: "Please enter a new password",
please enter the new password and press the Confirm key.
⑤ When you hear the voice prompt: "Please enter the new
password again", please enter the new password and press the
Confirm button.
⑥ Password is changed successfully.
Change password
1.Perform toggle volume of the smart lock in the local menu
program.
Hold the Back key to verify the administrator password.
When you hear the voice prompt "Press 6 to toggle the volume",
please press 6 to toggle the volume.
When you hear the voice prompt: "Press 1 for high tone, press 2 for
medium tone, press 3 for low tone, press 4 for mute", please select
the volume accordingly.
Toggle volume
1.Enable the normally open mode in the smart lock local menu
program.
① Hold the Back key to verify the administrator password.
When you hear the voice prompt "press 7 for normally open mode",
please press 7 to select the normally open mode.
③ When you hear the voice prompt: "The lock is normally open",
the operation is successful.
Disable the normally open mode:
① Unlocking once with an electronic key, the mode will be released
after automatic locking.
② Disable the normally open mode (Confirm key of the keyboard,
one-click On/Off key, mechanical knob).
Normally open mode
Restore factory settings: delete all smart lock usage data, reset
the smart lock to the factory state (please use this function with
caution, it will not be restored after operation).
1.Initialize the settings in the smart lock local menu program
Hold the Back key to verify the administrator password
When you hear the voice prompt "press 8 to initialize the settings",
please press 8 to initialize the settings.
③ When you hear the voice prompt: "Press the Confirm key to
confirm", please press the Confirm key to confirm and start the
initialization.
④ When you hear the voice: "Initialization successful", that is, the
lock is successfully initialized.
You can add other numbers before and after entering the correct
password in the lock. The total length of the virtual password is 16
digits.
Trial-and-error alarm.
After the smart lock fails to unlock multiple times, it will generate
an alarm and lock the smart lock for 180sTrigger: If wrong .
Restore factory settings
Virtual password
FAQ
1. What is the difference between administrator and normal user?
The administrator is the person who is originally registered in the
smart lock. The administrator can control all settings and functions of
the smart lock. Ordinary users can only unlock through fingerprints,
passwords or APP, and cannot set the smart lock.
2. The device is out of power, how to start it in an emergency ?
After powering through the emergency charging port (5V-1A) under
the front lock, enter the registered password or fingerprint to unlock,
or directly unlock with the mechanical key.
3. What should I do if I forget the administrator password?
You can log in to the Tuya APP to change the administrator password
in the Password Management, or briefly describe the problem and
send it to our official E-mail [e-mail].
4. What should I do if the smart lock system is locked?
Use the correct electronic key to open the door once
5.Why can't I open my door through the App from far away?
It may be affected by various factors such as obstacles to unlock with
the APP. It is recommended to keep the phone as close to the door as
possible, or at least within 16 feet.
Shenzhen Fingerchip Intelligent Technology Co., Ltd.Room 406-407,
Research Building, Tsinghua Hi-Tech Port, Nanshan District,
Shenzhen.
① Hold the Back key to verify the administrator password.
② When you hear the voice prompt "Press 1 to delete a user",
please press 1 to delete a user.
③ When you hear the voice prompt: "Please press 1 to delete all
user passwords, please press 2 to delete all user fingerprints, and
please press 3 to delete all users”.
① Select the key you want to delete, and the operation is
successful after hearing the prompt.
⑤ Delete user successfully.
10 11 12
Pair Your Phone with Smart Lock
Download the Tuya App from the App Store or Google Play
1.After downloading the APP, please register an account to use the
APP.
2.When pair the smart lock with your mobile phone, please be near
the smart lock to avoid pairing failure.
3.When pairing the smart lock, please keep the smart lock in
networking mode.
① Open the APP, select "Add Device", the APP will automatically
search for the smart lock in the networking mode.
② Press the 3+Confirm key on the smart lock to verify the
administrator and enter the networking mode, and when you hear
the smart lock voice prompt: "Please bind the smart lock with
mobile phone", it means that the smart lock has entered the
networking mode. Or enter the networking mode from the local
menu.
③ Select the searched smart lock.
④ When you hear the voice prompt: "Add successfully", that is, the
mobile phone and the smart lock have been successfully paired.
-20-
password is input continuously within 180s, the password pad will
be locked, if it fails to unlock continuously with fingerprint,
fingerprint recognition will be locked. Release: After unlocking
once with the correct electronic key, trial-and-error alarm will be
released.
Automatic locking
After the smart lock is opened, the smart lock will be automatically
closed within a fixed time (5S). After binding the APP, the locking
time can be adjusted and the automatic locking function can be
disabled.
Low battery alarm
The smart lock will issue a warning when the battery is low, please
replace the battery in time. The door can be unlocked about 50
times when the battery is low.
If the lock bolt is stuck when extended and retracted, the smart
lock will give alarm.
External power supply
When the smart lock is out of power, it supports an external USB
(5v, 1A) power supply to supply power to the smart lock. This
function cannot be used for charging and can only be used
temporarily.
User capacity
250 users in total, 100 fingerprints, 150 passwords.
Hold the Setting key restore factory settings
Toggle volume
333+Confirm key
7+Confirm key
51+Confirm key
123+Confirm key
3+Confirm key
Hold the Back key
Enable sleep quickly
Enter the local program
Networking mode
After unlocking, enter 123+Confirm key
to enable the normally open mode
Calibrate the door opening direction
Change user password
Return key Return or clear all entered information
Key operation list
Double click the Return
key 2 times

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority
to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.
Radiation Exposure Statement
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum
distance of 20cm from your body.