Baoding Longer Precision Pump WT3000-1FB User manual

WT3000-1FB Gear Pump Drive
Baoding Longer Precision Pump Co.,Ltd.
WT3000-1 B
Micro Gear Pump Drive
F
Operating Manual
BaodingLongerPrecisionPumpCo.,Ltd.
Building A, Chuangye Center Baoding National
High-Tech Industrial Development Zone
Baoding, Hebei, China 071051
TEL: [phone]
FAX: [phone]
E-mail: [e-mail]
Http //www.longerpump.com:
,

Table of Contents
2
3
4
5
5
5
6
6
6
7
7
7
Instruction
Basic Operation
Running Interface
Menu Navigation Diagram
Pump Head Operation
Flow Mode Operation
Dispensing Mode Operation
External Control
Maintenance
Technical Specifications
Pump Head Installation
Pump Head Flow Rates
Pump Head Setting
Enter Flow Mode
Flow Control
Flow Calibration
Flow Mode Operation Procedure
Enter Dispensing Mode
Dispensing Volume
Copy No.
Flow Rate Setting
Pause Time
Dispensing Calibration
Dispensing Mode Operation Procedure
External Enable Setting
Analog Signal Control
Footswitch Control
Communication Control Mode
External Control Output
1
Important Information:
Please read operating manual carefully before operation.
Warning:
To prevent damage to pump, do not run the pump dry.
If the power line or the plug are worn or damaged please pull out
the plug (Hold the plug not the power line when pulling out).
Please shut down the power supply and pull out the plug when you
think the pump needs to be maintained or repaired.
Shut down the power supply of the pump when connecting to
external control equipment.
The International Protection rating of this pump is IP31. Do not let
liquid enter this pump drive.
Warranty:
The warranty period of this product is one year. If repair or
adjustment is necessary within the warranty period, the problem
will be corrected at no charge if it is not due to misuse or abuse on
your part, as determined by the manufacturer. Repair costs out
side the warranty period, or those resulting from product misuse or
abuse, may be invoiced to you.
Contact Longer Company or Longer’s dealers before returning
pump to repair.
Adopt original carton or reliable package when returning pump to
repair.
Write a note on detailed description of failure phenomena and
contact information and put this note along with pump before
returning pump to repair.
Micro Gear Pump Drive Operating Manual
5
6
7
8
8
8
9
9
10
10
12
13
13
10
11
13

Table of Contents
2
3
4
5
5
5
6
6
6
7
7
7
Instruction
Basic Operation
Running Interface
Menu Navigation Diagram
Pump Head Operation
Flow Mode Operation
Dispensing Mode Operation
External Control
Maintenance
Technical Specifications
Pump Head Installation
Pump Head Flow Rates
Pump Head Setting
Enter Flow Mode
Flow Control
Flow Calibration
Flow Mode Operation Procedure
Enter Dispensing Mode
Dispensing Volume
Copy No.
Flow Rate Setting
Pause Time
Dispensing Calibration
Dispensing Mode Operation Procedure
External Enable Setting
Analog Signal Control
Footswitch Control
Communication Control Mode
External Control Output
1
Important Information:
Please read operating manual carefully before operation.
Warning:
To prevent damage to pump, do not run the pump dry.
If the power line or the plug are worn or damaged please pull out
the plug (Hold the plug not the power line when pulling out).
Please shut down the power supply and pull out the plug when you
think the pump needs to be maintained or repaired.
Shut down the power supply of the pump when connecting to
external control equipment.
The International Protection rating of this pump is IP31. Do not let
liquid enter this pump drive.
Warranty:
The warranty period of this product is one year. If repair or
adjustment is necessary within the warranty period, the problem
will be corrected at no charge if it is not due to misuse or abuse on
your part, as determined by the manufacturer. Repair costs out
side the warranty period, or those resulting from product misuse or
abuse, may be invoiced to you.
Contact Longer Company or Longer’s dealers before returning
pump to repair.
Adopt original carton or reliable package when returning pump to
repair.
Write a note on detailed description of failure phenomena and
contact information and put this note along with pump before
returning pump to repair.
Micro Gear Pump Drive Operating Manual
5
6
7
8
8
8
9
9
10
10
12
13
13
10
11
13

Micro Gear Pump Drive Operating Manual
Instruction
Acceptable pump heads for WT3000-1FB are MG204, MG209 and
MG213. The pump delivers flow rates from 83 to 2750 mL/min and
dispensing volume is from 0.1 mL to 999 L. Combining 128 32 LCD
display with membrane keypad and rotary coded switch makes the
operation easy and prompt. The speed can be adjusted manually or
automatically through external control interface.
1 2
Basic Operation
Run Key
In stop state, press , the pump starts to run.
In non-prime state, press , the pump stops.
When the pump is in flow rates mode state (the pump runs or stops) or in
dispensing mode (the pump stops), press the to enter prime
state when the pump runs at full speed for empting, filling and rinsing
operation; Press the again to return to common state. In prime
state, other keys are invalid.
Function 1: Cancel current operation and return to previous menu.
Function 2: In dispensing mode, press to switch different
dispensing parameters display.
Run Key
Stop Key
Prime Key
Prime Key
Exit Key
Stop Key
Prime Key
Micro Gear Pump Drive Operating Manual
Drive
Pump Head
External Control Output Interface
External Control Input Interface
Power Socket
Fuse Holder
Fan
Reference:
Refer to page 10 to know the functions of External Control.
LCD Display
Knob
Exit Key
Prime Key
Run Key
Stop Key
Power Switch
Pump Head Connecting Board
Exit Key

Micro Gear Pump Drive Operating Manual
Instruction
Acceptable pump heads for WT3000-1FB are MG204, MG209 and
MG213. The pump delivers flow rates from 83 to 2750 mL/min and
dispensing volume is from 0.1 mL to 999 L. Combining 128 32 LCD
display with membrane keypad and rotary coded switch makes the
operation easy and prompt. The speed can be adjusted manually or
automatically through external control interface.
1 2
Basic Operation
Run Key
In stop state, press , the pump starts to run.
In non-prime state, press , the pump stops.
When the pump is in flow rates mode state (the pump runs or stops) or in
dispensing mode (the pump stops), press the to enter prime
state when the pump runs at full speed for empting, filling and rinsing
operation; Press the again to return to common state. In prime
state, other keys are invalid.
Function 1: Cancel current operation and return to previous menu.
Function 2: In dispensing mode, press to switch different
dispensing parameters display.
Run Key
Stop Key
Prime Key
Prime Key
Exit Key
Stop Key
Prime Key
Micro Gear Pump Drive Operating Manual
Drive
Pump Head
External Control Output Interface
External Control Input Interface
Power Socket
Fuse Holder
Fan
Reference:
Refer to page 10 to know the functions of External Control.
LCD Display
Knob
Exit Key
Prime Key
Run Key
Stop Key
Power Switch
Pump Head Connecting Board
Exit Key

Knob
Function 1: Turn the to adjust the flow rates in flow rates display state.
Function 2: Turn the to select the menu and set the parameters, press
for confirmation in menus selection state.
Turn on or off the pump.
Knob
Knob
Knob
Power Switch
Running Interface
Turn on the pump, the pump is initialized first and select the language.
Chinese and English are available. Turn the Knob to select the
language. Then the pump displays the running interface.
Flow rates display
Dispensing display: Dispensing parameters are displayed in two
interfaces, Press Exit Key to switch these two interfaces.
a. Current flow rates: Display current flow rates. Turn the Knob to
increase or decrease the flow rates.
b. Current speed: Display current speed. The speed will change when
adjusting the flow rates.
c. Running direction: Indicate the direction of the pump. The running
direction of the pump can't be changed.
d. Running status: means the pump runs; means the pump
stops; means the pump is in prime state.
e. Control mode: INT means the pump is controlled internally; V means the
pump is controlled by external analog voltage signal; mA means the
pump is controlled by external analog current signal; Hz means the pump
is controlled by external 0 10 kHz pulse signal. Off means shutting off the
external control function by setting menu;
f. Dispensing volume: Display dispensing volume in dispensing mode.
g. Copy number: Display copy number under dispensing mode.
h. Dispensing time: Display the dispensing time. When the dispensing
procedure starts, the dispensing time will be counted down. Adjust the
flow rates or dispensing volume to change the dispensing time in
dispensing parameters setting interface.
【】 【】
【】
Micro Gear Pump Drive Operating Manual
3 4
Micro Gear Pump Drive Operating Manual
Menu Navigation Diagram

Knob
Function 1: Turn the to adjust the flow rates in flow rates display state.
Function 2: Turn the to select the menu and set the parameters, press
for confirmation in menus selection state.
Turn on or off the pump.
Knob
Knob
Knob
Power Switch
Running Interface
Turn on the pump, the pump is initialized first and select the language.
Chinese and English are available. Turn the Knob to select the
language. Then the pump displays the running interface.
Flow rates display
Dispensing display: Dispensing parameters are displayed in two
interfaces, Press Exit Key to switch these two interfaces.
a. Current flow rates: Display current flow rates. Turn the Knob to
increase or decrease the flow rates.
b. Current speed: Display current speed. The speed will change when
adjusting the flow rates.
c. Running direction: Indicate the direction of the pump. The running
direction of the pump can't be changed.
d. Running status: means the pump runs; means the pump
stops; means the pump is in prime state.
e. Control mode: INT means the pump is controlled internally; V means the
pump is controlled by external analog voltage signal; mA means the
pump is controlled by external analog current signal; Hz means the pump
is controlled by external 0 10 kHz pulse signal. Off means shutting off the
external control function by setting menu;
f. Dispensing volume: Display dispensing volume in dispensing mode.
g. Copy number: Display copy number under dispensing mode.
h. Dispensing time: Display the dispensing time. When the dispensing
procedure starts, the dispensing time will be counted down. Adjust the
flow rates or dispensing volume to change the dispensing time in
dispensing parameters setting interface.
【】 【】
【】
Micro Gear Pump Drive Operating Manual
3 4
Micro Gear Pump Drive Operating Manual
Menu Navigation Diagram

Pump Head Operation
Pump Head Installation:
The pump head is mounted on drive before the pump leaves the factory.
Follow below procedure for changing another pump head.
1.Loose the three M3 screws which connect the pump head and the pump
head bracket. Dismantle the pump head slightly.
2.Put the new pump head in the old pump head location. Pay attention to
the inlet and outlet locations of the pump head. Use three M3 screws to
connect the pump head and the pump head bracket.
Turn off the power supply before changing the pump head.
Pump Heads and Flow rates
85.7~857.1
171.4~1714.3
257.1~2571.4
MS(MG)204
MS(MG)209
MS(MG)213
Acceptable
Pump Heads
Flow Rates(mL/min)
0 00(rpm)30 30~
Part Number
05015010001
05015010002
05015010003
MG MS()Strong Magnet
05015010011
05015010012
05015010013
Pump Head Setting
Press the to highlight Pump Head line, press again to enter pump
head selection interface, turn to select the pump head, press the
for confirmation and return to previous menu, or press not to store
the selection and return to previous menu.
Knob Knob
Knob Knob
Exit Key
Flow Mode Operation
Enter Flow Mode
Press and turn the to highlight control mode line. Press to enter
next interface, turn to select control mode, press for confirmation.
Press not to store the selection and return to previous menu.
Knob Knob
Knob Knob
Exit Key
Flow Control: Turn the to adjust the flow rates.Knob
Flow Calibration
Press and turn to highlight calibration line. Press to enter next
interface. Turn to select . Press to highlight test time
line. Press again to highlight the value of time. Turn to select
test time (its range is from 30 to 1800 seconds), press for
confirmation. Press not to store the selection and return to
previous menu.
Press , the LCD displays running time and actual volume. Running
time counts down. Turn to input actual test volume. Press for
confirmation. The calibration operation can be repeated.
Knob Knob
Knob Flowrate Knob
Knob Knob
Knob
Exit Key
Run Key
Knob Knob
5 6
Micro Gear Pump Drive Operating ManualMicro Gear Pump Drive Operating Manual
If the actual volume is known in advance, enter the calibration interface and
input the actual volume directly.

Pump Head Operation
Pump Head Installation:
The pump head is mounted on drive before the pump leaves the factory.
Follow below procedure for changing another pump head.
1.Loose the three M3 screws which connect the pump head and the pump
head bracket. Dismantle the pump head slightly.
2.Put the new pump head in the old pump head location. Pay attention to
the inlet and outlet locations of the pump head. Use three M3 screws to
connect the pump head and the pump head bracket.
Turn off the power supply before changing the pump head.
Pump Heads and Flow rates
85.7~857.1
171.4~1714.3
257.1~2571.4
MS(MG)204
MS(MG)209
MS(MG)213
Acceptable
Pump Heads
Flow Rates(mL/min)
0 00(rpm)30 30~
Part Number
05015010001
05015010002
05015010003
MG MS()Strong Magnet
05015010011
05015010012
05015010013
Pump Head Setting
Press the to highlight Pump Head line, press again to enter pump
head selection interface, turn to select the pump head, press the
for confirmation and return to previous menu, or press not to store
the selection and return to previous menu.
Knob Knob
Knob Knob
Exit Key
Flow Mode Operation
Enter Flow Mode
Press and turn the to highlight control mode line. Press to enter
next interface, turn to select control mode, press for confirmation.
Press not to store the selection and return to previous menu.
Knob Knob
Knob Knob
Exit Key
Flow Control: Turn the to adjust the flow rates.Knob
Flow Calibration
Press and turn to highlight calibration line. Press to enter next
interface. Turn to select . Press to highlight test time
line. Press again to highlight the value of time. Turn to select
test time (its range is from 30 to 1800 seconds), press for
confirmation. Press not to store the selection and return to
previous menu.
Press , the LCD displays running time and actual volume. Running
time counts down. Turn to input actual test volume. Press for
confirmation. The calibration operation can be repeated.
Knob Knob
Knob Flowrate Knob
Knob Knob
Knob
Exit Key
Run Key
Knob Knob
5 6
Micro Gear Pump Drive Operating ManualMicro Gear Pump Drive Operating Manual
If the actual volume is known in advance, enter the calibration interface and
input the actual volume directly.

Enter Dispensing Mode
Press and turn the to highlight Control Mode line. Press to enter
next interface, turn to select , press for confirmation.
Press not to store the selection and return to previous menu.
Knob Knob
Knob Dispensing Knob
Exit Key
Dispensing Mode Operation
Dispensing Volume
The volume to be dispensed between two time intervals.
Press and turn to highlight dispensing setting line. Press to
highlight dispensing volume line. Press again to highlight the value
of the volume. Turn to select dispensing volume, press for
confirmation. Press not to store the selection and return to
previous menu.
Change the dispensing volume, the dispensing time will change
accordingly.
Knob Knob
Knob
Knob Knob
Exit Key
Flow Mode Operation Procedure Copy No.
the total filling number in dispensing mode. Its range is from 0 to 9999.
Press and turn to highlight copy number line. Press to enter
next interface. Turn to select copy number, press for
confirmation. Press not to store the selection and return to
previous menu.
If the copy no. is “0”, the dispensing process of the pump will continue
until press or shut off the pump to stop dispensing.
Knob Knob
Knob Knob
Exit Key
Stop key
Flow Rate Setting
the pump's flow rates in dispensing mode. Adjusting the dispensing
flow rates can change the dispensing time.
Press and turn to highlight dispensing flow rates line. Press
To enter next interface, turn to select suitable flow rates, press
forconfirmation.Press nottostoretheselectionandreturnto
previous menu.
Knob Knob
Knob Knob
Exit Key
Pause Time: Time Interval between every dispensing operation.
Press and turn to highlight pause time line. Press to enter
next interface. Turn to select pause time, press for
confirmation. Press not to store the selection and return to
previous menu.
Knob Knob
Knob Knob
Exit Key
7 8
Micro Gear Pump Drive Operating ManualMicro Gear Pump Drive Operating Manual