Baratza Vario+ User manual

Rev 1/5/2021 (v1.0)
EN
Vario+
®
QUICK START GUIDE
2
5
4
10
7
9
5
1
6
8
6
12
11
4
3
13
9
7
8
Thank you for choosing the
Baratza Vario+ for your home
grinding needs!
This is just a quick start guide. If you would like more detailed instructions,
please skip ahead to the full manual, found online at
baratza.com/documentation/
SETUP:
1. Remove everything from the packaging and hand wash the lid (1),
hopper (2) and grounds bin (13) with warm soapy water. Let air dry.
2. Position the shut-off knob (3) near the rear left of the grinder, apply
downward force, and feel for the hopper to insert into place. Once
inserted, rmly rotate the hopper clockwise to center the shut-off
knob and lock the hopper into place.
3. If using the grounds bin, remove the PortaHolder (10) by pulling
rmly out, then insert the grounds bin.
If using the PortaHolder and you nd it needs adjustment to t your
portalter: remove the PortaHolder, loosen screws on the back, adjust
the arms’ position, then tighten screws gently.
4. Plug in the grinder.
5. Reference the Grind Settings Chart below and set the grind size.
6. When adjusting ner, the grinder must be running or completely
empty of beans to prevent the adjustment system from binding on
beans that are between the burrs.
7. Add beans to the hopper.
8. Select grind time preset (9) or manual mode (8) then press start (7)
to grind.
9. Presets 1, 2 and 3 set the grinder to run for a designated time and
can be adjusted with the up/down arrows (4) and saved to a preset
by pressing and holding that preset button. Manual (M) mode runs
the grinder until the Stop button is pressed or 90 seconds max.
PARTS IDENTIFICATION
1. Hopper lid
2. Bean hopper
3. Bean shut-off knob
4. Grind time preset
adjustment buttons
5. Micro adjustment lever knob
6. Macro adjustment lever knob
7. Start/Stop button
8. Manual mode button
9. Grind time presets
10. PortaHolder
11. Burr calibration tool
(see manual)
12. Burr removal tool
(see manual)
13. Grounds bin

Rev 1/5/2021 (v1.0)
ENEN
®
QUICK START GUIDE
IF YOU NEED FURTHER SUPPORT:
In US & Canada contact
[email protected]
or 425-641-1245
or toll free 877-701-2021
If you think your grinder is not performing correctly, go to our
troubleshooting guides at baratza.com/troubleshooting
Outside North America, the warranty is provided by the company you
purchased from. For service, nd the nearest importer at
baratza.com/international-importers-and-retailers
GRIND SETTINGS CHART
The suggested settings below are starting points. You can adjust ner or coarser according to your taste or recipe preferences.
Espresso AeroPress Chemex Automatic Drippers Hario V60 French Press
2Q 4M 9M 7M 6M 10M
SAFETY INFORMATION:
Please read the information below very carefully. It contains important safety information for this appliance. Keep these instructions for future reference.
! Use only with AC current and the correct voltage. See the label on the
base of the grinder to determine the correct voltage.
! Only clean the grinder housing with a dry or slightly damp cloth. Do not
immerse the grinder, plug or cord in water or any other liquid.
! Baratza will not accept any liability for damage, injury, or warranty if the
grinder is used other than for its intended purpose (i.e. grinding roasted
whole coffee beans) or is improperly operated or repaired.
! Do not operate the grinder with a damaged cord or plug. If the supply
cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualied persons in order to avoid a hazard.
! Keep the appliance and its cord out of reach of children aged less than
8 years.
! Do not leave your grinder unattended while turned ON.
! This appliance can be used by children aged from 8 years and above
and persons with reduced physical, sensory or mental capabilities or
lack of experience and knowledge if they have been given supervision
or instruction concerning use of the appliance in a safe way and
understand the hazards involved.
! Cleaning and user maintenance shall not be made by children without
supervision.
! Always unplug the grinder from the electrical supply before assembling,
disassembling or cleaning. To unplug, grasp plug and remove from the
outlet. Never pull on the cord.
! CAUTION: ALWAYS unplug the electrical supply cord prior to cleaning
the grinder