Barco MDSC-1119 User manual

Getting Started Guide
MDSC-1119/MDSC-2124

(This page intentionally left blank.)
2
(This page intentionally left blank.)

3
Copyright notice
This document is copyrighted. All rights are reserved. Neither this
document, nor any part of it, may be reproduced or copied in any form
or by any means - graphical, electronic, or mechanical including
photocopying, taping or information storage and retrieval systems -
without written permission of Barco
© 2010 Barco N.V. All rights reserved.
Notice
Although every attempt has been made to achieve technical accuracy in
this document, we assume no responsibility for errors that may be
found. Our goal is to provide you with the most accurate and usable
documentation possible; if you discover errors, please let us know.
Barco software products are the property of Barco. They are distributed
under copyright by Barco N.V. or Barco, Inc., for use only under the
specific terms of a software license agreement between Barco N.V. or
Barco Inc. and the licensee. No other use, duplication, or disclosure of a
Barco software product, in any form, is authorized.
The specifications of Barco products are subject to change without
notice.
Trademarks
All trademarks and registered trademarks are property of their
respective owners.

Table of Contents
4
Table of Contents
Preface ................................................................................................. 5
FCC compliance information ........................................................ 5
Environmental information.......................................................... 6
Safety Instructions........................................................................ 9
Recommendations for using your display system ................... 13
Explanation of symbols.............................................................. 14
Introduction ....................................................................................... 16
Display parts, controls and connectors...................................... 17
Front..................................................................................... 17
Rear...................................................................................... 19
Connectors........................................................................... 19
Installation precautions ............................................................. 25
Vesa-mount installation............................................................. 25
Connecting the signal cables..................................................... 26
Cleaning instructions ......................................................................... 29
Precautions ................................................................................. 29
Front filter................................................................................... 29
Cabinet........................................................................................ 31
Technical information........................................................................ 32
Connector pin assignments ....................................................... 32
Power cable recommendations................................................. 36
Technical specifications.............................................................. 37

Preface
5
Preface
FCC compliance information
FCC Compliance Information (display)
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
Canadian notice
This ISM device complies with Canadian ICES-001.
Cet appareil ISM est conforme à la norme NMB-001 du Canada.

Preface
6
Environmental information
Disposal Information
This product consists of devices that may contain mercury, which must
be recycled or disposed of in accordance with local, state, or country
laws. (Within this system, the backlight lamps in the monitor display
contain mercury.)
This equipment has required the extraction and use of natural resources
for its production. It may contain hazardous substances for health and
environment.
In order to avoid the dissemination of those substances in the
environment and to diminish the pressure on natural resources, we
encourage you to use the appropriate take-back systems.
Those systems will reuse or recycle most of the materials of your end-
of-life equipment in a sound way.
The crossed-out wheeled bin symbol invites you to use those
systems.
If you need more information on the collection, reuse and
recycling systems, please contact your local or regional waste
administrator.
You can also contact us for more information on the environmental
performances of our products.

Preface
7
Information for China ROHS compliance
Table of toxic and hazardous substances/elements and their content, as
required by China’s management methods for controlling pollution by
electronic information products
中国大陆 RoHS
根据中国大陆《电子信息产品污染控制管理办法》(也称为中国大陆 RoHS)，
以下部份列出了本产品中可能包含的有毒有害物质或元素的名称和含量。
本表适用的产品
液晶显示器
有毒有害物质或元素
Toxic or hazardous Substances and Elements
Part Name Pb Hg Cd Cr6+ PBB PBDE
Metal parts O O O O O O
Plastic parts O O O O O O
PCB or PCBA O O O O O O
LCD panel X X O O O O
Power supply/adapter X O O O O O
Power cable X O O O O O
Connectors and cables O O O O O O
O: Indicates that this toxic or hazardous substance contained in all of the homogeneous
materials for this part is below the limit requirement in SJ/T11363-2006.
X: Indicates that this toxic or hazardous substance contained in at least one of the
homogeneous materials used for this part is above the limit requirement in SJ/T11363-2006

Preface
8
LCD Monitor
零部件名稱 有毒有害物質或元素
铅
（Pb）
汞
（Hg）
镉
（Cd）
六价铬
（Cr6+）
多溴联苯
（PBB）
多溴二苯醚
（PBDE）
金 ? 机构件 OOO O O O
塑料机构件 OOO O O O
电路板组件 *OOO O O O
液晶面板 XXO O O O
电源模块 / 适配器 XOO O O O
电源线 XOO O O O
外部信号连接线 OOO O O O
*：电路板组件包括印刷电路板及其构成的零部件，如电阻、电容、集成电路
、连接器等
○：表示该有毒有害物质在该部件所有均质材料中的含量均在 《电子信息产品中有
毒有害物质的限量要求标准》规定的限量要求以下
×：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 《电子信息产品
中有毒有害物质的限量要求标准》规定的限量要求；
但是上表中打 “×”的部件，其含量超出是因为目前业界还没有成熟的可替代的技术

Preface
9
Safety Instructions
General Recommendations
Read these safety and operating instructions before operating the
display.
Retain safety and operating instructions for future reference.
Adhere to all warnings on the display and in the manuals.
Follow all instructions for operation and use.
Electrical shock
Type of protection (electrical):
Class I equipment
Degree of safety (flammable anesthetic mixture):
Equipment not suitable for use in the presence of a flammable
anesthetic mixture with air or with oxygen or nitrous oxide.
Non-patient care equipment
Equipment primarily for use in a health care facility that is intended for
use where contact with a patient is unlikely.
The display may not be used with life support equipment.
Mission critical applications
We strongly recommend there is a replacement display immediately
available in mission critical applications.

Preface
10
Power connection
• Power requirements: The display must be powered using the
supplied medical approved 24 VDC power supply.
• The medical approved DC power supply must be powered by the
AC mains voltage.
• The display complies to the mentioned standards only when
used with the supplied medical power supply.
• The display must be powered from a center-tapped electrical
circuit when used in the USA at voltages above 120 Volts.
• The display is intended for continuous operation.
• The display is powered from an external power supply for class I
equipment. The installer is responsible for testing the display’s
earth ground to verify that it meets the impedance
requirements for the given country regulatory requirements.
• The display must be earthed by a minimum 18 AWG, maximum
6 foot (1.8m) long wire connected to the ground connection at
the rear.
Power cords:
• Utilize a UL-listed detachable power cord, 3-wire, type SJ or
equivalent, 18 AWG min., rated 300 V min., provided with a
hospital-grade type plug 5-15P configuration for 120V
application, or 6-15P for 240V application.
• Do not overload wall outlets and extension cords as this may
result in fire or electric shock.
• Mains lead protection (U.S.: Power cord): Power cords should be
routed so that they are not likely to be walked upon or pinched
by items placed upon or against them, paying particular
attention to cords at plugs and receptacles.

Preface
11
Water and moisture
The display is IPx1 compliant.
Note: The power supply is not approved for IPx2. The power
supply must be mounted in a flat position for best resistance to
fluids.
Ventilation
Heed the necessary free space around the display to allow enough air
flow for cooling of the display.
Installation
Place the display on a flat, solid and stable surface that can support the
weight of at least 3 displays. If you use an unstable cart or stand, the
display may fall, causing serious injury to a child or adult, and serious
damage to the equipment.
Do not allow to climb or rest on the display.
When adjusting the angle of the display, move it slowly so as to prevent
the display from moving or slipping off from its stand.
When display is attached to an arm, do not use the display as a handle
or grip in order to move the display. Please refer to the instruction
manual of the arm for instructions on how to move the arm with the
display.
Provide full attention to safety during installation, periodic maintenance
and examination of this product.
Sufficient expertise is required for installing this product, especially to
determine the strength of the wall for withstanding the display’s
weight. Be sure to entrust the attachment of this product to the wall to
licensed contractors of Barco and pay adequate attention to safety
during the installation and usage.
Barco is not liable for any damage or injury caused by mishandling or
improper installation.
More warnings in the Installation chapter.

Preface
12
This apparatus conforms to:
CE0120 (MDD 93/42/EEC class I product), IEC 60601-1, UL 60601-1,
CAN/CSA C22.2 No. 601.01-M90 (c-UL),
CCC GB4943-1995 (IEC 60950-1) (MDSC-1119 only).
National Scandinavian Deviations for Cl. 1.7.2 :
Finland: "Laite on liitettävä suojamaadoituskoskettimilla varustettuun
pistorasiaan"
Norway: "Apparatet må tilkoples jordet stikkontakt"
Sweden: "Apparaten skall anslutas till jordat uttag"

Preface
13
Recommendations for using your display system
Operating precautions: How to avoid image retention
Continuous operation of the display with the same image or static
image elements may result in some image sticking on the LCD panel.
This is especially a risk in applications where the display is connected to
a computer.
In mission critical applications, do not activate a screen saver or power
save mode. In other applications, especially when the display is
connected to a computer, take the following precautions:
1. Switch on DPMS or Power Save on display and PC:
• The display Power Save setting can be switched on in the
display’s Settings menu (see Online user manual).
• The PC DPMS setting can be switched on in the Windows XP
Display control panel (Screen Saver tab > Monitor power. In the
‘Turn off monitor’ drop-down box, select After 20 mins.).
2. Activate a good screen saver
• The screen saver can be selected in the Windows XP Display
control panel (Screen Saver tab). Select a screen saver without
static elements and select a Wait Time of 10 minutes.
3. In case you are working with the same image or an application
with static image elements for several hours continuously, change
the image content regularly to avoid image sticking of the static
elements.

Preface
14
Explanation of symbols
Symbols on the display and / or power supply
On the display or power supply, you may find the following symbols
(nonrestrictive list):
Indicates compliance to the essential require-
ments of the Directive 93/42/EEC
Indicates compliance with Part 15 of the FCC
rules (Class A or Class B)
or
Indicates the display is approved according to
the UL regulations
or
Indicates the display is approved according to
the c-UL regulations
Indicates the display is approved according to
the DEMKO regulations
Indicates the display is approved according to
the CCC regulations
Indicates the USB connectors on the display
Indicates the manufacturing date
Indicates the temperature limitations for the
display to operate within specs

Preface
15
Symbols used throughout the manual:
Indicates the display serial no.
Consult the operating instructions
Indicates this apparatus must not be thrown
in the trash but must be recycled, according
to the European WEEE (Waste Electrical and
Electronic Equipment) directive
Warning: Risk of
injury to human
beings
Caution: Risk of
damage to the
product
Important notice or
remark
Note
Hint, tip Additional
information

Introduction
16
Introduction
Thank you for choosing Barco.
Barco’s MDSC-1119/MDSC-2124 is a versatile multi-modality display for
endoscopic cameras, room and boom cameras, ultrasound, cardiology,
PACS, anesthesiology and patient information. This gives surgeons the
flexibility and information they need to perform surgeries with
maximum efficiency.
Flexibility and expandability
The MDSC-1119/MDSC-2124’s video bus architecture and modular slot
concept allow the display to be configured to specific OR video
connectivity requirements. Furthermore, Barco’s surgical display readily
supports new and future video formats, such as high-definition digital
video.
Picture-in-Picture
Dual channel Picture-in-Picture or Picture-by-Picture views of images
from multiple input signals give surgeons the required views, allowing
them to make more informed decisions.
Customized profiles
Surgeons can configure, store and recall user preferences and profiles
for each surgical procedure. This facilitates a streamlined, more
comfortable way of working and allows to instantly deliver and restore
optimally defined display settings at all times.
Note: Characters will look crisper and sharper than on a CRT
display. This is inherent to the used flat panel technology. For the
same reason, video images may appear somewhat blocked.
If you are not familiar with these image differences, you should
familiarize yourself before using the display in a critical application
and determine its usability.

Introduction
17
Display parts, controls and connectors
Front
The front controls are soft touch keys.
When you touch any of them while no on-screen display (OSD) is on the
screen, the front illumination is switched on for a few seconds.
When you touch a key again while the illumination is on, the function of
the key is executed.
Figure 1: Front view
1. Left navigation key
To move up in menus and decrease values in the OSD.
When Quick Input Selection is enabled (see below), this key
selects the previous input.
2. Right navigation key
To move down in menus and increase values in the OSD.
1 2 3 4
5

Introduction
18
When Quick Input Selection is enabled (see below), this key
selects the next input.
3. Enter
To display the OSD (on-screen display). In the OSD, this button acts
as Enter button to make selections.
4. Standby
To put the display in standby mode.
To switch the display in stand-by, touch and hold this key until the
display switches off. To turn the display on, touch and hold this key
for about 2 seconds until the display switches on.
5. Power LED
Indicates the display’s power status.
Green: Display is on (when enabled in the OSD).
Orange: Display is in Standby power-saving mode.
Off: Display is disconnected from the power or the LED’s on state is
disabled in the OSD.
Quick input selection
You can quickly select another video input as follows:
1. Make sure the OSD is not on the screen. If it is, exit the OSD.
2. Touch the navigation keys or . The illumination is switched on
and the current video input is displayed.
3. While the illumination is on, touch the navigation keys or to
select another video input.
The quick input selection feature can be enabled/disabled in the Setup
OSD menu.

Introduction
19
Rear
Figure 2: Rear view
1. Connector compartment cover.
Remove to get access to the signal connectors.
2. Compartment cover levers to lock/unlock the cover.
3. VESA mount screw holes.
Connectors
The connector configuration may depend on the customer’s
requirements. Below is a description of the default connector
configurations.
1
2
3

Introduction
20
Standard connectors MDSC 1119
Figure 3: Connectors
1. General purpose input/output (GPIO) connector. Switches (max.2)
connected to this plug can have different functions: Switch inputs
or display a short text on the screen. This function can be selected
in the on-screen menus.
2. +24VDC power input.
Connect the output of the DC power supply delivered with the
display to this connector.
3. RS-232 connector.
4. S-VHS video input.
5. SDI connector.
6. Input B / CVBS3 / Pb / C.
7. Input G / CVBS2 / Y / Y .
8. Input R / CVBS1 / Pr.
9. VGA input.
10. DVI-I input.
11. Slot for security cable (e.g., Kensington lock).
1 2 3 4 5 6 7 8 9 10 11