Winners Only GK Quick start guide

Notes: Need two people to assemble.
1
2
1
1
Instructions:
Chart 1
Step 1. Align back panel (E) to R1B pedestal (A), use (1-1/4") machine bolts (3PCS) to
connect them. Align corner leg-1 (H) to back panel (E), use (1-1/4") machine bolts (3PCS)
to connect them.
Chart 2
Step 2. Align RSF side panel (F) to corner leg-1 (H) , use (1-1/4") machine bolts (3PCS) to
connect them.
Step 3. Use (1-1/4") machine bolts (2PCS) to connect RHS glide panel (D) to back panel (E).
Step 4. Using a Mallet, carefully insert center Cross Bar (G) to R1B pedestal (A) and RHS
glide panel (D), carefully turn the assembled base straight up. Use (1-1/4") flat head
wood screws (2PCS) to connect Cross Bar (G) to R1B pedestal (A) and RHS glide
panel (D).
2
2
1
1
1
Turn the R1B pedestal (A) upside down.
X1
4X1
4
4

Chart 3
Step 5. Align back panel (O) to R2B pedestal (L), use (1-1/4") machine bolts (3PCS) to
connect them. Align corner leg-2 (J) to back panel (O) , use (1-1/4") machine bolts
(3PCS) to connect them.
Step 6. Align LHS glide panel (I) to back panel (O), use (1-1/4") machine bolts (2PCS) to
connect them.
Step 7. Using a Mallet , carefully insert cross bar (N) to R2B pedestal (L) and LHS glide
panel (I), carefully turn the assembled base straight up. Use (1-1/4") flat head wood
screws (2PCS) to connect cross bar (N) to R2B pedestal (L) and LHS glide panel (I).
Chart 4
Step 8. Assemble the Return Desk to the Main Desk by using (1-1/4") machine bolts (5PCS)
to connect RSF side panel (F) to corner leg-2 (J) and LHS glide panel (I) to
RHS glide panel (D).
Turn the R2B pedestal (L) upside down.
X6
5
5
5
5
5
5
X1
7
X1
7
X2
8
8
8
7

Chart 5
Step 9. Using a Mallet, carefully insert the wood dowels (6PCS) in R1B pedestal (A), RSF
side panel (F) and R2B pedestal (L).
Step 10. Loosen the screws to adjust metal figure 8 (23PCS) of its direction of the panel and
re-screw .
Chart 6 Once the R1 desk top (B) and R2 desk top (K) are aligned.
Step 11. Insert short (3/4") flat head wood screws (23PCS) through metal figure 8 to
connect R1 desk top (B),R2 desk top (K) and base.
Step 12. Use long (1-1/4") flat head wood screws (2PCS) to connect cross bar (G) to
R1 desk top (B), and cross bar (N) to R2 desk top (K).
11
9
10
11
X1
N
X10
12
K
11
9
910
10
10
10
10
10
10
10
10
10
10
10 10
10
10 10 10
10
10
10 10
10
99
X1
12
11
X13
11
11 11 11
11 1111
11 11
11 11 11
11 11 11 11 11
11
11
11
11
99

ball bearing
retainer
14
MAIN DESK
RETURN DESK
13
Chart 7
Step 13. Insert the Grommet on top of the Main Desk.
Step 14. Install the drop front center drawer (C) and keyboard pullout (M) to place .
Important:
(Be sure to move the ball bearing retainer all the way to the front of the glide
and carefully slide the rails into the glides and ball bearing retainer.)
Assembly is now complete
CM