Whittier Wood 2000AEGACa User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
06/14
Congratulations!
This fine piece of furniture will make a gorgeous addition to
your home. For the best results, read the Assembly
Instructions before you begin your project.
•Before you begin your project, completely read the Assembly Instructions.
•Store this item: 1- in its box; 2- in a dry place; 3- in temperatures that
range from 40°F to 90°F (not on a cold and possibly damp cement floor.)
•Periodically inspect your furniture for any loose glue joints, screws or
any other problem that might affect the stability of your furniture.
Tighten or repair as needed.
WARNING
Notice to California Customers
California Prop 65 requires consumer goods to be labeled if any one of
850+ different chemicals or substances, including wood dust, is present
even in trace amounts. Drilling, sawing, sanding or machining wood
products generates wood dust, a substance known to the State of
California to cause cancer. Warning: This product contains a chemical
or substance known to the State of California to cause cancer, birth
defects or other reproductive harm. California Health and Safety Code
Section 25249.6
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CALL US FIRST! Do not return this item to the store
Service Policy: We will replace any part that is defective,
missing or damaged during assembly. For a replacement
part, directly contact Whittier Wood Products customer
service department by phone, fax, mail or email.
Hours: Our friendly customer service staff can be reached
Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific Time). You
may leave a message 24 hours a day, seven days a week.
To Order: Provide the finish and furniture model number
(upper portion of this page), the part letter, production
code, quantity needed, reason for replacement and your
full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one or
two business days from the time we receive your request.
Please allow five to ten business days for delivery.
800-653-3336 • Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
IMPORTANT NOTES:
• For normal household use only. Not recommended for commercial use.
• Do not climb, sit or stand on this piece of furniture.
Assembly Instructions
AEGAC = Glazed Antique Cherry finish; AEGSP = Glazed Spice finish;
AECAF = Caffè finish
McKenzie Alder Bookcase Door Kits
2000AEGACa;
2000AEGSPa;
2000AECAFa
2003AEGACa;
2003AEGSPa;
2003AECAFa
2001AEGACa;
2001AEGSPa;
2001AECAFa
24" Alder Bookcase
2-Door Kit
36" Alder
Bookcase
2-Door Kit
30" Alder
Bookcase
2-Door Kit

Page 2 — 2000AEGACa_AEGSPa_AECAFa, 2001AEGACa_AEGSPa_AECAFa, 2003AEGACa_AEGSPa_AECAFa — 06/14
Before you begin to assemble this unit, identify each part and make sure the quantities received match what is on this list.
Part Description Quantity
A Door 2
BDoor Knob 2
Ca #8 x 1-1/2" Machine Screw Tuscan 2
D Hinge 4
E Hinge Plate 4
F Pad 2
If you need to replace a part, please refer to the following list for the part name and letter code.
2000AEGACa; 2000AEGSPa; 2000AECAFa
2001AEGACa; 2001AEGSPa; 2001AECAFa
2003AEGACa; 2003AEGSPa; 2003AECAFa
Alder Bookcase Door Kit — Parts List

Tool Required: Phillips Screwdriver
1. Lay the Doors (A) face down on a clean protected surface. Snap the handle of the Hinge (D)
down on to each of the Hinge Plates (E) as seen in Figures 1 and 1a.
2.
Page 3 — 2000AEGACa_AEGSPa_AECAFa, 2001AEGACa_AEGSPa_AECAFa, 2003AEGACa_AEGSPa_AECAFa — 06/14
ED
Fig. 1
Fig. 2 Fig. 2a
A
There are predrilled holes in the door as shown in Figure 1a. This is where you will be inserting the
hinge part of the assembly. Insert the Hinge (D) assembly that has the plastic knobs into the predrilled
holes in the bottoms and tops of the Doors (A).See Figures 2 and 2a. You must place both Hinges
into the Door before you attach them to the bookcase.
E
D
Fig. 1a
2000AEGACa; 2000AEGSPa; 2000AECAFa
2001AEGACa; 2001AEGSPa; 2001AECAFa
2003AEGACa; 2003AEGSPa; 2003AECAFa
Alder Bookcase Door Kit
Assembly Instructions

4.
Side adjustment
Depth adjustment
To move the door towards the side panel, rotate screw ‘2’ counter-clockwise. To move it away,
rotate screw ‘2’ clockwise.
Loosen screw ‘1’ and adjust door. Re-tighten screw.
Height adjustment Loosen screws ‘3’ and adjust door. Re-tighten screws.
Fig. 4
1
2
3
3
The door might need to be adjusted so that all the spaces between the doors and unit sides are
equal. To make those adjustments, follow the instructions in Figure 4.
Fig. 3 Fig. 3a
3. Attach the door to the bookcase by inserting the screws in the Hinge Plate (E) into the second
and third holes up from the bottom of the bookcase unit. See Fig. 3. Attach the second hinge
assembly to the same door/bookcase by inserting screws into the third and fourth predrilled holes
down from the top of the fixed center shelf. See Figure 3a.
Bottom
Center
shelf
Page 4 — 2000AEGACa_AEGSPa_AECAFa, 2001AEGACa_AEGSPa_AECAFa, 2003AEGACa_AEGSPa_AECAFa — 06/14

5. Attach the Knobs (B) to the Doors (A) with #8x1-1/2 " Machine Screws Tuscan (Ca). See Figure 3.
DOOR
Ca
B
6. Attach a Pad (F) to the back of each door where it comes in contact with the adjustable shelf.
Fx 2
B x 2
Fig. 4
Page 5 — 2000AEGACa_AEGSPa_AECAFa, 2001AEGACa_AEGSPa_AECAFa, 2003AEGACa_AEGSPa_AECAFa — 06/14
Ca x 2