BDI TANAMI BAR 7120 User manual

TANAMI™BAR 7120
BAR CABINET
DESIGN MATTHEW WEATHERLY
LET’S GET STARTED.
INSTRUCTION MANUAL

BDIUSA.COM | 3NEED ASSISTANCE? customerservic[email protected]
Congratulations on the purchase of your Tanami Bar 7120 from BDI. Your bar cabinet
has been designed to provide a lifetime of enjoyment. This manual will provide you with
assembly instructions and other helpful information that will ensure that you get the
most out of your cabinet. Please save it for future reference.
Your Tanami Bar has been engineered for simple assembly. It is designed for indoor use
on level floors. Clean wood, metal, and porcelain surfaces with a damp cloth. Please
follow these directions carefully to prevent any damage.
Should you need further assistance, contact BDI at customerservic[email protected].
ENJOY!

4 | BDIUSA.COM TANAMI 7120
HARDWARE AND COMPONENTSHARDWARE AND COMPONENTS
Unpack and identify the parts listed below. The assembly workspace should be a non-marring
surface such as carpet. For missing hardware pieces, please contact BDI Customer Service at
[e-mail].
Do not use power tools for assembly of this product.
For all other concerns, please contact your BDI retailer.
PART # H2
DESCRIPTION M6 x 12mm Screw
QUANTITY 8
PART # H4
DESCRIPTION Adhesive Bumper
QUANTITY 6
PART # H3
DESCRIPTION M6 x 76mm Screw
QUANTITY 2
PART # TI
DESCRIPTION Hex Wrench
QUANTITY 1
PART # T2
DESCRIPTION Leveler Wrench
QUANTITY 1
PART # H1
DESCRIPTION M6 x 12mm Flathead
Screw
QUANTITY 4

HARDWARE AND COMPONENTS
BDIUSA.COM | 5NEED ASSISTANCE? customerservic[email protected]
PART # C1
DESCRIPTION Cabinet
QUANTITY 1
PART # C3
DESCRIPTION Crossbar
QUANTITY 1
PART # C5
DESCRIPTION Adjustable Shelf
QUANTITY 1
PART # C2
DESCRIPTION Leg
QUANTITY 2
PART # C4
DESCRIPTION Glass Top
QUANTITY 1
PART # C6
DESCRIPTION Drawer Liner
QUANTITY 1

6 | BDIUSA.COM TANAMI 7120
STEP 1. BUILD THE BASEASSEMBLY
Find the 2 (C2) Legs inside the (C1) Cabinet.
Position 2 (C2) Legs towards the ends of
(C3) Crossbar as shown making sure the
countersunk holes on the (C2) Legs are facing
outward. Use 4 (H1) Flathead Screws and
(T1) Hex Wrench to assemble the base. Do not
fully tighten the screws yet.
PART/DESCRIPTION QTY
T1-HEX WRENCH 1
H1-FLATHEAD SCREW 4
H1
H1
C2
C2
C3

BDIUSA.COM | 7NEED ASSISTANCE? customerservic[email protected]
With help from another person, carefully position
(C1) Cabinet on its back (on top of a few layers
of packing material). Attach the base to the
bottom of (C1) Cabinet as shown using
8 (H2) Screws going through the metal tabs
and 2 (H3) Screws going through the (C3)
Crossbar. With all screws started, tighten all
screws with (T1) Hex Wrench.
PART/DESCRIPTION QTY
T1-HEX WRENCH 1
H2-SCREW 8
H3-SCREW 2
ASSEMBLY
STEP 2. ATTACH THE BASE
C1
H3
H2
H2
H2
H3
2 PERSON TASK
H2
H3
H2
C3
H2
C3
Metal Tabs

8 | BDIUSA.COM TANAMI 7120
STEP 3. ATTACH BUMPERS
STEP 4. PLACE GLASS TOP
ASSEMBLY
ASSEMBLY
First,remove white paper backing and attach
6(H4) Adhesive Bumpers to the bottom of the
(C4) Glass Top positioned approximately 1 cm
(3/8”) away from the edges.
NOTE: Bottom of the glass is painted white.
Second,remove the clear film from the
exposed side of the bumpers to allow the
bumpers to grip the top of the (C1) Cabinet.
With help from another person lift and rotate
the cabinet onto its base, being careful to
prevent it from sliding on the floor. With
painted surface and bumpers facing down,
place the (C4) Glass Top on top of
(C1) Cabinet and align the edges with the
edges of the cabinet.
PART/DESCRIPTION QTY
H4-BUMPER 6
1. Remove paper
from adhesive side
2. Remove clear
film from grip side
C4
H4
H4
H4
H4
H4
H4
C1
C4
2 PERSON TASK

BDIUSA.COM | 9NEED ASSISTANCE? customerservic[email protected]
Install the (C5) Adjustable Drawer in the lower right quadrant. Open the drawer and install the
(C6) Drawer Liner. The shelf height in the lower right quadrant may be adjusted up or down.
If desired, unscrew the 4 shelf pins and reposition at the desired level.
ASSEMBLY
STEP 5. INSTALL ADJUSTABLE SHELF AND DRAWER LINER
C5
C6
Shelf pins

10 | BDIUSA.COM TANAMI 7120
LEVEL CABINET BAR
FINE TUNING
Once the unit is completely assembled and in
its final position, adjust the levelers using
(T2) Leveler Wrench. To hold the doors in an
open position, partially dial out the two front
levelers. This action will tilt the cabinet back
slightly, preventing the open doors from swinging
towards their closed position.
Next, leveling the cabinet from side-to-side will help align the 2 front doors.
Level side-to-side
Dial down
PART/DESCRIPTION QTY
T2-LEVELER WRENCH 1
T2

BDIUSA.COM | 11NEED ASSISTANCE? customerservic[email protected]
With both doors closed, check to see if the top
corners of the doors align. If not, dial out the
corresponding front leveler under the door that
is sagging.
Example: If the door on the right is low, dial out the
right front leveler to raise the door back into alignment with the left door
ASSEMBLY
STEP 4. INSTALL BACK PANELS FINE TUNING ADJUST DOOR GAPS—IF NEEDED
To move the right door up, dial
the front, right leveler out.
To move the left door up, dial the
left, front leveler out.
PART/DESCRIPTION QTY
T2-LEVELER WRENCH 1
Dial down
T2

12 | BDIUSA.COM TANAMI 7120
Finally, if when closed, the gap between the
doors is more narrow at the top verses the
bottom, this can be remedied by adjusting the
door height adjustment screws located on the
bottom front edge of the base.
To adjust the door height adjustment screws, insert the (T1) Hex Wrench into the holes just under the
adjustment screws and adjust either up or down as needed. Adjust 1 or both of the screws as needed.
For realtime feedback, close both doors and watch the door gap as you turn the adjustment screws.
ADJUST DOOR GAPS—IF NEEDED (CONTINUED)
FINE TUNING
PART/DESCRIPTION QTY
T1-HEX WRENCH 1
Both doors sagging evenly—
Dial up both door height
adjustment screws

BDIUSA.COM | 13NEED ASSISTANCE? customerservic[email protected]
FINE TUNING
Door height
adjustment
screws
Dial up
T1
ADJUST DOOR GAPS—IF NEEDED (CONTINUED)

14 | BDIUSA.COM TANAMI 7120
CARE & MAINTENANCE
GLASS
Glass surface is maintained using household glass cleaner and a paper towel or cloth.
SATIN-ETCHED GLASS
This uniquely smooth-to-the-touch glass surface can be regularly maintained using household glass
cleaner and a paper towel or cloth. Minor scratches or scuffs not eliminated using paper towel or cloth
can usually be removed by using a ‘Magic Eraser’. Magic Eraser is a melamine foam product available
at any grocery store or home improvement center. Dampen the entire glass surface as well as the
Magic Eraser, then rub the entire glass surface in broad, even strokes using moderate pressure. Clean
and dry the surface with a paper towel. Check for results and repeat as necessary.
Any scratches or scuffing not eliminated by one of the above methods can often be addressed by
‘refreshing’ the glass. This is a process that should not be required more than once per 6-12 months.
See this brief video for the simple method: www.bdiusa.com/glass
WOOD
Wood surfaces should be cleaned with a slightly damp (not saturated) cloth or paper towel. Do not
use glass cleaner on wood. If moisture remains, dry the surface with another cloth. If needed, a gentle
non-abrasive cleanser may be used, but be sure to wipe away all cleaner residue and dry the surface
with a cloth.
BDI’s wood finishes feature natural hardwood solids and veneers. Wood is a product of nature and—
unlike man-made materials that can be manufactured to strict and consistent specifications—has
natural imperfections that are part of its appeal and character. Every piece of wood differs from every
other, even when coming from the very same tree. As such, variation in grain, texture and tone should
be expected from one panel or piece of furniture to the next.
While BDI’s stained wood finishes are stable in tone & appearance, all finishes are subject to some
degree of discoloration with prolonged exposure to direct sunlight. Please take care to avoid
positioning your BDI cabinet in any area with extensive direct sunlight. To learn more about the
features of natural wood, visit www.bdiusa.com/wood
METAL & PAINTED SURFACES
Surfaces should be cleaned with a slightly damp (not saturated) cloth or paper towel. If moisture
remains, dry the surface with another cloth. If needed, a gentle non-abrasive cleanser may be used,
but be sure to wipe away all cleaner residue and dry the surface with a cloth.

BDIUSA.COM | 15NEED ASSISTANCE? customerservic[email protected]
WARRANTY
PRODUCT REGISTRATION
WARNING
BDI warrants to the original purchaser that for the below stated warranty term, BDI will repair or
replace any product, part, or component covered by this warranty which fails under normal use as a
result of a defect in material or workmanship. BDI will repair or replace the aforementioned product,
part or component with a comparable product, part or component. The decision to repair or replace
will be at BDI’s sole discretion.
BDI Home Theater Furniture, Office Furniture, Modular Systems, Tables and other furniture pieces are
warranted for three (3) years from the date of purchase as shown on your sales receipt. The
warranty period starts from the date of purchase. This warranty extends only to the original
purchasers who acquire new product from BDI Authorized Resellers. Any product, part, or
component must have been assembled, installed, used, and maintained according to BDI’s published
instructions in order to be eligible for warranty coverage. Any modification to the original product
voids the warranty.
To view BDI’s complete warranty information, visit www.bdiusa.com/warranty
Registering your new BDI product allows us to send you important product updates, service
information and helpful hints related to your BDI products. Register today, and you will be entered
to win free a BINK table from BDI: www.bdiusa.com/register
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM FURNITURE TIP-OVER. TO HELP
PREVENT TIP-OVER:
nInstall tip-over restraint.
nPlace heaviest items in lower compartments.
nNever allow children to climb or hang on drawers, doors or shelves.
nNever open more than one drawer at a time.
USE OF TIP-OVER RESTRAINT MAY REDUCE—BUT NOT ELIMINATE—THE RISK OF TIP-OVER.

These distinctive product configurations are protected by US and international patents, trade
dress, and/or copyright laws. Tanami & BDI are trademarks of Becker Designed, Inc. All rights
reserved. ©2020, BDI | V.03.17.2020
Made in China.