Barracuda NG Firewall F180 User manual

Barracuda CloudGen Firewall
Barracuda NG Firewall F180 Revision A 1 / 5
Barracuda NG Firewall F180 Revision A
https://campus.barracuda.com/doc/46203411/
Opening your Barracuda Networks appliance or removing its warranty label unless instructed to
do so by Barracuda Networks support will void your warranty and hardware support.
Barracuda Networks Appliance Safety Instructions
Always use the power supply shipped with the appliance.
General
Revision A
Front
Back
Default Port Configuration
Label OS Notation Speed/Type Management Port
1 p1 10/100/1000 MBit RJ45 X
2 p2 10/100/1000 MBit RJ45
3 p3 10/100/1000 MBit RJ45
4 p4 10/100/1000 MBit RJ45
5 p5 10/100/1000 MBit RJ45
6 p6 10/100/1000 MBit RJ45
s1-s8 p7 10/100/1000 MBit RJ45 switch
Hardware Specifications

Barracuda CloudGen Firewall
Barracuda NG Firewall F180 Revision A 2 / 5
Component Specifications
CPU Intel Atom Dual Core
Memory 2 GB
Mass Storage 1 x 80 GB SSD
Flash Disk -
USB 4x USB 2.0
Form Factor Desktop
Dimensions (W/D/H) 14.88 x 6.38 x 1.73 in
378 x 162 x 44 mm
Net Weight 2.08 kg
Power Supply Input Voltage 100 - 240 V, AC
Power Supply Output Voltage 19 V, DC
Power Supply Voltage 50 Hz – 60 Hz
Power Supply Watts 45 W
Storage Temperature -20 °C - +70 °C
Operation Temperature 0 °C to +35 °C
Relative Humidity 5% - 95%, non-condensing
Fan 1 System Fan
Certifications CE, FCC, ROHS
Wi-Fi 802.11 b/g or better extended range Wi-Fi adapter
The hardware specifications list was valid at the time this manual was published. The listed
components are subject to change at any time, as Barracuda Networks may change hardware
components due to technological advancements. Therefore, the list may not reflect the current
hardware configuration of the Barracuda Networks NG Firewall or NG Control Center appliance it
was delivered with.
Wall Mount Kit
This appliances is shipped with a wall mount kit. Print the Barracuda NG Firewall Wall Mount Jig to use
as a template when drilling the required holes. Do not scale the PDF when printing.
Status LED
Your appliance is equipped with a variety of LEDs. One of them is the Status LED. It is labeled

Barracuda CloudGen Firewall
Barracuda NG Firewall F180 Revision A 3 / 5
either with a heart symbol or the term Status. It indicates the appliance’s operational state by
changing colors between green, orange, and red and by changing between blinking and steady
glowing. The table below shows the different meanings of the different glowing states.
Your appliance is equipped with a variety of LEDs and acoustic signals. The front panel of
the Barracuda NG Firewall F80 contains one power LED (blue), one disc LED (green), one status LED
(red), and 4 port LEDs. On the back panel, you can see one power button LED and various port LEDs.
Two acoustic signals indicate status of installation.
LED Color Glowing State Meaning
All LED Off Off Appliance is powered off, or installation has not initialized far
enough for LED control when installation is started.
Power LED -
BLUE steady Appliance is plugged in and is on.
Status LED - RED Off Power LED on and Status LED off: Box is running normally, or
Installation has finished successfully.
Steady
Appliance is halted and may be disconnected, or an error
occurred preventing the Barracuda NG Firewall from entering the
up state.
Blinking slowly
(1/s interval)
Normal installation, or appliance is either booting, shutting down,
or performing a system update.
Blinking fast
(4/s interval) Error during installation, or appliance is in ART mode.
Disc LED -
GREEN Blinking Appliance is accessing the internal storage.
Port LEDs (front)
- GREEN Blinking Port in use (Data transfer).
Port LEDs (back)
- GREEN Left blinking Port in use (Data transfer) – Yellow (10/100 Mbps).
Right steady Port is on.
Acoustic Signal Frequency Meaning
Beep 1 time
(.) Appliance is booting.
Beep 3 times
(...)
Installation was completed successfully; appliance is halted for
reboot. After reboot, one beep will again indicate booting.
Beep 3 times long
(_ _ _) Error during installation
LED and acoustic signals may vary between different appliance models.

Barracuda CloudGen Firewall
Barracuda NG Firewall F180 Revision A 4 / 5
Serial Console Port
In order to establish a console connection to the appliance using an RJ45 serial cable, you need to
configure the serial port on the terminal using the following parameters:
Parameter Value
Baud 19200
Bits 8
Stop bit 1
Parity None
Handshake None

Barracuda CloudGen Firewall
Barracuda NG Firewall F180 Revision A 5 / 5
Figures
F180_front.png1.
F180_back.png2.
© Barracuda Networks Inc., 2022 The information contained within this document is confidential and proprietary to Barracuda Networks Inc. No
portion of this document may be copied, distributed, publicized or used for other than internal documentary purposes without the written consent of
an official representative of Barracuda Networks Inc. All specifications are subject to change without notice. Barracuda Networks Inc. assumes no
responsibility for any inaccuracies in this document. Barracuda Networks Inc. reserves the right to change, modify, transfer, or otherwise revise this
publication without notice.