Barracuda CloudGen Firewall F1000 CE0 User manual

Barracuda CloudGen Firewall
F1000 Revision A 1 / 8
F1000 Revision A
https://campus.barracuda.com/doc/71862294/
The Barracuda CloudGen Firewall F1000 is available in four different sub-models. Each model offering
a different setup of port modules. The Barracuda CloudGen Firewall F1000 has four different NIC
module bays that can be equipped with the following field replaceable Barracuda Network Modules:
M1001
M1002
M1003
M1004
F1000 Rev. A Model CE0 (16x1 GbE RJ45 and 4x10GbE SFP+ Optical Fiber)
F1000 Rev. A Model CE2 (32x1GbE RJ45 Ethernet and 8x10GbE SFP+ Optical Fiber)
F1000 Rev. A Model CFE (16x1GbE RJ45 Ethernet, 16x1GbE SFP Optical Fiber, and 8x10GbE SFP+ Optical Fiber)
F1000 Rev. A Model CFEQ (16x1GbE RJ45 Ethernet, 16x1GbE SFP Optical Fiber, and 6x10GbE SFP+ Optical Fiber, 2x
40GbE QSFP+)

Barracuda CloudGen Firewall
F1000 Revision A 2 / 8
Default Port Configuration
Port Label OS Notation Speed/Type Management Port
MGMT MGMT 10/100/1000 MBit RJ45 X
IPMI n.a. n.a.
Hardware Specifications
Warranty and Safety Instructions
Opening your Barracuda Networks appliance or removing its warranty label unless instructed to
do so by Barracuda Networks Technical Support will void your warranty and hardware support.
Barracuda Networks Appliance Safety Instructions
The CloudGen Firewall hardware appliances ship with a Quick Start Guide. Follow this guide to
connect to your firewall. To protect your network, follow the instructions for the standard
deployment.
Interface
Model CC0 • 16x 1 GbE RJ45 Ethernet
• 4x 10 GbE SFP+
Model CE2 • 32x 1 GbE RJ45 Ethernet
• 8x 10 GbE SFP+
Model CFE
• 16x 1 GbE RJ45 Ethernet
• 16x 1 GbE SFP
• 8x 10 GbE SFP+
Model CFEQ
• 16x 1 GbE RJ45 Ethernet
• 16x 1 GbE SFP
• 6x 10 GbE SFP+
• 2x 40 GbE QSFP+
USB 2.0 2
Serial console 1 [RJ45]
IPMI 1 [RJ45]

Barracuda CloudGen Firewall
F1000 Revision A 3 / 8
Data Storage
RAM [GB] 128
Mass Storage
Type SSD
Size [GB] 550 GB or higher
Size, Weight, Dimensions
Appliance weight [kg] 20
Carton weight with appliance [kg] 26
Appliance size: width x depth x height [mm] 432 x 626 x 88
Carton size: width x depth x height [mm] 590 x 870 x 290
Form factor 2U Rack Mount
Hardware
Display Yes
Cooling Fans, hot swap
Power supply Dual hot swap, internal
Environmental
Noise emission [db/A] N/A
Operating temperature [°C] 0 to +40
Storage temperature [°C] -20 to +75
Operating humidity (non-condensing) 5% to 85%
Non-operating humidity (non-condensing) up to 95%
Altitude during operation [m] up to 2000
Certifications & Compliance
CE emissions Yes
CE electrical safety Yes
FCC emissions Yes
ROHS compliant Yes
FCC Part 15, Subpart B: 2013 Yes
ANSI C63.4-2009 Yes
ICES-003 Issue 5: 2012 Yes
CISPR 22: 2008 Yes
CAN/CSA-CISPR 22-10 Yes
CSA 22.2 No. 60950 / UL 60950 Yes
Power & Efficiency
Power supply type Internal
Power type [AC/DC] AC

Barracuda CloudGen Firewall
F1000 Revision A 4 / 8
Input rating [Volts] 100-240
Input frequency [Hz] 50-60
Auto sense Yes
Wattage / max. power draw [W] 810
Max. power draw (@ 230V) [A] 3.5
Max. heat dissipation [W] 680.4
Max. heat dissipation [BTU] 2321.6
Energy efficiency [average] > 86%
The hardware specifications list was valid at the time this manual was published. The listed
components are subject to change at any time, as Barracuda Networks may change hardware
components due to technological advancements. Therefore, the list may not reflect the current
hardware configuration of the Barracuda Networks CloudGen Firewall or CloudGen Control
Center appliance it was delivered with.
LEDs and Acoustic Signals
Your appliance is equipped with a variety of LEDs. One of them is the Status LED. It is labeled either
with a heart symbol or the term 'Status'. It indicates the appliance’s operational state by changing
colors between green and red and by changing between blinking and steady glowing. The tables
below show the different meanings of the different glowing states and acoustic signals:
LED Color Status Meaning Installation Meaning Operation
All LEDs Off Off
Appliance is powered off or
installation has not initialized far
enough for LED control when
installation is started.
Appliance is powered off.
Power LED front side -
GREEN Steady - Appliance is plugged in and is on.
Status LED front side -
GREEN/RED Off
Installation has not initialized far
enough for LED control when
installation is started.
-
Status LED front side -
GREEN Steady
After a hotfix installation, the LED
turns to green until the next
reboot in case the hotfix
installation was successful. This
feature requires firmware 7.1.3 or
higher OR 7.2.2 or higher.
Box is running normally, or
installation has finished
successfully.

Barracuda CloudGen Firewall
F1000 Revision A 5 / 8
Status LED front side -
GREEN
Blinking
slowly (1/s
interval)
Normal installation.
Appliance is either booting,
shutting down, or
performing a system
update.
Status LED front side -
RED Steady
After a hotfix installation, the LED
turns to red until the next reboot
in case the hotfix installation
failed. This feature requires
firmware 7.1.3 or higher OR 7.2.2
or higher.
Appliance is halted and may
be disconnected, or an
error occurred preventing
the appliance from entering
the up state.
Disc LED front side -
YELLOW Blinking Appliance is reading or writing on storage.
Appliance is accessing the
internal storage.
Port LEDs -
GREEN/YELLOW
Left
blinking
Data transfer – Yellow (10/100
Mbps) Port in use.
Right
steady - Port is on.
PSU LEDs - GREEN
Steady PSU modules connected and
running
Power supply unit is up and
running.
Off Power defective, standby, or
shutdown
Power supply unit is off or in
standby mode.
Acoustic Signal Frequency Meaning Installation
Beep 1 time Unit starts booting
Beep 3 times Installation is completed successfully and appliance is halted for
reboot. After reboot, one beep indicates booting.
Not all appliances support yellow and/or red LED colors. Depending on the appliance type, the
status LED might be on by default and it might take some time during boot and installation to
start either blinking or changing the color. Furthermore, the status LED might blink at different
frequencies.
Serial Console Port
In order to establish a console connection to the appliance using a serial cable, you need to
configure the serial port on the terminal using the following parameters:
Parameter Value
Baud 19200
Bits 8
Stop bit 1

Barracuda CloudGen Firewall
F1000 Revision A 6 / 8
Parity None
Handshake None
LC Display
Navigating
This security appliance features a key pad with four keys and an LCD panel on the left side of the
front panel. These may be used to obtain certain information and to perform certain commands
directly on the appliance.
Keyboard Button Command
Left arrow Navigates back or acts like an Escape key while working in the LCD menu.
Up arrow Navigates up or increases a value.
Down arrow Navigates down or decreases a value.
Right arrow Navigates forwards or acts like an Enter key for confirming a configuration step.
LCD Display Menu
You may use the LCD display and the keypad to access certain appliance features. Use the up
and down keys to navigate through the items of the main menu.
The LCD menu features the following items from top to bottom:
LCD Menu Meaning
Appliance type, OS version and
release number This is the default display.
IP address and subnet mask Shows the configured IP address and subnet mask of the
appliance.
Time and date Shows time and date currently configured on the appliance.
Uptime of Barracuda OS The uptime in days, hours and minutes.
Serial number of the appliance Unique identifier for the appliance.
Shutdown menu Enables you to shut down the appliance.
Reboot menu Enables you to reboot the appliance.
Menu to change the management
IP address Configure the IP address for the management port.

Barracuda CloudGen Firewall
F1000 Revision A 7 / 8
Menu to boot into ART during
the next reboot
Enables you to set a flag that will cause the appliance to boot into
ART the next time it is rebooted.
Once set, this flag can not be deleted through the menu. When
rebooted, the appliance will not start Barracuda OS, but ART
instead. You may connect to the appliance by using the serial
console or by SSH. A Control Center managed box running in ART
mode cannot be managed through the CC, although it will build a
connection to the CC signalling its presence.

Barracuda CloudGen Firewall
F1000 Revision A 8 / 8
Figures
F1000.CE0_FrontRack.png1.
F1000.back.png2.
F1000.CE2_FrontRack.png3.
F1000.CFE_FrontRack.png4.
F1000.CFEQ_FrontRack.png5.
© Barracuda Networks Inc., 2021 The information contained within this document is confidential and proprietary to Barracuda Networks Inc. No
portion of this document may be copied, distributed, publicized or used for other than internal documentary purposes without the written consent of
an official representative of Barracuda Networks Inc. All specifications are subject to change without notice. Barracuda Networks Inc. assumes no
responsibility for any inaccuracies in this document. Barracuda Networks Inc. reserves the right to change, modify, transfer, or otherwise revise this
publication without notice.