Trend Micro txOne Networks EdgeIPS User manual

EdgeIPS
Quick Setup Guide
EdgeIPS is a Transparent Security Box fitted with dual Ethernet LAN ports. Users
can efficiently adapt the palm-sized EdgeIPS into a flexible solution for the
challenges of Ethernet communications.
1. Opening and Inspecting the Package
Verify that the EdgeIPS package contains the following items:
2. Examining the EdgeIPS
3. Deployment Checklist
4. Deployment Scenario and System Operation Mode
Requirement
Details
Ethernet Cables
- Connect to the port 1 for accessing web console management.
- Connect to the port 2 to swtich or filed device.
Default IPAddress of
web console
Default web console access information:
https://192.168.127.254
User name: admin
Password: txone
Laptop with Ethernet
Port (RJ-45 Type)
The computer must have one of the following browsers installed:
- Microsoft Edge (version 15 or above)
- Firefox (version 53 or above)
- Safari (version 10.1 or above)
- Google Chrome (version 63 or above)
Mode
Description
Inline mode
In inline mode, EdgeIPS is installed directly in the path of traffic.
Offline mode
In offline mode, EdgeIPS connects to a mirror port of network switch and
mirrors traffic to itself.
EdgeIPS Front Panel
EdgeIPS Back Panel
EdgeIPS Appliance
Console Cable (USB-Type-C) x1
Terminal Block x 1
Documents
DIN Rail mount kit (assembled to EdgeIPS)

5. LED Indicators
The function of each LED is described in the table below
LED Name
Status
Function
PWR1
Amber
Power 1 is ON
Off
Power 1 is OFF
PWR2
Amber
Power 2 is ON
Off
Power 2 is OFF
MANAGED
Green
OT Defense Console Sync (ODC) is
enabled and ODC is connected
Off
OT Defense console sync is disabled
IPS/IDS
Green
IPS and IDS enabled
Off
IPS and IDS disabled
USB/F
Green
LED will be turned on when USB is plugged
in
Red
Hardware or system fault
Blinking
USB data transmission
BYPASS
Amber
Hardware bypass mode enabled
Off
Hardware bypass mode disabled
6. Reset to factory default setting
The reset button for the EdgeIPS is located on the front panel.
Reset type
Description
Reboot System
Press and hold the reset button for 2 to 10 seconds. The MANAGED LED will begin
to blink on a 1-second pattern, which means the system is rebooting.
Restore Factory
Default Settings
Press and hold the reset button for more than 10 seconds. The MANAGED LED will
begin to blink every half-second, which means the system is resetting itself to
factory defaults.
7. Installing the EdgeIPS
DIN Rail Mounting
The aluminum DIN Rail attachment plate should already be fixed to the back panel of
the EdgeIPS when you take it out of the box. If you need to reattach the DIN Rail
attachment plate to the EdgeIPS, make sure the stiff metal spring is oriented towards
the top, as shown in the following pictures.

8. Wriing the Redundant Power Inputs
The Trend Micro EdgeIPS has two sets of power inputs –power input1 and power input2. The
top and side views of the terminal block connector are shown below.
STEP 1:
Open the terminal block’s wire locks by pushing the buttons down.
STEP 2:
Insert a positive / negative DC wire into the V+/V- terminals
respectively.
STEP 3:
When the wire is properly seated, the wire lock will be forced shut
around it. Check whether the wire is properly fixed.
9. Connecting the Power
Connect the 12 to 48 VDC power line to the terminal block, which is connected to the EdgeIPS
device. If the power is supplied properly, the “Power” LED will glow steadily. The power input
location and pin definition are shown in the following diagram.
10. Grounding the Unit
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the terminal block connector to the grounding surface
prior to connecting the power. Please note that this product is intended to be mounted on a
well-grounded mounting surface, such as a metal panel. The minimum cross-sectional area of
the conductor must be equal to the input wiring cable’s width/circumference.
11. Software Configuration
Before connecting the PC/Laptop to EdgeIPS, the PC's IP address should be set to
192.168.127.100. After that, connect the PC and EdgeIPS using an Ethernet cable. Open a
web browser on your PC and type “https://192.168.127.254” into the address bar. A pop-up
window will open to ask for user name and password. Please type the default username,
“admin”, and password, “txone”.
Now, the main screen will pop up so you can configure EdgeIPS.

12. Setting the Management IP Address
1. Go to [Device] > [Device Setting]
2. In the [Network Setting] plane, configure management IP address for EdgeIPS
Task
Action
Device IP Address
Configure Management IP Address of the EdgeIPS
Netmask
Configure Netmask of the EdgeiPS
Gateway
Confiture GatewayAddress of the EdgeIPS
DNS
Configure DNS setting of the EdgeIPS
Network VLAN-ID
Configure Network VLAN-ID of the device
13. Connecting to the Network
EdgeIPS’s ports 1 and 2 make up a network segment.
1. Port 1 is a “mixed” port design, functioning both as the management console port and to
connect to a network node, so EdgeIPS’s Port 1 can be connected either to your network
switch/hub or to a laptop. Connecting this port to the network enables remote management
of the device.
2. EdgeIPS’s Port 2 links the IPS to the device or small production zone you are targeting for
protection.
14. Checking the LED to Confirm Status
The LED on each Ethernet port shows the deployment status.
RJ45 LED Indication
Status
No Light
The EdgeIPS appliance cannot communicate with a
network.
Left LED0:(Green)
GE LNK/ACT (off = no link, on = 1 Gbps Link, blinking =
activity)
Right LED1:(Green)
10/100Mbps LNK/ACT (off = no link, on = 10/100 Mbps
Link, blinking = activity)
15. Contact Information
Website: https://www.trendmicro.com
List of worldwide offices and phone numbers:
https://www.trendmicro.com/us/about-us/contact/index.html
Technical Support page
https://success.trendmicro.com/.
EULA
https://www.trendmicro.com/en_us/about/legal.html
© 2019 Trend Micro Incorporated. All Rights Reserved. Trend Micro and the t-ball logo are trademarks or
registered trademarks of Trend Micro Incorporated. All other company and/or product names may be
trademarks or registered trademarks of their owners. Information contained in this document is subject to
change without notice.

Appendix : Connecting to the Console Port
The EdgeIPS console port is a USB Type–C Port located on the front panel of the
case. It is designed for connection to serial console terminals for viewing
messages during the boot sequence or for debugging system boot issues. To
connect the console cable, remove the protective cover on the port.
Serial Console Port, Cable & Pinouts
The initial configuration for the EdgeIPS using the command line interface (CLI) on a
serial terminal client will use the following default settings:
• Baud Rate: 115200 bps
• Character size: 8 bits
• Parity: None
• Stop Bits: 1
• Flow Control: None