Bartscher M 7110G User manual

M 7110G / 1166281
M 10110G / 1166311
Original-Gebrauchsanleitung
V1/0516

- 39 -
ENGLISH
Table of contents
1.Safety ........................................................................................................................ 40
1.1 Important safety instructions................................................................................. 40
1.2 Key to symbols..................................................................................................... 44
1.3 Proper use............................................................................................................ 45
2. General information................................................................................................ 46
2.1 Liability and Warrantees....................................................................................... 46
2.2 Copyright protection ............................................................................................. 46
2.3 Declaration of conformity...................................................................................... 46
3. Transport, packaging and storage......................................................................... 47
3.1 Delivery check...................................................................................................... 47
3.2 Packaging............................................................................................................. 47
3.3 Storage................................................................................................................. 47
4. Technical data......................................................................................................... 48
4.1 Combi steamer properties.................................................................................... 48
4.2 Technical specification ......................................................................................... 49
5. Installation and operation....................................................................................... 52
5.1 Instructions for the installer................................................................................... 52
5.1.1 Installation instructions ........................................................................... 52
5.1.2 Installation place..................................................................................... 53
5.1.3 Preparing for Installation......................................................................... 53
5.1.4 Electrical connection............................................................................... 54
5.1.5 Water connection.................................................................................... 55
5.1.6 Drain connection..................................................................................... 56
5.1.7 Connecting to a gas line......................................................................... 56
5.1.8 Activation and acceptance of gas devices.............................................. 61
5.2 Instructions for the user........................................................................................ 63
5.2.1 Safety notes............................................................................................ 63
5.2.2 Operation................................................................................................ 64
5.2.3 Functions of the control elements and displays...................................... 65
5.2.4 Settings................................................................................................... 66
5.2.5 Tips and advice....................................................................................... 72
6. Cleaning and maintenance..................................................................................... 72
7. Possible Malfunctions ............................................................................................ 75
8. Waste disposal........................................................................................................ 76
Bartscher GmbH
Franz-Kleine-Str. 28
D-33154 Salzkotten phone: [phone]
Germany fax: [phone]
GB/UK

- 40 -
Read this instruction manual before using and
keep them available at all times!
This instruction manual contains information about the installation, operation and
maintenance of the device and should be consulted as an important source of
information and reference guide.
Awareness of the safety instructions and instructions for use in this manual will ensure
the safe and correct use of the device.
In addition to the information given here, you should comply with any local Health and
safety Controls and generally applicable safety regulations.
The instruction manual forms part of the product and should be kept near the device
and easily accessible for anyone carrying out the installation, servicing, maintenance or
cleaning.
Please keep these instructions and give them to future owners of the device.
1.Safety
This device is designed in accordance with the presently applicable technological
standards. However, the device can pose a danger if handled improperly and
inappropriately.
All persons using the device must follow the recommendations and instructions
in this instruction manual.
1.1 Important safety instructions
• The device is not intended for use by individuals (including children)
with physical or mental disabilities, insufficient experience, and/or
insufficient knowledge unless such persons are under the care of a
person responsible for their safety or have received instructions
regarding appropriate use of the device.
• Children should be observed to ensure that they are not playing with
the device.
• Never leave the device unattended when in use.
• Only use the device indoors.
• The device is not adapted for use with an external timer or remote
control.
• This device may only be operated in technically proper and safe
condition.

- 41 -
•
Prevent access of children to the package materials like plastic bags
and foamed polystyrene elements. Suffocation hazard!
• Only a qualified technician and using original spare parts and
accessories should carry out repairs and maintenance of the device.
Do not attempt to repair the device yourself.
• Do not use any accessory or spare parts that have not been
recommended by the manufacturer. These can be dangerous for the
user or lead to damages of the device or personal injury, and further,
the warranty expires.
• To prevent hazards and to ensure optimum efficiency, no modifications
or alterations to the device that are not explicitly approved by the
manufacturer may be undertaken.
DANGER! Electric shock hazard!
To avoid the hazard results please follow the safety instructions below.
• Never allow the power cable to come into contact with heat sources or
sharp edges. The power cable should not hang over the side of the
working surface. Ensure that no one can step on or trip over the cable.
• The power cable must not be folded, bent or tangled, and must always
remain fully unrolled. Never place the device or other objects on the
power cable.
• Do not lay the cable over carpets or heat insulations. Do not cover
the cable. Keep away the cable from operating range and do not
dunk it into water.
• Inspect the power cable regularly for damage. Never use the device
if the cable is damaged. If the power cable is damaged, have an
authorised service center or qualified electrician replace it.

- 42 -
•
Never open the housing of the device. If the electrical connections
are damaged or electrical or mechanical design is changed, there is
a risk of electrical shock.
• Never immerse the connecting cable and the the power plug in water
or other liquids.
• Never use abrasive agents and make sure no water gets into the
device.
• Never handle the device with wet hands or while standing on the wet
floor.
• Disconnect the device from the power supply:
-when the device is not used,
-in the case of interruptions during the operation of the device,
-before cleaning the device.
HOT SURFACE! Danger of burns and injury!
To avoid the hazard results please follow the safety instructions below.
• During operation, the surface of the device becomes very hot! Do not
touch the hot surface of the device with bare hands! Hold the device
during operation only at the handles and control elements envisaged
for this.
• Even after switching off the surface of the device and the cooking
space as well as food in the containers remain hot for quite some
time. In order to take out the food from the cooking space, always
apply thermal gloves.
• In the course of opening the combi steamer door the hot steam can
may escape, so be particularly careful.
• Let the device cool down sufficiently before cleaning it.

- 43 -
Hot liquid in container! Danger of burns!
To avoid the hazard results please follow the safety instructions below.
• When preparing the meals or liquids that are in the containers you
should remember that they can boil over or splatter, both while
cooking and when removing the containers from the steamer oven
cooking compartment.
It is recommended to use the levels where the user can see the
inside of the containers.
WARNING! Fire or explosion hazard!
To avoid the hazard results please follow the safety instructions below.
• Make sure before using the device that there are no objects, such as
plastic bags, instruction manual and accessories, located in the
cooking space. Never place during operation any kitchen utensils,
towels, paper and similar into the cooking space and on the device.
• Make sure that the steam outlet is not blocked or plugged.
• Never operate the device in the vicinity of flammable, easily ignited
(e.g. gasoline, spirit, alcohol, etc.). Due to the heat they evaporate and
in case of contact with ignition sources it can come to explosionen,
which lead to serious personal injury and property damage.
• Reinigen Sie den Garraum regelmäßig und halten ihn immer sauber:
die nicht entfernten Fette und Backrückstände können sich
entzünden. Clean the cooking space regularly and keep it always
clean: fats and baking residues which are not removed, can ignite.
• Should a fire occur, disconnect the device from the power supply
(pull out the power plug!) initiate appropriate fire fighting measures.
Attention: Do not pour water onto the device still being under
voltage: danger of electric shock!

- 44 -
1.2 Key to symbols
In this manual, symbols are used to highlight important safety instructions and any
advice relating to the device. The instructions should be followed very carefully to avoid
any risk of accident, personal injury or material damage.
WARNING!
This symbol highlights hazards which could lead to injury.
WARNING!
This symbol highlights dangerous situations which could lead to injury or death.
HOT SURFACE!
This symbol is a warning that the device surface is hot when in use.
Ignoring this warning may result in burns!
Hot liquid in container! Danger of burns!
When containers hold liquid or products that turn liquid during cooking, do not
higher shelves to place the containers so that the operator can always look into
the container inside.
CAUTION!
This symbol highlights dangerous situations which could lead to light
injuries, or damage, malfunction, and/or destruction of the device.
NOTE!
This symbol highlights recommendations and information aimed for effective
and trouble-free device operation.

- 45 -
1.3 Proper use
CAUTION!
This device has been designed and built for commercial use and can be
operated in kitchens by the qualified personnel only!
The operational safety of the device is assured only in case of proper use, according
to the operation manual.
All technical activities like installation and maintenance must be performed by the
qualified service personnel only.
The combi steamer is intended only for preparation of appropriate food products.
CAUTION!
Any use going beyond the intended purpose and/or any
different use of the device is forbidden and is not considered as
conventional.
Any claims against the manufacturer or his authorized
representative as a consequence of experiencing damages
resulting from unconventional use are impossible.
The operator is liable for all damages resulting from
inappropriate use.

- 46 -
2. General information
2.1 Liability and Warrantees
All the information and instructions in this manual take into account standard safety
regulations, current levels of technical engineering as well as the expertise and
experience we have developed over the years.
The instruction manual was translated with all due care and attention. However, we do
not accept liability for any translation errors. The German version of this instruction
manual is definitive.
If the delivery consists of a special model, the actual scope of delivery may differ from
the descriptions and illustrations in this manual. This is also the case for special orders
or when the device has been modified in line with new technology.
CAUTION!
Read this manual carefully and thoroughly before any operation
of the device, and especially before turning it on!
Manufacturer is not liable for any damages or faults caused by:
-violation of advice concerning operation and cleaning;
-use other than designed;
-alterations made by user;
-use of inadequate spare parts.
We reserve the right to make technical changes for purposes of developing and improving
the useful properties.
2.2 Copyright protection
The instruction manual including any texts, drawings, images or other illustrations is
copyright. No part of this publication may be reproduced, transmitted or used in any
form or by any means without permission in writing from the manufacturer. Any person
who commits any unauthorized act in relation to this publication shall be liable to claims
for damages. All rights reserved.
NOTE!
The contents, texts, drawings, pictures and any other illustrations are
copyright and subject to other protection rights. Any person unlawfully
using this publication is liable to criminal prosecution.
2.3 Declaration of conformity
The device complies with the current standards and directives of the EU.
We certify this in the EC declaration of conformity. If required we will be
glad to send you the according declaration of conformity.

- 47 -
3. Transport, packaging and storage
3.1 Delivery check
Please check the delivery upon completeness and transport damage immediately
after receipt. In case of visible damage do not accept or accept the delivery with
reservation only.
Note the extent of damage on the carrier’s bill of delivery. Trigger off the complaint.
Hidden damages should be reclaimed immediately after notice, as claims for damages
can only be asserted within the effective period for complaints.
3.2 Packaging
Please do not throw away the covering carton of your device as it might be useful for
storage purposes, when moving or, in case of damages, when the device must be sent
back to a repair center. The outer and inner packing material should be removed
completely from the device before installation.
NOTE!
If you liked to dispose the packing, consider the regulations applicable in
your country. Supply re-usable packing materials to the recycling.
Please inspect the device upon completeness. In case any part is missing please
contact our customer service center immediately.
3.3 Storage
Keep the package closed until installation and under consideration of the outside
indicated positioning- and storage markings.
Packages should be stored under consideration of the following:
-Do not store outdoors.
-Keep it dry and dust-free.
-Do not expose it to aggressive media.
-Do not expose it to direct sunlight.
-Avoid mechanical shocks and vibration.
-In case of longer storage (> 3 months) make sure you check
the state of the packaging and the parts regularly.
If required refresh or renew.

- 48 -
4. Technical data
4.1 Combi steamer properties
•Produced from 18/10 chrome-nickel steel
•Operated by dials
•Maximum capacity of 10 1/1 GN or 600 x 400 mm baking trays
•Functions: recirculated air, steam cooking, convection-cooking
•Reversing engine direction (clockwise and counter clockwise rotation) ensuring
optimal cooking compartment temperature
•Two-speed fan regulation
•Direct-injection steaming
•Steam extractor, adjustable
•Cooking compartment light
•LED internal temperature display
•Prepared to install a core temperature sensor (116009)
•Prepared to mount manual spray (116005)
•Dual pane glass door, easy access to the oven interior for cleaning
•Removable inside guide rails
Safety features
The device is equipped with the following security and safety features:
Safety thermostat in the cooking compartment: if the cooking compartment overheats,
the safety thermostat is activated and the supply of electricity to hearing elements is
interrupted.
CAUTION!
The safety features can only be reactivated by qualified service personnel,
as further control measures must be performed.
The door switch interrupts the device’s functioning when the door is open: the heating
and circulation systems are turned off.

- 49 -
4.2 Technical specification
Name Gas steam convection oven
Model:
M 7110G M 10110G
Code-No.:
1166281 1166311
Capacity: max. 7 x 1/1 GN
or 600 x 400 mm bakery trays
max. 10 x 1/1 GN
or 600 x 400 mm bakery trays
Distance between
trays: 74 mm
Temperature range: 50 °C – 280 °C
Power gas: R 1/2“ 16.5 kW R 1/2“ 19.0 kW
Power electric: 0.8 kW / 230 V 50 Hz 0.8 kW / 230 V 50 Hz
Water connection: 3/4“
Water pressure: max. 3 bar
Dimensions: W 890 x D 850 x H 930 mm W 890 x D 850 x H 1150 mm
Weight: 119.8 kg 137.8 kg
Equipment: 1 grille 1/1 GN, 1 tray 1/1 GN
1 exhaust pipe, 1 pressurised water hose
We reserve the right to make technical changes!

- 50 -
Additional equipment (not included with device)
Core temperature sensor set STL
The set includes the core temperature sensor and
relevant handle to fix it at the combi steamer
• Cord length: approx. 1.8 m
• Magnetic handle: W 130 x D 35 x H 30 mm
• Weight: 0.57 kg
Code-no.: 116009
Hand sprayer
Hose length: 2 m
with the cut-off valve for the 1/2" rigid water supply
and the handle to fix it at the combi steamer
Code-no.: 116005
1 pair of standardised rails for bakeries
to use with 7 bakery trays 600 x 400
for combi steamer 1166281
Code-no.: 116002
1 pair of standardised rails for bakeries
to use with 10 bakery trays 600 x 400
for combi steamer 1166311
Code-no.: 116003

- 51 -
Safety pressure stop for
convection ovens
and
combi steamer
• Made of chromed brass
• 3/4” connector
• Initial setting at 3 bar, adjustable from 1 to 6 bar
• Input pressure max. 16 bar
• Maximum working temperature 65 °C
Code-no.: 533051
Base for combi steamer 1/1 GN
• Chrome-nickel steel 18/10
• Possible arrangement: 10 x 1/1 GN
• Size: W 850 x D 700 x H 741 mm
• Weight: 25 kg
Code-no.: 115069

- 52 -
5. Installation and operation
5.1 Instructions for the installer
CAUTION!
Any operation related to installation, assembly, operation and maintenance
must be performed by the specialized personnel who has appropriate
qualifications (manufacturer’ or seller’s authorisation). The required activities
need to be performed while taking into account the installation regulations
valid in a given country as well as the product safety legislation and health
and safety regulations.
5.1.1 Installation instructions
•Before the installation and the use of the device, read carefully these operating
instructions.
•Defective installation, mistakes during the operation, conservation and cleaning, as
well as possible changes and modifications may cause improper operation, damages
and injuries.
•Manufacturer will not assume any liability for personal injuries or material damages
resulting from the failure to observe the aforementioned regulations or tampering
with single components of the device or using non-original spare parts.
•Immediately after receiving the device, make sure that it has not been damaged in
transit, and that the packaging is not damaged. In the case of damage or missing
components, immediately notify the shipper or vendor/manufacturer providing the
code-no. and serial numbers (nameplate is on the back of the unit) and attaching
photo evidence.
•Make sure that there are no obstacles on the path to the installation site limiting
access through doors, corridors or other communication routes.
•NOTE: During the transport of the device, it may turn over, which might result in the
damage to the device itself or other objects or in personal injuries. During the
device’s transport, use the measures appropriate for its weight. The device should
not be pulled or tipped, but lifted perpendicularly to the floor and moved horizontally.

- 53 -
5.1.2 Installation place
•The device must be installed in closed and well ventilated rooms (not outdoor).
•Check the dimensions and the exact position of connections for electricity, water and
extractor connections before installation of the combi steamer.
•We recommend to install the device under an extractor or to ensure the discharge
outside the hot vapours and odours which emerge from the cooking space.
•The devicemust be installed on a flat surface in order to prevent it from slipping or
tipping.
•The installation surface of the combi steamer must be suitable for the weight of the
device at maximum load.
•Place the device unit on a firm, dry, water-resistant and heat-resistant surface.
The installation surface must be well accessible and big enough to be able to
operate freely with the device and to ensure good air circulation.
•Install the device in such manner that the rear part is easily accessible in order to
allow the electricity and water connections and maintenance.
•Never place the device directly against walls, kitchen furniture or other flammable
objects. Proceed according to relevant fire safety regulations.
•Keep a minimum of 100 mm between the device and walls/other objects on the left
and right sides and at the rear, and 150 mm from the top.
•The device is not designed to be built-in!
5.1.3 Preparing for Installation
•Remove the external packaging (wooden box and / or carton) and dispose them in
accordance with the applicable provisions of the installation country.
•Before first use, remove the protective foil from the device. Peel the foil off slowly, so
as not to leave any glue. If some glue remains, remove it using an appropriate
solvent.
•Remove from the internal accessories, all information materials and plastic bags.
CAUTION!
Never remove the nameplate and warning notes from the device.

- 54 -
Adjustment of the feet
•The adjustable feet are enclosed to the device and must be screwed under the
device. The correct flatness of the device ensures a smooth operation. This flatness
is obtained by adjusting the feet and verification by a spirit level. It is sufficient, to
screw them in or screw out to change their settings.
CAUTION!
Do not use the device without adjustable feet!
•If the device is operated without adjustable feet, no air passage for cooling the
electronic components and the external walls of the housing is ensured, this could
cause overheating and result in damage of the components of this device.
5.1.4 Electrical connection
DANGER! Danger from electric current!
Improper installation of the device may result in injuries!
Prior to installation, compare specification of the local power network
with the technical specifications of the device (see nameplate).
Connect the device only in case of conformity!
•Before connecting the device to an electricity source, ensure that the voltage and
frequency values given on the panel correspond to those of the electrical network.
The maximum permissible voltage difference is ± 10%.
•Check if there is an SL connection fulfilling legal requirements. Use an appropriately
cut cable when connecting the device to electricity.
•A multipolar breaker must be installed between the device and the electricity supply.
The distance between contacts should be at least 3 mm, and it should be located in
an easily-accessible place.
•Connect the device to the electricity supply in compliance with all international,
domestic and local regulations.
•Place the device in such a position to make the plug available to easy unplug it,
if necessary.

- 55 -
Potential difference connection
•Installation for connection of device of different potentials using the clip
indicated as . The clip is located at the rear of the device.
•The clip is used to connect the potential difference wire (yellow-green) of a diameter
from 4 to 10 mm
2
.
•The device should be connected to the potential difference circuit of the efficiency
according to the recommendations included in the current legal regulations.
5.1.5 Water connection
•Ensure that the device is located near water connections.
•If a new installation is to be put in, flush it out with water to remove all dirt and
impurities before connecting the device so as to protect the magnetic valves.
•Connect the pressurised water hose (included) using the 90°connection bevel to
the connector (3/4“) of the device. Location of the connector: at the rear, at the
right side under the device. Connect the other end of the pressurised water hose
to the cold water network with the stopcock.
CAUTION!
Hydraulic pressure cannot exceed a maximum of 3 bars.
Use a reducing valve for higher pressures.
•To ensure the device functions properly and prevent the formation of deposits in the
water boiling compartment, the water hardness can measure not more than 7°dH .
CAUTION!
If water hardness is above 7 °dH, it is necessary to install a water softening
mechanism.

- 56 -
5.1.6 Drain connection
•At the condensate-collecting tray located in
front of the oven, there is a drain hose (with
an inner diameter of 10 mm). This hose drains
excess liquids from the condensate-collecting
tray away and runs in the rear part below the
device (see A- picture on the right). To drain
the water to the drainage system, extend the
available hose as needed.
•Fasten the supplied drain pipe to the outlet
hole located under the device to ensure the
outflow of liquids from the cooking
compartment.
The drain pipe must be connected with a suitable
hose (∅ 22 mm) to the drainage system.
5.1.7 Connecting to a gas line
Connect gas devices to a gas line using a
special R 1/2" pipe with a minimum internal
circumference of 16 mm.
Use metal connections and a hose or tube.
Use stopcocks or bolts with an internal
circumference at least equal to the internal
circumference of the connection pipe
described above.
After connecting to the gas supply check
that all seals and connections are airtight by
using soap suds or another foam-producing
product to find any leaks.
Gas devices must be serviced by service personnel once a year, in accordance
with the relevant legal regulations. Maintenance includes an emissions analysis
and check of the heating device’s efficiency.
A

- 57 -
CAUTION!
The device only functions properly when the pressure in the gas installation
is within the values presented in the table below for various gas types.
Country of destination Categories Type of gas
Gas pressure
(mbar)
AL Albania
II
2H3+
II
2H3B/P
G20 - G30/G31 20 - 28-30/37
20 - 30/30
AT Austria II
2H3B/P
G20 - G30/G31 20 - 50/50
BE Belgium II
2E+3+
G20 - G30/G31 20/25 - 28-30/37
BG Bulgaria II
2H3B/P
G20/G25 - G30/G31 20 - 30/30
CY Cyprus
II
2H3+
II
2H3B/P
G20 - G30/G31
G20 - G30/G31 20 - 28-30/37 20 - 30/30
HR Croatia II
2H3B/P
G20 - G30/G31 20 - 30/30
DK Denmark II
2H3B/P
G20 - G30/G31 20 - 30/30
EE Estonia
II
2H3B/P
G20 - G30/G31 20 - 30/30
FI Finland
II
2H3B/P
G20 - G30/G31 20 - 30/30
FR France II
2E+3+ G20/G25 - G30/G31 20/25 - 28-30/37
DE Germany II
2ELL3B/P G20 - G25 - G30/G31 20 - 20 - 50/50
GR Greece
II
2H3+
II
2H3B/P
G20 - G30/G31
G20 - G30/G31 20 - 28-30/37 20 - 30/30
IE Ireland II
2H3+ G20 - G30/G31 20 - 28-30/37
IS Iceland I
3B/P G30/G31 30/30
IT Italy II
2H3+ G20 - G30/G31 20 - 28-30/37
LV Latvia II
2H3B/P G20 - G30/G31 20 - 30/30
LT Lithuania
II
2H3+
II
2H3B/P
G20 - G30/G31
G20 - G30/G31 20 - 28-30/37 20 - 30/30
LU Luxembourg I
2E G20 20
MT Malta I
3B/P G30/G31 30/30
NO Norway II
2H3B/P G20 - G30/G31 20 - 30/30
NL Netherlands II
2L3B/P G25 - G30/G31 25 - 30/30
PL Poland II
2ELwLs3B/P G20 - G27 - G2:350
G30/G31 20 - 20 - 13 - 37/37
PT Portugal II
2H3+ G20 - G30/G31 20 - 28-30/37
GB United Kingdom II
2H3+ G20 - G30/G31 20 - 28-30/37