Basalte CHOPIN KNX User manual

Installation Manual
© 2020 basalte v1.0
1
2
3
4
CHOPIN KNX
ARGB LED’s
BProgram button
CProgramming LED
D Temperature sensor connector pins*
*The sensor is located in the Chopin cover plate
(not included).
*2-gang covers only have one temperature
sensor, check the back of the cover to verify its
position.
E Opening to screw the Chopin switch to the wall
box
F Clips to mount the cover plate
G Alignment guides for 2-gang installations
Safety instructions
Before operating the unit, please read this manual thoroughly and retain it for future reference.
Failure to observe these instructions might damage the device.
The device may only be installed and connected by professional electrical contractors.
All relevant rules and regulations valid in the country of use, as well as KNX guidelines, apply.
Description
Chopin KNX is a mechanical switch compatible with all Chopin cover plates, both 1- and 2-gang.
The Chopin’s levers control various functions, using both short and long press.
Additional comfort functions can be activated including room toggle, scene sequencer and RGB sequencer. The
multicolour LED backlight provides status feedback and can be used as night light.
The Chopin KNX also has a built-in temperature sensor and integrated thermostat logic. A scene controller can
control up to 6 scenes and 8 outputs per scene.
Components
Chopin KNX
Model No. 0220-02
Compatible Chopin covers
Visit chopin.basalte.world to
configure your Chopin cover.
When using vertical oriented Chopin covers, the clips to mount the cover plate need to be oriented
vertically. Make sure to click out electronics from the socket adapter and turn the electronics 90°
counter-clockwise.
E
E
A
B
H
H
F
F
F
F
D
C
G
11
22
33
44
11
22
33
44
11
22
33
44
11
22
33
44
11
22
33
44
11
22
33
44

Installation and commissioning
• Use a standard European back box with screws. The distance between the screws needs to be 60mm. The
required depth is 30mm, although additional depth should be reserved for connecting the device.
For 2-gang Chopin, use a 2-gang European back box with a centre to centre distance of 71mm.
To verify your compatible back box, please refer to the back box application note on basalte.world.
• Mount the Chopin with the programming button upwards. Use screws with a countersunk, flat head.
• Connect the switch to the KNX bus according to the KNX guidelines.
• Load the physical address into the Chopin switch from ETS via the KNX bus.
• Commission the Chopin switch using ETS and load the configuration into the device.
• Please refer to the software manual to configure the Chopin switch.
Do not apply too much force screwing Chopin electronics to the backbox, otherwise you risk the levers to
not function properly.
How to mount the Chopin front cover (not included)
How to remove the Chopin cover (not included)
dPush the cover upwards
eTilt the cover away from the wall
d
e
Installation Manual
© 2020 basalte v1.0
CHOPIN KNX
aPlace the Chopin front cover over the lower clips
bPush the Chopin front cover upwards and tilt
towards the wall
cAttach the Chopin front cover over the top clips
Pushing the cover straight
into the clips without
pushing upwards and lifting
might damage the Chopin
electronics. a
b
c
1
2
3
4
basalte bv | hundelgemsesteenweg 1A | 9820 merelbeke | belgium
t [phone] | f [phone] | www.basalte.be | [e-mail]
Technical data
Current consumption KNX bus: 10mA
Ambient temperature:
Operation: -5°C to 45°C
Storage: -15°C to 55°C
Transport: -15°C to 55°C
Max. humidity: 93% relative humidity,
no moisture condensation
Protection class: II
Type of protection: IP 20
Certification: CE