BASI TS700 Quick reference guide

Digital Door Viewer
TS 700
facebook.com/BASI GmbH @basi_gmbh www.basi.eu
ASSEMBLY/OPERATING INSTRUCTIONS
For house entrance and apartment doors
Generous display
Wide-angle lens

Intended use
Read the usage and maintenance in-
structions carefully before mounting the
spyhole. Keep the manual with you for
future use. If the product is passed on to
any third party, include the manual withit.
Warnings: There should be no dangers
whatsoever expected in the pro-
fessional assembly and operation
compliant with the instructions.
Small parts and packaging mate-
rials can be swallowed by children
and lead to choking! Make sure that small
parts and packaging materials do not get
into the hands of children. Dispose of the
packaging material immediately.
Please read these operating instructions
before using the device. The camera or
main body MUST NOT be dismantled.
Please handle the device carefully. In or-
der to prepare for the assembly, please
loosen the two screws on the lower side
of the viewer, take out the retaining plate
and remove the protective film.
The manufacturer expressly reserves the
right to make technical changes.
Disclaimer
The manufacturer accepts no liability for
damage or injury resulting from incorrect
handling.
Disposal
Help to protect the environment
and dispose of the product and the
packaging materials in accordance with
the local regulations. Do not dispose of
the device in household waste! Electronic
devices must be disposed of in accord-
ance with the directive on waste electri-
cal and electronic equipment via the lo-
cal collection points for waste electronic
equipment!
BEFORE THE ASSEMBLY:
Please put in the battery first before you
install the door viewer.
Assembly:
Step 1:
Remove the retaining plate of the digi-
tal door viewer by loosening the 2 lower
fastening screws and put in the batteries
properly.
Step 2:
Remove existing viewer or drill a 14 mm
wide hole in the door at eye level. Put in
the camera form outside and simultane-
ously place the washers between back of
the lens and the door. Make sure that the
arrow at the front of the camera points
upwards.
Step 3:
Now route the camera’s connection ca-
ble withe the plug on the inside of the
door through the retaining plate.
Place
the retaining plate over the end of the
camera lens and then screw the fasten-
ing cylinder on the camera threads; this
will fasten the place on the door. You can
now secure the plate with two or three
screws (enclosed). Make sure that the ar-
row on the plate points upwards.
Step 4:
The camera’s connecting wire should
now be properly connected at the
bushing at the back of the door view-
er (see WARNING); excess wire should
be fastened behind the small hook.
General notes

Step 5:
Hook the digital door viewer in the
clamp above on the retaining plate (ar-
row upwards) and fasten the viewer by
inserting the two small screws through
the opening below on the housing of
the viewer and tighten the screws.
Scope of delivery:
1) Digital door viewer with retaining plate
2) 3 screws
3) Camera with fastening cylinder
4) Washer
5) Fastening tool
6) 4 AA batteries
Operation:
1.Switch on/off button: Press and release
the button; the device is then activated
for 10 seconds.
2.Display lamp: If the display lamp lights
up, please replace the batteries.
Door
1
2
1
2
Switch On/
Off button
Technical specifications
For house and apartment front doors
Suitable for doors with a door thickness of 38 - 70 mm
Installation diameter: 14 - 22 mm
LCD screen 3.5” thin-film transistor Sensor 0.3 megapixel CMOS
Batteries 4 AA batteries Wide-angle lens 110°
Product size 135 mm (width) x 85 mm (height) x 24.5 mm (depth)
ABOVE
Door
Hang
Screw

Scope of delivery:
© Copyright
Reprint or copy (even in excerpts) may
be made only with the permission of:
BASI GmbH
Konstantinstrasse 387
41238 Mönchengladbach
Germany
2023
This publication, including all its parts, is
protected by copyright.
Any use outside the strict limits of
copyright without the consent of BASI
GmbH is not permitted and punishable.
This applies in particular to duplications,
translations, microfilming and the
feeding and processing in electronic
systems.
WARNING!
IMPORTANT ASSEMBLY INSTRUCTIONS
TO AVOID A SHORT CIRCUIT
PLEASE INSERT THE END OF THE CAMERA
CABLE COMPLETELY INTO THE CABLE
BUSHING WITHOUT FAIL.
CORRECT WRONG
The camera cable
is COMPLETELY
inserted
Fastening screws
Screws
Washer
Camera
Fastening cylinder
Digital door viewer
The camera cable
is NOT inserted
COMPLETELY
Retaining
plate