BASI TS710 Quick reference guide

facebook.com/BASI GmbH @basi_gmbh www.basi.eu
ASSEMBLY/OPERATING INSTRUCTIONS
For house entrance and apartment doors
Generous display
Wide-angle lens
Digital Door Viewer
TS 710

Intended use
Read the usage and maintenance in-
structions carefully before mounting the
spyhole. Keep the manual with you for
future use. If the product is passed on to
any third party, include the manual withit.
Warnings: There should be no dangers
whatsoever expected in the pro-
fessional assembly and operation
compliant with the instructions.
Small parts and packaging mate-
rials can be swallowed by children
and lead to choking! Make sure that small
parts and packaging materials do not get
into the hands of children. Dispose of the
packaging material immediately.
Please read these operating instructions
before using the device. The camera or
main body MUST NOT be dismantled.
Please handle the device carefully. In or-
der to prepare for the assembly, please
loosen the two screws on the lower side
of the viewer, take out the retaining plate
and remove the protective film.
The manufacturer expressly reserves the
right to make technical changes.
Disclaimer
The manufacturer accepts no liability for
damage or injury resulting from incorrect
handling.
Disposal
Help to protect the environment
and dispose of the product and the
packaging materials in accordance with
the local regulations. Do not dispose of
the device in household waste! Electronic
devices must be disposed of in accord-
ance with the directive on waste electri-
cal and electronic equipment via the lo-
cal collection points for waste electronic
equipment!
BEFORE THE ASSEMBLY:
Please put in the battery first before you
install the door viewer.
1. Slide the cover left to open.
2. Install the batteries in accordance with
the +/- sign.
3. Close the cover.
Assembly:
Step 1:
Remove the retaining plate of the digital
door viewer by loosening the lower fas-
tening screw (2).
Step 2:
Remove existing viewer or drill a 14 mm
wide hole in the door at eye level. Put in
the camera form outside and simultane-
ously place the washers between back of
the lens and the door. Make sure that the
arrow at the front of the camera points
upwards.
Step 3:
Now route the camera’s connection ca-
ble withe the plug on the inside of the
door through the retaining plate. Place
the retaining plate over the end of the
camera lens and then screw the fasten-
ing cylinder on the camera threads; this
will fasten the place on the door.
Step 4:
The camera’s connecting wire should
now be properly connected at the
General notes

bushing at the back of the door
viewer; excess wire should be fas-
tened behind the small hook.
Step 5:
Hook the digital door viewer in the
clamp above on the retaining plate (ar-
row upwards) and fasten the viewer by
inserting the two small screws through
the opening below on the housing of
the viewer and tighten the screws.
Operation:
1.Switch on/off button: Press and release
the button; the device is then activated
for 10 seconds.
2.Display lamp: If the display lamp lights
up, please replace the batteries.
Technical specifications
For house and apartment front doors
Suitable for doors with a door thickness of 38 - 110 mm
Installation diameter: 14 - 22 mm
Screen 3.5” thin-film transistor Sensor 0.3 megapixel CMOS
Batteries 2 AAA batteries Wide-angle lens 105°
Product size 125 mm (width) x 68 mm (height) x 15 mm (depth)
Door
1
2
1
2
Tür
Hängen
Schraube
Switch On/
Off button

© Copyright
Reprint or copy (even in excerpts) may
be made only with the permission of:
BASI GmbH
Konstantinstrasse 387
41238 Mönchengladbach
Germany
2023
This publication, including all its parts, is
protected by copyright.
Any use outside the strict limits of
copyright without the consent of BASI
GmbH is not permitted and punishable.
This applies in particular to duplications,
translations, microfilming and the
feeding and processing in electronic
systems.
WARNING!
Make sure you assemble the door bell
camera carefully. Do not pull or fold the
camera wire. If the camera wire is pulled
or folded, this could damage the product.
When fitting the door viewer camera, first
unscrew the camera cylinder and insert
the door viewer camera into the pee-
phole with the arrow points up. After the
camera ist well positioned, screw up the
locking cylinder from inside door. Do not
rotate the camera from out side door,
this could damage the camera. Also
do not rotate camera when disassem-
bling this product.
Fastening screw
Digital door viewer
②
①
Retaining plate
③
Washer
Camera
⑤
④
Befestigungszylinder
⑥
⑦
Befestigungswerkzeug
Scope of delivery:
1) Digital door viewer
2) Fastening screw
3) Retaining plate
4) Camera
5) Washer
6) Fastening cylinder
7) Fastening tool
Not in the scope of delivery:
2 AAA batteries
Don‘t pull or fold
the camera wire