Bassett Inspired BP-ALDH56-W9 User manual

Item# BP-ALDH56-W9
ADELINE WRITING DESK & HUTCH
ASSEMBLY INSTRUCTIONS
IF PARTS ARE MISSING OR DAMAGED, DO NOT RETURN TO STORE
To order missing or replacement parts, contact us via e-mail parts@officestar.net, by Fax [phone], or toll free parts
number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00 p.m. Pacific Time.

LIMITED WarranTy
INSPIRED by Bassett®Warrants, to the original purchaser its products to be free from defects in material and workmanship for a period of
5 years. Defects and damage from misuse, abuse, negligence, alteration, accident, vandalism, rusting, acts of nature or any other event
beyond the control of INSPIRED by Bassett®is not covered. The warranty does not cover cosmetic damage that may result from normal
use. Liability for incidental or consequential damages is excluded. The user assumes all risk of injury resulting from use of this product. This
warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
To make a warranty claim, contact Customer Service, provide model number, sales receipt and description of the problem. It is the
customer’s responsibility to prepay freight on any components returned to the factory. INSPIRED by Bassett®will pay return freight on
components covered under terms of warranty.
WarnInG
1. Do not use this product unless all screws and bolts are securely tightened.
2. Check that all screws and bolts are tight every three months or as needed.
3. Dispose of packing material properly. Do not use plastic cover as head covering. It may cause suffocation.
4. Do not use this product as a stepladder.
5. Use this product for its intended purpose only.
6. Intended for residential use only.
Contact us via e-mail parts@officestar.net, by Fax [phone], or toll free parts number 1-800-950-7262, Monday through
Friday 8:00 a.m. - 5:00 p.m. Pacific Time.
36.3 kg (80 lb.)
90.7 kg (200 lb.)
18.1 kg (40 lb.)

PARTS LIST
PictureLabel Description Qty
A
B
C
Hutch Top Panel
Hutch Top Rail
Hutch Left Side Panel
1
1
1
DHutch Left Middle Panel 1
EHutch Left Dividers 2
FHutch Left Bottom Panel 1
GHutch Left Back Panel 1
HHutch Right Side Panel 1
IHutch Right Middle Panel 1
JHutch Right Divider 1

PARTS LIST
PictureLabel Description Qty
K
L
M
Hutch Right Upper Shelf
Hutch Right Lower Shelf
1
1
N
Hutch Right Bottom Panel 1
O
Hutch Right Back Panel 1
P
Charging Station 1
Q
Desk Top 1
R
Desk Left Side Frame 1
S
Desk Right Side Frame 1
Desk Shelf 1

THANK YOU for purchasing this quality product. Be sure to check all packing material carefully for small parts which may have come loose
inside the carton during shipment. Identify and count all parts and compare with the parts and hardware lists.
Contact us via e-mail parts@officestar.net, by Fax [phone], or toll free parts number 1-800-950-7262, Monday through
Friday 8:00 a.m. - 5:00 p.m. Pacific Time.
HARDWARE LIST
Label Description QyPicture
H-1
H-2 Cam Lock
Cam Bolt
Wooden Dowel
11 + 2 EXTRA
H-3
Size
H-4 Bolt
H-5 Bolt
T-2 Wrench 1
08 x 30 mm
5/16’’ x 1/2’’
5/16’’ x 1-1/4’’
4 mm
Flat Washer 5/16’’
Metal Plate
H-7
H-10
T-1 Wrench 1
11 + 2 EXTRA
46 + 4 EXTRA
4 + 1 EXTRA
20 + 2 EXTRA
20 + 2 EXTRA
2
H-6 Flat Washer 5/16’’ x 1/2’’ 20 + 2 EXTRA
Lock Washer 1/4’’
H-8 20 + 2 EXTRA
Lock Washer 5/16’’
H-9 20 + 2 EXTRA
T-3 Wrench 1
5 mm

H-3
H-5
H-6
H-7
T-2
C
D
E
C
D
E
F
H-3
C
D
E
H-6 H-7H-5
STEP 1:
Insert two Wooden Dowels (H-3) into edges of Hutch Left Side Panel (C), Hutch Left Middle Panel (D) and
both Hutch Left Dividers (E).
STEP 2:
Attach Hutch Left Bottom Panel (F) to panels (C, E & D) and secure using four Flat Washers (H-6), four
Lock Washers (H-7) and four Bolts (H-5). FULLY TIGHTEN ALL BOLTS (H-5) USING WRENCH (T-2).

H-3
H
I
J
K
L
H-3
J
K
H-3
H-3
STEP 3:
Insert two Wooden Dowels (H-3) into edge of Hutch Right Divider (J), attach Hutch Right Upper Shelf (K) to Hutch Right Divider (J).
STEP 4:
Insert two Wooden Dowels (H-3) into both edges of Hutch Right Upper Shelf (K) and Hutch Right Lower Shelf (L), attach Hutch Right Middle
Panel (I) and Hutch Right Side Panel (H) to panels (K & L).

H-1
H-3
H-6
H-7
H-5
T-2
G
M
N
H-5 H-6 H-7
H-1
STEP 5:
Insert four Wooden Dowels (H-3) into bottom of Hutch Right Bottom Panel (M) and secure to
assembly using four Flat Washers (H-6), four Lock Washers (H-7) and four Bolts (H-5).
FULLY TIGHTEN ALL BOLTS (H-5) USING WRENCH (T-2).
STEP 6:
Slide Hutch Left Back Panel (G) into grooves of panels (C & D). Slide Hutch Right Back Panel (N) into grooves of panels (I & H)
Insert one Cam Bolt (H-1) into Hutch Left Side Panel (C) and Hutch Right Side Panel (H).

H-1
H-2
H-3
A
B
H-1
H-3
H-2
T-1
STEP 7:
Insert one Wooden Dowel (H-3) into panels (C & H). Attach Hutch Top Rail (B) and secure using two
Cam Locks (H-2). FULLY TIGHTEN CAM LOCKS (H-2) USING WRENCH (T-1).
STEP 8:
Insert ten Cam Boots (H-1) into bottom of Hutch Top Panel (A). FULLY TIGHTEN CAM LOCKS (H-2) USING WRENCH (T-1).

H-2
H-3
T-1
A
H-3
H-2
STEP 9:
Insert fourteen Wooden Dowels (H-3) into top of hutch assemblies.
STEP 10:
Attach Hutch Top Panel (A) to hutch assembly and secure using ten Cam Locks (H-2). FULLY TIGHTEN CAM LOCKS (H-2) USING
WRENCH (T-1).

H-3
H-6
H-7 H-5
T-2
P
Q
R
S
H-3 H-5 H-6 H-7
STEP 11:
Insert two Wooden Dowels (H-3) onto both ends of Desk Top (P) and Desk Shelf (S). Attach Desk Right Side Frame (R) and Desk Left Side
Frame (Q) and secure using four Flat Washers (H-9), four Lock Washers (H-7) and four Bolts (H-5). DO NOT FULLY TIGHTEN
BOLTS (H-5). Secure Desk Shelf (S) between Desk Right Side Frame (R) and Desk Left Side Frame (Q) using four Flat Washers (H-9), four Lock
Washers (H-7) and four Bolts (H-5). FULLY TIGHTEN ALL BOLTS (H-5) USING WRENCH (T-2).
STEP 12:
Carefully place hutch assembly onto desk assembly.

H-4 H-8
T-2
O
H-8
H-4
STEP 13:
Secure hutch assembly to desk assembly using two Metal Plates (H-8). Secure each Metal Plate (H-8) using two Flat Washers (H-6), two Lock
Washers (H-8) and two Bolts (H-4) for each Metal Plate (H-8). FULLY TIGHTEN BOLTS (H-4) USING WRENCH (T-2).
STEP 14:
Slide Charging Station (O) into hutch assembly.

FUrnITUrE CarE:
- Dust with a soft cloth following the grain pattern of the wood.
- Dust often to remove the everyday abrasive particles from the wood surfaces.
- Before dusting, moisten cloth lightly with a spray product.
- Wood finishes also benefit from an occasional polishing.
Contact us via e-mail parts@officestar.net, by Fax [phone], or toll free parts number 1-800-950-7262, Monday through
Friday 8:00 a.m. - 5:00 p.m. Pacific Time.