Bassett INSPIRED BARCELONA BP-BARCSL2 User manual

IF PARTS ARE MISSING OR DAMAGED, DO NOT RETURN TO STORE
To order missing or replacement parts, contact us via e-mail parts@officestar.net, by Fax [phone], or toll free parts
number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00 p.m. Pacific Time.
Item# BP-BARCSL2
BARCELONA 2 DOOR CONSOLE
ASSEMBLY INSTRUCTIONS

LIMITED WARRANTY
INSPIRED by Bassett®Warrants, to the original purchaser its products to be free from defects in material and workmanship for a period of
5 years. Defects and damage from misuse, abuse, negligence, alteration, accident, vandalism, rusting, acts of nature or any other event
beyond the control of INSPIRED by Bassett®is not covered. The warranty does not cover cosmetic damage that may result from normal
use. Liability for incidental or consequential damages is excluded. The user assumes all risk of injury resulting from use of this product. This
warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
To make a warranty claim, contact Customer Service, provide model number, sales receipt and description of the problem. It is the
customer’s responsibility to prepay freight on any components returned to the factory. INSPIRED by Bassett®will pay return freight on
components covered under terms of warranty.
WARNING
1. Do not use this product unless all screws and bolts are securely tightened.
2. Check that all screws and bolts are tight every three months or as needed.
3. Dispose of packing material properly. Do not use plastic cover as head covering. It may cause suffocation.
4. Do not use this product as a stepladder.
5. Use this product for its intended purpose only.
6. Intended for residential use only.
Contact us via e-mail parts@officestar.net, by Fax [phone], or toll free parts number 1-800-950-7262, Monday through
Friday 8:00 a.m. - 5:00 p.m. Pacific Time.
November, 2017
FURNITURE CARE:
- Dust with a soft cloth following the grain pattern of the wood.
- Dust often to remove the everyday abrasive particles from the wood surfaces.
- Before dusting, moisten cloth lightly with a spray product.
- Wood finishes also benefit from an occasional polishing.
THANK YOU for purchasing this quality product. Be sure to check all packing material carefully for small parts which may have come
loose inside the carton during shipment. Identify and count all parts and compare with the parts and hardware lists.

PARTS LIST
(2) Bottom Frame (1 PC)
(1) Top Frame (1 PC)
(4) Right Side Frame (1 PC)
(3) Left Side Frame (1 PC)
(6) Left Door (1 PC)
(5) Back Panel (1 PC)
(8) Shelf (1 PC)
(7) Right Door (1 PC)

HARDWARE LIST
DRAWINGNO DESCRIPTION SIZE
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
QTY.
8 PCS
1/4” x 1/2” 1 PCSmall Bolt
1/4” x 2/5” 1 PCConnector Bolt
1/8” x 1” 2 PCSLarge Screw
Medium Flat Washer
Large Flat Washer
1/4” x 2/5” x 0.08”Lock Washer
4 PCS1/4” x 2/5”Nut
4 PCSn / aShelf Pin
2 PCSn / aHandle
1 PCn / aAnti-Tip Kit
2/5” x 4/5” x 0.08” 1 PC
8 PCS1/4” x 5/8” x 0.08”
1/4” x 2” 8 PCSLong Bolt
1/8” 5/8” 4 PCSSmall Screw
4 PCS1/4” x 1/2” x 0.08”Small Flat Washer
n / a 1 PC
2 PCS
Back Lid
2/5” 1 PCSocket Wrench
n / a 1 PCTriangle
1/8”Allen Wrench

STEP 1:
STEP 2:
(2)
(5)
(N)
(O)
(O)
(A)
(C)(H)
(3)
(O)
(B)
(I)
(G)
(1)
Attach Top Frame (1) and Bottom Frame (2) to Left Side Frame (3) using two Long Bolts (B), two Lock Washers (I) and two
Flat Washers (G) for each frame. DO NOT FULLY TIGHTEN BOLTS.
Attach Back Lid (N) to Back Panel (5) using one Small Bolt (A), one Flat Washer (H) and one Connector Bolt (C).
FULLY TIGHTEN ALL BOLTS.

STEP 3:
STEP 4:
(2)
(2)
(5)
(5)
(5)
(Q)
(O)
(E)
(D)
(4)
(3)
(3)
(B)
(I)
(G)
(1)
(1)
Slide Back Panel (5) into groove of Top Frame (1) and Bottom Frame (2).
Secure Right Side Frame (4) to console using four Long Bolts (B), four Lock Washers (I) and four Flat Washers (G). Line up Back
Panel (5) using Triangle (Q).Secure Back Panel (5) to assembled console using two Large Screws (E) and four Small Screws (D).
FULLY TIGHTEN ALL SCREWS AND BOLTS.

STEP 5:
STEP 6:
(F)(J)
(P)
(F)(J)
(P)
(6)
(6)
(7)
(7) (7)
(1)
(3)
(4)
(4)
(L)
Attach Handles (L) to Doors (6 & 7) using two Flat Washers (F) and two Nuts (J) for each handle. FULLY TIGHTEN ALL NUTS.
Attach Doors (6 & 7) to assembled console.

STEP 7:
STEP 8:
(8)
(K)
(M)
(5)
(1)
(1)
(3)
(4)
(4)
Insert Shelf Pins (K) into assembled console. Slide Shelf (8) into assembled console.
Place Console (1) in desired location. Attach two brackets to back of Console (1) using two short screws for each bracket.
FULLY TIGHTEN SCREWS. Attach the remaining brackets to wall using two long screws for each bracket. FULLY TIGHTEN SCREWS.
Loop one safety strap between each set of brackets and fasten safety straps.