Bauco bauco-plus II User manual

CALL TOLL FREE
1-877-592-0033
(250-592-0033)
23
Email: [email protected]
Web: www.accesspanelsolutions.com
18
Installation Instructions
bauco-plus II TM
Introduction and Key Concepts
Installation Methods
Access Panel Outer Frame
The dimensions of the Clear Opening in the frame are used to
determine the Cut Opening (opening in drywall) and the
minimum Rough Frame Opening (spacing of framing
members).
The number group following the rst 4 digits in the
model number is the clear opening dimensions.
Ex: access panel with the Model Number
20-58-1212 has a 12” x 12” clear opening.
The outer frame mounts to the back of the drywall
and is attached with self-drilling drywall screws
through the face of the drywall.
Standard Installation
The framing members must be positioned correctly around the opening in the
drywall for the access panel. Drywall is attached to the studs as usual but
overlaps to create a lip to acceps the access panel outer frame. The cut
opening required for the access panel is cut and the frame angled
through the opening and attached according to the information on
the next page. Alternative methods for locating outer frame are
outlined on next page.
Ex: For a Model Number 20-58-1212 with a 12” x 12” clear
opening, the minimum spacing of the framing is 14 1/2” with 1 1/4”
on either side of the opening. The maximum spacing is 20” with 4”
maximum on either side of the opening. The distance to the studs
does not have to be the same as long as the framing is within the
maximum and minimum dimensions.
Size of the Cut Opening (B)
Door Size (A) number group following rst 4 digits in the model number.
The Cut Opening (B) is the Door Size (A) + 3/8” (drywall opening size).
Size of the Minimum Rough Framed Opening (C)
The minimum distance from the framing to a stud is 1 1/4”. The maximum is 4”
Access Panel Door Leaf
The door leaf is opened by pressing on
the panel on the latch side.
When released, the panel
springs open.
For trouble-free installation and operation,
please observe the following:
| The access panel outer frame must be screwed to the drywall every 4” or less with more precise attachment
at the corners and through the base of all latch brackets.
| The outer frame must be attached to the drywall square and straight. Frame is exible; attach straight.
| The wall or ceiling must be rigid. Blocking and/or rigid hangers must ensure no exibility or movement in drywall.
| The drywall surrounding the outer frame should be at. If screw heads protrude above the face of the framing, it is
recommended that drywall shims are used to make a at surface.

CALL TOLL FREE
1-877-592-0033
(250-592-0033)
24
Email: [email protected]
Web: www.accesspanelsolutions.com
Stud Anchors (Included with large panels, otherwise upon request)
The panel outer frame can be hung in the rough framed opening before the drywall is in
place by using the Stud Anchors. Stud Anchors clip into the outer frame and are screwed or tied
to the framework. After drywall is tted around the frame, the frame must be attached as
shown in the next section.
Stud anchors are and
installation aid
only.
Pass the frame through the opening into position (or locate with alternative
method) so outer frame rests on back of drywall. Ensure the frame is
straight and square. Screw through the drywall into the frame of the
access panel. Correct fastener spacing must be followed.
Insert door leaf and test function. Remove. Apply ller into any gaps around the outer frame, lling to the level of the raised edge. Apply
ller to the door leaf. Sand and ll until desired nish is achieved. Finished height must not be higher than edge of outer frame and
door leaf frame. Setting-type compound is recommended for the rst coat. Clean excess ller and dust from frame with a damp cloth.
During Drywall Installation
The access panel outer frame can
be located resting on the back of
the drywall as the drywall is being
installed. If possible, avoid putting
joints at the corners.
The frame must be
attached as show
in the next section.
Installation Instructions
bauco-plus II TM
Alternative Installation Methods
Outer Frame Installation and Panel Finishing
* *
Recommended screw
Recommended screw
1 1/4” (32 mm) screw
Safety cap
Important Fastener Placement
At the latch side only, a screw should be ttedin line with
the edge of the frame. It will go through the steel corner
brackets. If multiple latches, place fasteners through the base
of all latch brackets.
Use extra screws on
latch side.
Prime and paint together or
separately. Attach the
safety cable when
complete.
*