Baudcom FC-7S User manual

○Please read the instruction manual carefully before operation,
keep instruction manual and fiber cleaver in a good place at the
same time.
○In order to prevent the damage of the machine performance ,
please note the following when you use fiber cleaver.
○Don’t get wet fiber cleaver.
○Don’t put the fiber cleaver in a place where is wet or dusty.
○Under normal temperature preservation in order to avoid high
temperature cause deformation.○Don't hit so hard fiber cleaver.
○Leave about 12 mm long bare fiber.
○Regularly clean up dirt on pressure fiberboard with alcohol,
don't use acetone or corrosive solvent cleaning pressure fiberboard.
○Constantly clean up fiber box and ensure no dust and oil dirties
in the slot.
FC-7S High precision fiber cleaver instruction manual
Method of use and regulation of safety operation.
Product model
Fiber cleaver
optical fiber cladding
diameter
125μm
Fiber coating diameter
0.25mm-0.9mm
Coated outer diameter
Single core
The length required to be
removed before optical
fiber cutting
Fiber cutting length ≥18mm
Fiber cutting length
5-20mm
Fiber cutting angle
≤0.8°
Blade life
48000（1000timesx16
positionx3high）
Size
63Wx65Dx60H(mm)
Weight
280g(coffee color)/180(black
color)
Fxture
Three in one multifunction jip
Operating steps
1.Open the pressure fiberboard
and cover plate, put bare fiber
in the fixture that was stripped
coating（125mm/900mm）,
according to user’s
requirement to ensure
cutting length.
2.Push to the front of
the cutting slider(Figure),
press and close the
pressure fiberboard and
cover plate to fix optical
fiber.
3.After close cover plate,
ensure that the fiber
is in a horizontal line.
4.Push cutting slider
back a one-time to
finish cutting.
5.Open cover plate
and pressure fiberboard,
then take out the fiber. In
order to avoid damaging
the fiber, fiber face don’t
touch anything after take
it out.
6. After finish cutting, please clean up the broken fiber and
don’t damage blade for later use.
Fixed optical fiber mat
Blade
Cleaver body
Pressure fiberboard
Single optical
Fiber fixture
Block
Cover plate
Cleaver push
block
Fixed optical fiber mat

Blade’s replacement and adjustment
☉0-15 cutting points are indicated on the blade.
☉Please clean up blade and fiber fixture when the cleaver cannot be used properly(Do not wipe fixed optical fiber mat with
alcohol).
☉If it still doesn’t work, please adjust the position of the blade.
Please according to the following operation sequence when you adjust the position of the blade.
A. Adjust the blade（According to the maked on the blade 0-15 face to turn）
1. Provide "一" type screwdriver for yourself.
2. First, loose the screw on the blade with "一" type screwdriver(Figure) and adjust
the position of blade. Turn one face every time and fix blade. If it still doesn’t work,
the following steps need to adjust blade and the height of the cutting slider.
B. Adjust blade height
1. The blade below the two
hexagonal screws are loosen by
hex wrenches.(Figure)
2．Slightly adjust the screw
right as shown. Clockwise
to lift the blade, and vice in
order to lower the blade
height.
3.Open pressure fiberboard and cover plate, put bare fiber in the fixture that
was stripped coating（125mm/900mm）,press and close pressure fiberboard,
push cutting block back and forth, then you can see the fiber cleaver’s blade
whether just meet fiber or not ,if not, please repeat step 2.
Lift blade, if meet too much, please repeat step 2 to lower blade. Adjust the
best position, then tighten two hexagonal screws that’s loosen in the first
step with hex wrenches.
C. Replace new blade
1. Remove the old blade, install the new blade..
2. According to “Adjust blade height” to adjust
blade’s high or low.
Attention：please don’t adjust cleaver with inappropriate “一” type screwdriver or hex wrenches.
D.Optional accessory
standard
optional
optional
Attention：please don’t adjust cleaver with inappropriate “一” type screwdriver or hex wrenches.
Anything, please feel free to contact with us:
www.baudcom.com.cn
[e-mail]
tel: [phone]