Baumatic BDFF 612 User manual

INSTRUCTION MANUAL
BDFF 612
Free Standing
Dishwasher

2
CONTENTS
General safety rules
Installation
Water connection
Loading the salt
Adjusting the upper basket
Loading the dishes
Information for test laboratories
Loading the detergent
Types of detergent
Loading the rinse aid
Cleaning the filters
Some practical hints
Routine cleaning and maintenance
Description of the control panel
Technical data
Programme selection and special functions
Programme guide
Water softner unit
Identifying minor faults
Product fiche
WEEE information
Contact details
Please read the instructions in this booklet carefully because they contain important
information on how to install, use and maintain your dishwasher safely as well as
containing useful tips on how to make the most of it.
Keep this booklet safe for future reference.
pag. 3
pag. 5
pag. 6
pag. 8
pag. 9
pag. 10
pag. 12
pag. 13
pag. 14
pag. 15
pag. 16
pag. 17
pag. 18
pag. 19
pag. 19
pag. 20
pag. 24
pag. 26
pag. 27
pag. 29
pag. 30
pag. 31
Fig. A
32
1
4
5

3
GENERAL SAFETY RULES
■This appliances is intended to be
used in household and similar
applications such as:
- staff kitchen areas in shops,
offices and other working
environments;
- farm houses;
- by clients in hotels, motels
and other residential type
environments;
- bed and breakfast type
environments.
A different use of this appliance
from household environment or
from typical housekeeping
functions, as commercial use by
expert or trained users, is
excluded even in the above
applications.
If the appliance is used in a
manner inconsistent with this
it may reduce the life of the
appliance and may void the
manufacturer’s warranty.
Any damage to the appliance or
other damage or loss arising
through use that is not consistent
with domestic or household use
(even if located in a domestic or
household environment) shall not
be accepted by the manufacturer
to the fullest extent permitted by
law.
■This appliance can be used by
children aged from 8 years and
above and persons with reduced
physical, sensory or mental
capabilities or lack of experience
and knowledge if they have been
given supervision or instruction
concerning use of the appliance in
a safe way and understand the
hazards involved.
Children shall not play with the
appliance. Cleaning and user
maintenance shall not be made
by children without supervision.
■Children should be supervised to
ensure that they do not play with
the appliance.
■Children of less than 3 years
should be kept away unless
continuously supervised.
■Should it be necessary to replace
the supply cord, call the Customer
Care Department.
■The appliance must be connected
to the water mains using new
hose-sets. The old hose-sets
should not be reused.
■Water pressure must be between
0,08 MPa and 0,8 MPa.
■When the appliance is located on
a carpet floor, attention must be
paid to ensure that there is no
obstruction to the bottom vents.
■After installation, the appliance
must be positioned so that the
plug is accessible.

4
■For the maximum place loading,
please refer to the "TECHNICAL
DATA" table/section.
WARNING !
Knives and other utensils with
sharp points must be loaded
in the basket with their points
down or placed in a horizontal
position.
■The door should not be left in the
open position since this could
present a potential hazard ( e.g.
tripping ).
■To consult the product fiche
please refer to the relevant page
in this user manual.
Safety instructions
■Make sure the electrical system
is grounded. Otherwise, seek
qualified professional assistance.
Manufacturer declines all
responsibility for any damage
due to non-earthing of the
machine.
■Ensure that the dishwasher does
not crush power cables.
■In general it is not advisable to use
adaptors, multiple plugs and/or
extension cables.
■Do not remove the plug from the
mains supply socket by pulling the
mains cable or the machine itself.
■Do not leave the appliance expo-
sed to the elements (rain, sun etc).
■Leaning or sitting on the open
door of the dishwasher could
cause it to tip over.
■The dishwasher is designed for
normal kitchen utensils.
Objects that have been contami-
ned by petrol, paint, traces of steel
or iron, corrosive chemicals, acids
or alkalis must not be washed in
the dishwasher.
■If there is a water softening device
installed in the home there is no
need to add salt to the water sof-
tener fitted in the dishwasher.
■If the appliance breaks down or
stops working properly, switch it
off, turn off the water supply and
do not tamper with it. Repair work
should only be carried out by an
approved service agent and only
genuine spare parts should be fit-
ted.Any failure to follow the above
advice may have serious conse-
quences for the safety of the
appliance.

5
7
598 556/573
5
INSTALLATION IN FITTED
KITCHENS
Fitting between existing cabinets
■The height of the dishwasher, 85 cm, has
been designed in order to allow the
machine to be fitted between existing
cabinets of the same height in modern
fitted kitchens. The feet can be adjusted
so that correct height is reached.
■The laminated top of the machine does
not require any particular care since it is
heatproof, scratchproof and stainproof
(fig. 5).
Underneath existing work top
(when fitting beneath a work top)
■In most modern fitted kitchens there is
only one single work top under which
cabinets and electrical appliances are
fitted. In this case remove the work top
of the dishwasher by unscrewing the
screws under the rear edge of the top
(fig. 6a).
IMPORTANT
After removing the work top, the
screws MUST BE screwed again
under the rear edge of the top
(fig. 6b).
■The height will then be reduced to 82 cm,
as scheduled by the International
Regulations (ISO) and the dishwasher
will fit perfectly under the kitchen
working top (fig. 7).
6a
ba
b
■If it you need to move the machi-
ne after removing the packaging,
do not try to lift it by the bottom of
the door.
Open the door slightly and lift the
machine by holding on the top.
■For the installation of built-in
appliances, please refer to the
specific chapter or to the instruc-
tions enclosed with the booklet.
Appliance complies with
European Directives:
■2006/95/EC (LVD);
■2004/108/EC (EMC);
■2009/125/EC (ErP);
■2011/65/EU (RoHS)
and subsequent amendments

6
WATER CONNECTION
IMPORTANT
The appliance must be connected to
the water mains using new hose-sets.
The old hose-sets should not be reused.
■The inlet and drain hoses can be directed
to left or right.
IMPORTANT
The dishwasher can be connected to
either cold or hot water, as long as it
is no hotter than 60°C.
■Water pressure must be between
0,08 MPa and 0,8 MPa.
■The inlet hose must be connected to a
tap so that the water supply can be cut
off when the machine is not in use
(fig. 1 B).
■The dishwasher is fitted with 3/4" threaded
connector (fig. 2).
■Connect inlet hose “A” to water tap “B”
with a 3/4" attachment making sure that
it has been properly tightened.
■If it is necessary, the inlet pipe can be
lengthened up to 2,5 m. The extension
pipe is available from the Spares
Department.
■If the dishwasher is connected to new
pipes or to pipes which have not been in
use for a long time run water through for
a few minutes before connecting the
inlet hose. In this way no deposits of
sand or rust will clog up the water inflow
filter.
1
2

7
Connecting the outlet hose
■The outlet hose should disharge into a
standpipe, making sure that there are no
kinks (fig. 4).
■The standpipe must be at least 40 cm
above floor level and it must have an
internal diameter of at least 4 cm.
■It is advisable to fit an anti-odour air trap
(fig. 4X).
■If necessary the outlet hose can be
extended up to 2,5 m, provided that it is
kept at a maximum height of 85 cm
above floor level. The extension pipe is
available from the Spares Department.
■The hose can be hooked over the side of
the sink, but it must not be immersed in
water, in order to prevent water from
being syphoned back to the machine
when this is in operation (fig. 4Y).
■When installing the appliance under a
worktop the hose pipe clamp must be
attached to the wall in the highest possible
position under the worktop (fig. 4Z).
■Check that there are no kinks in the inlet
and outlet hoses.
4

8
LOADING THE SALT
■The appearance of white stains on dishes
is generally a warning sign that the salt
container needs filling.
■On the bottom of the machine there is a
container for the salt for regenerating
the softener.
■It is important to use only a salt that is
specifically designed for dishwasher.
Other types of salt contain small quantities
of insoluble particles which over a long
period of time may affect and deteriorate
the softener performance.
■To add salt, unscrew the cap of the con-
tainer on the bottom and then refill the
container.
■During this operation a little water will
overflow; but keep adding salt until the
container is full. When the container is
full, clean the thread of salt residue and
retighten the tap.
■After filling with salt, it is recommended to
run a complete wash cycle, or COLD
RINSE programme to clear any residual
salt from the inside of the cabinet.
IMPORTANT
After loading the salt, YOU
MUST run a complete washing
cycle, or the PRE-WASH/COLD
RINSE/REFRESH programme.
■The salt dispenser has a capacity of
between 1.5 and 1.8 kg and, for efficient
use of the appliance, it should be refilled
from time to time according to the
regulation of the water softener unit.
IMPORTANT
(Only for first start up)
When the appliance is used for the
first time, after completely filling the
salt container, it is necessary to add
water until the container overflows.

9
ADJUSTMENT OF THE UPPER
BASKET
If 29 cm to 32.5 cm plates are normally
used, load them onto the lower basket after
the upper basket has been placed in its
upper position and proceed as detailed
below:
1. Turn the front stops “A” outwards;
2. Take out the basket and remount it in the
upper position;
3. Replace the blocks “A” in their original
position.
Dishes that are bigger than 20 cm in
diameter can no longer be loaded onto the
upper basket and the mobile supports
cannot be used when the basket is in the
upper position.
A
A

10
LOADING DISHES
Using the upper basket
■The upper basket is provided with
mobile racks hooked to the sides of the
basket, which can be regulated into 4
positions.
■In the lowered position (A-A1) the racks
may be used for such items as: tea and
coffee cups, kitchen knives and ladles.
Also glasses with stems may be safely
hung on the ends of the racks.
■In the upright position (B-B1) the racks
allow you to load dinner plates and soup
plates. Plates should be loaded
vertically with the underside of the plate
towards the back of the dishwasher with
a space between each plate to allow
water to pass freely.
■It is advisable to load large plates
(approx. 26 or more cm) slightly tilted
towards the rear to facilitate introduction
of the basket into the machine.
■Salad bowls and plastic bowls may also
be loaded on the upper basket. It is
advisable to block these in place so that
the jets of water do not make them
overturn.
■The upper basket has been designed to
offer maximum flexibility in use and can
be loaded with up to 24 plates on two
rows, up to 30 glasses on five rows or a
mixed load.
BB1
AA1
A standard daily load is represented in
figs. 1, 2 and 3.
Upper basket (fig. 1)
A= soup plates
B= dinner plates
C= dessert plates
D= saucers
E= cups
F= glasses
Upper basket (fig. 2)
A= soup plates
B= dinner plates
C= dessert plates
D= saucers
E= cups
F= glasses
G= single section cutlery basket
AB
C
D
E
F
ABCD
E
1
2
FG
F

11
Upper basket (fig. 3)
A= glasses
B= saucers
C= cups
D= small bowl
E= medium bowl
F= large bowl
G= serving spoons
Using the lower basket
■Saucepans, oven dishes, tureens, salad
bowls, lids, serving dishes, dinner
plates, soup plates and ladles can be
loaded on the lower basket.
■Place the cutlery in the plastic cutlery
holder with the handles pointing
upwards.
■Place the cutlery holder in the lower
basket (fig. 4 and 5), making sure that
the cutlery does not get in the way of the
rotating arms.
IMPORTANT
The lower basket has a safety-stop
device, for its safe extraction, also
especially useful with a full load.
For loading salt, cleaning filter and for
ordinary maintenance, the complete
extraction of the basket is necessary.
Please load the dishwasher sensibly to
obtain the best wash results.
A standard daily load is represented in
figs. 4 and 5.
Lower basket (fig. 4)
A= medium-sized saucepan
B= large saucepan
C= frying pan
D= lids
E= tureens, serving dishes
F= cutlery
G= oven dishes
Lower basket (fig. 5)
A= soup plates
B= dinner plates
C= dessert plates
D= serving dish
E= cutlery
A
A
F
C
CB
E
D
G
G
3
C
A
A
EB
A
C
A
B
5
D
4
DFAG
E
BC

12
Cutlery basket (fig. 6)
The cutlery basket is made with two
detachable parts which will enable various
loading options.
The two parts can be detached by sliding
the left section away from the right section.
The top of cutlery basket can be removed,
for enable various loading options.
INFORMATION FOR THE TEST LABORATORIES
Please ask information required for comparison testing and measuring noise levels, according
to EN normative, to the following address:
[email protected]
In the request, please specify model name and number of the dishwasher (see rating plate).
6

LOADING THE DETERGENT
The detergent
IMPORTANT
It is essential to use a detergent
that is specifically designed for
dishwashers either in powder, liquid
or tablet form.
“FINISH” gives very good results and can
be easily obtained.
Unsuitable detergents (like those for
washing up by hand) do not contain the
proper ingredients for use in a dishwasher,
and stop the dishwasher from working
correctly.
Filling the detergent container
The detergent container is inside the door
(fig. A “2”). If the lid of the container is
closed, press the button (A) to open.
At the end of every wash cycle the lid is
always open and ready for the next time
the dishwasher is used.
WARNING!
When loading the lower basket, please
ensure that the plates or others do not
obstruct the detergent dispenser.
The amount of detergent to be used varies
according to how dirty the dishes are and
on the type of dishes to be washed.
We advise using 20:30 g of detergent in the
wash section of detergent compartment (B).
13
After pouring the detergent into the container,
close the lid, firstly pushing (1) and then
pressing on it (2) until you hear the click.
Since not all detergents are the same the
instructions on the boxes of detergent can
vary. We should just like to remind users
that too little detergent does not clean the
dishes properly whilst too much detergent
will not produce better results and is also a
waste.
IMPORTANT
Do not use an excessive amount of
detergent and help limit damage to
the environment at the same time.
A
B

14
TYPES OF DETERGENT
Detergent tablets
Detergent tablets of different manufacturers
dissolve at different speeds, for this
reason, during short programmes, some
detergent tablets may be not fully effective,
because they are not completely dissolved.
If these products are used, is recommended
to choose longer programmes to guarantee
the complete use of the detergent.
IMPORTANT
To get satisfactory washing results,
the tablets MUST be placed in the
wash section of the detergent
container and NOT directly in the
tub.
Concentrated detergents
The concentrated detergents, with reduced
alkalinity and with natural enzymes, in
conjunction with 50°C wash programmes,
have a smaller impact on the environment
and they protect the dishes and the
dishwasher.
The 50°C wash programmes purposely
exploit the dirt-dissolving properties of the
enzymes, allowing therefore, with the use
of the concentrated detergents, to achieve
the same results of the 65°C programmes
but at a lower temperature.
Combined detergents
The detergents that also contain the rinse
aid must be placed in the wash section of
the detergent container. The rinse aid
container must be empty (if it is not empty,
set the rinse aid regulator to lowest position
before using combined detergents).
"ALL in 1" combined detergents
If you are planning to use “ALL in 1” (“3 in 1 “/
“4 in 1”/ “5 in 1”, etc.) combined detergents i.e.
those with built in salt and/or rinse agent,
we would advise the following:
■Read carefully and follow the manufacturer’s
instructions given on the packaging;
■The effectiveness of detergents containing
the built in water softener/salt depends
on the hardness of your water supply.
Check that the hardness of your water
supply is within the effective range given
on the detergent packaging.
If when using this type of product, you
don't get satisfactory washing results,
please contact the detergent
manufacturer.
In certain circumstances use of combined
detergents can cause:
■limescale deposits on dishes or in the
dishwasher;
■a reduction in washing and drying
performance.
IMPORTANT
Any problems which arise as a direct
result of the use of these products
are not covered by our warranty.
Please note that using the "ALL in 1"
combined detergents, the rinse aid and
salt indicator lights (only used on
selected models) are superfluous, so you
must ignore the lights.
If washing and/or drying problems occur,
we recommend you return to use traditional
separate products (salt, detergent and
rinse agent). This will ensure that the water
softener in the dishwasher operates
correctly.
In this case, we recommends that you:
■refill both the salt and rinse aid container;
■run one normal washing cycle without a
load.
Please note that on return to the use of
conventional salt, a number of cycles will
be required before the system becomes
fully efficient again.

LOADING THE RINSE AID
The rinse aid
The rinse aid, which is automatically
released during the last rinsing cycle, helps
the dishes to dry quickly and prevents
spots and stains forming.
Filling the rinse aid container
The rinse aid container can be found to the
left of the detergent container (fig. A "3").
To open the lid, push the reference mark
and, in the same time, pull the tab of
opening.
It is always advisable to use rinse aid that
is specifically designed for dishwasher.
Check the rinse aid level through the
indicator eye (C) which is located on the
dispenser.
Regulating the rinse aid from 1 to 6
The regulator (D) is placed under the lid
and can be turned using a coin.
The recommended position is 4.
The limestone content of the water
considerably affects the formation of
limescale and the drying performance.
It is therefore important to regulate the
quantity of rinse aid to achieve good
washing results.
If, after the wash, streaks occur on the
dishes, decrease the amount by one
position. If whitish spots occur, increase the
amount by one position.
15
FULL EMPTY
dark light
C
D

16
1
2
3
CLEANING THE FILTERS
The filter system (fig.A “4”) consists of:
a central container that traps the larger
particles;
a flat gauze that continuously filters the
wash water;
a micro filter, located beneath the gauze,
that traps the tiniest particles ensuring a
perfect rinse.
■To achieve excellent results every time,
the filters should be checked and
cleaned after each wash.
■To remove the filter unit, simply turn the
handle anticlockwise (fig. 1).
■For ease of cleaning, the central container
is removable (fig. 2).
■Remove the gauze filter (fig.3) and
wash the whole unit under a jet of
water. If necessary a small brush can
be used.
■With the Self-cleaning Micro filter,
maintenance is reduced and the filter
unit need only be checked every two
weeks. Nevertheless, after each wash it
is advisable to check that the central
container and the gauze filter are not
clogged.
WARNING!
After cleaning the filters, make sure
that they are correctly reassembled
and that the gauze filter is properly
positioned at the bottom of the
dishwasher.
Make sure that the filter is screwed
back, clockwise, into the gauze, as
poor seating of the filter unit could
have an adverse effect on the
efficiency of the appliance.
IMPORTANT
Never use the dishwasher without
the filters.

17
PRATICAL HINTS
How to get really good wash
results
■Before placing the dishes in the
dishwasher, remove any remaining
food (bones, shells, pieces of meat or
vegetables, coffee grounds, skin of fruit,
cigarette ash, tooth picks etc. to avoid
blocking the filters, water outlet and
washing arm nozzles.
■Try not to rinse the dishes before
loading them into the dishwasher.
■If saucepans and oven dishes are
encrusted with the remains of burnt or
roast food, it is advisable to leave them
to soak before washing.
■Place the dishes face downwards.
■Try to place the dishes in such a way
that they are not touching one another.
If they are loaded properly you will get
better results.
■After loading the dishes check that the
washing arms can rotate freely.
■Pans and other dishes that have
particularly stubborn food particles or
remnants of burnt food should be left to
soak in water with dishwasher
detergent.
■To wash silver properly:
a) rinse the silver immediately after
use, especially if it has been used for
mayonnaise, eggs, fish etc.;
b) do not sprinkle detergent onto it;
c) keep it separate from other metals.
How to make savings
■If you want the dishwasher to give a
complete wash, place the dishes in the
dishwasher at the end of each meal and
if necessary turn on the COLD RINSE
cycle to soften the food remains and
remove bigger particles of food from the
new load of dishes.
When the dishwasher is full start the
complete wash cycle programme.
■If the dishes are not very dirty or if the
baskets are not very full select an
ECONOMY programme, following the
instructions in the program list.
What not to wash
■It should be remembered that not all
dishes are suitable for washing in a
dishwasher.We advise against using
the dishwasher to wash items in
thermoplastic, cutlery with wooden or
plastic handles, saucepans with
wooden handles, items in aluminium,
crystal, leaded glass unless otherwise
stated.
■Certain decorations may fade. It is
therefore a good idea before loading the
whole batch to wash just one of the
items first so as to be sure that others
like it will not fade.
■It is a good idea not to put silver cutlery
with non-stainless steel handles into
the dishwasher as there could be a
chemical reaction between them.
IMPORTANT
When buying new crockery or
cutlery always make sure that they are
suitable for washing in a dishwasher.
Useful hints
■In order to avoid any dripping from the
top rack, remove the lower rack first.
■If the dishes are to be left in the
machine for some time, leave the door
ajar, to let some air circulate and to
improve the drying performance.

18
WHEN CYCLE IS FINISHED
After every wash it is essential to turn off
water supply and to switch off the machine
by pressing the On/Off button to the off
position.
If the machine is not going to be used for
some time, it is advisable to follow these
rules:
1. do an empty wash with detergent in order
to clean the machine of any deposits;
2. pull out the electric plug;
3. turn off the water tap;
4. fill the rinse aid container;
5. Ieave the door ajar;
6. keep the inside of the machine clean;
7. If the machine is left in places where the
temperature is below 0°C any water left
inside the pipes may freeze. Wait until
the temperature rises above zero and
then wait for about 24 hours before
starting up the dishwasher.
CLEANING AND
MAINTENANCE
■To clean the dishwasher outside, do not
use solvents (degreasing action) neither
abrasives, but only a cloth soaked with
water.
■The dishwasher does not require special
maintenance, because the tank is
self-cleaning.
■Regularly wipe the door gasket with a
damp cloth to remove any food remains
or rinse aid.
■Dishwasher cleaning is recommended,
in order to remove limestone deposits or
dirt. We suggest you run a washing cycle
periodically with specialist dishwasher
cleaning products. For all cleaning
operations the dishwasher must be
empty.
■If, in spite of the routine cleaning of the
filters, you notice that the dishes or pans
are not properly washed or rinsed, check
that all the spray heads on the rotor
arms (fig. A “5”) are clear.
If they are blocked, clean them in the
following way:
1. to remove the upper rotor arm, turn it
until it lines up with the stop marked
by the arrow (fig. 1b). Push it upwards
(fig. 1) and, keeping it pushed in,
unscrew it in a clockwise direction
(to reassemble it repeat the same
operation, but turn it anticlockwise).
The lower rotor arm can be removed
simply by pulling it upwards (fig. 2);
2. wash the rotor arms under a jet of water
to clear any blockage in the spray
heads;
3. when you have finished, refit the rotor
arms in the same position, remembering
to re-align the arrow and screw into
position.
■Both the door lining and the tank lining
are in stainless steel; however, should
spots caused by oxidation occur, this is
probably due to a high level of iron salts
presents in the water.
■The spots can be removed with a mild
abrasive agent; never use chlorine
based materials, steel wool, etc.
1
2
1b

19
DESCRIPTION OF THE CONTROL PANEL
A"ON/OFF" button
B"PROGRAMME SELECTION" button
C "DELAY START" button
D"START"/"RESET" button
(start/cancelling programme)
E "ECO" option button
F "ALL IN 1" option button
G
"WASH POWER" button
H "PROGRAMME SELECTION" lights
I "SALT EMPTY" light
L"PROGRAMME STATUS" lights/
"DELAY START" time lights
M "OPTION SELECTION" lights
N
"WASH POWER" lights
O Programme guide
DIMENSIONS
TECHNICAL DATA
CONSUMPTION (main programmes)*
Programme Energy (kWh) Water (L)
INTENSIVE
UNIVERSAL
ECO
ULTRA RAPID 24'
1,97
1,35
0,90
0,59
20
14
10
9
Width x Height x Depth (cm) 60 x 85 x 60
Depth with door open (cm) 120
EN 50242 place load
Capacity with pans and dishes
Water supply pressure (MPa)
Fuse / Power input / Supply voltage
12
8 persons
Min. 0,08 - Max. 0,8
See rating plate
Power consumption of the off-mode and of the left-on mode: 0,30 W / 0,80 W
*Values are measured in a laboratory according to European Standard EN 50242 (consumption may
vary according to conditions of usage).
59,8 x 82 x 57,3
117
With working top Without working top

20
PROGRAMME SELECTION
AND SPECIAL FUNCTIONS
(Use in conjunction with programme guide)
"WASH POWER" button
This button allows you to modify the wash
intensity, according to how dirty your dishes
are, by modifying the wash time and
temperature.
Press the button to increase the intensity of
wash cycle ( indicator light) or to reduce
the intensity of wash, this also allows you to
decrease the wash length time ( indicator
light).
The combination of this button with the 4
main wash programmes enables you to
have 8 additional wash cycles (achieving a
total of 12 wash programmes.
IMPORTANT
When the dishwasher is switched on,
the setting last used will be indicated.
Programme settings
■Open the door and place the dirty dishes
inside the appliance.
■Press the "ON/OFF" button .
All the programme indicator lights will
flash.
■Choose a programme by pressing the
"PROGRAMME SELECTION" button.
■If you wish, press the "WASH POWER"
button.
■If you wish to select an option, press the
corresponding button (the indicator light
will turn on).
The option buttons can be selected or
deselected WITHIN one minute of the
programme commencing.
■Press the "START" button (the selected
programme indicator light will stop
flashing and remain on.
■When the door is shut, after an audible
signal has sounded, the programme will
start automatically.
WITHIN one minute of the programme
commencing, another programme
can be selected, simply by pressing
the "PROGRAMME SELECTION"
button (it is also possible to change
the "WASH POWER" button setting ).
"IMPULSE" programmes
The “IMPULSE” programmes use impluse
washing technology, which reduces
consumption, noise and increases
performances.
IMPORTANT
The “intermittent” working of the
washing pump MUST NOT BE
considered a malfunction, it is a
characteristic of the impulse washing
so must be considered a normal
function of the programme.
Programme interruption
Opening the door when a programme is
running is not recommended especially
during the main wash and final hot rinse
phases. However, if the door is opened
while a programme is running (for example,
to add dishes) the machine stops
automatically.
Close the door, without pressing any
buttons. The cycle will start from where it
left off.
IMPORTANT
A running program can be interrupted
without opening the door by
pressing the "ON/OFF" button. In
this case, simply press the "ON/OFF"
button again to restart the cycle from
where it left off.
WARNING!
If you open the door during the
drying cycle, an audible audio signal
advises you that the drying cycle has
not yet finished.