Baumatic BDW13 User manual

1
BDW13 60 cm Fully integrated
full height electronic dishwasher

BDW13 &
BDW14 DISHWASHER
60CM FULL HEIGHT DISHWASHER
IMPORTANT!
DD 02/11
/
07
PLEASE READ THIS MANUAL AND
K
E
E
P IT FOR FUTURE R
E
FER
E
NCE
!
THIS MANUAL CONTAINS SECTIONS OF SAFETY INSTRUCTIONS, OPERATING
INSTRUCTIONS & TROUBLESHOOTING TIPS, ETC.

MINIMUM AND MAXIMUM PLATE SIZES….35
ENVIRONMENTAL NOTE………………………..36
CONTACT DETAILS……………………………….37
BAUMATI C BDW13, BDW14 dishwasher user manual 2
HELP YOU SOLVE SOME
THE NEED TO ASK FOR HELP
TECHNICIANS.
RESERVES THE RIGHT TO MAKE
WITHOUT GIVING PRIOR
2
PLEASE NOTE:
THE MANUFACTURER
MODIFICATIONS TO PRODUCTS
NOTICE.
BEFORE ALLINGC
FOR SERVICE
REVIEWING THE SECTION ON
TROUBLESHOOTING TIPS WILL
COMMON PROBLEMS WITHOUT
FROM PROFESSIONAL
CONTENTS
• SAFETY FIRST!
SAFETY INFORMATION .……………..…………3
*Please read this before using your dishwasher!
• KNOWING YOUR
DISHWASHER
CONTROL PANEL ………………………..……..…4
DISHWASHER FEATURES …………..………….4
• USING YOUR
DISHWASHER
WATER SOFTENER …………………..………...5-6
DETERGENT ………………..............................6
RINSE AID ………………….............................7
LOADING YOUR DISHWASHER…..….......8-11
STARTING A WASH CYCLE ……………….12-14
UNLOADING AT THE END OF A CYCLE…....15
FILTERING SYSTEM ………………..…….…….16
CLEANING AND MAINTAINING
YOUR DISHWASHER …………………….…16-18
• BEFORE YOU CALL FOR
SERVICE…
TROUBLESHOOTING ………………….…19-23
ERROR CODES ……………………………….…..24
• MISCELLANEOUS
CHARACTERISTICS ………….………….……...25
HOW TO INSTALL ……….…….…..……....26-33
FINAL CHECKLIST BEFORE STARTING…….34

IN YOUR DISHWASHER. PLEASE SEE PAGE 8 FOR A LIST
2) Load sharp knives with the handles up to pre
v
ent
3
BAUMATI C BDW13, BDW14 dishwasher user manual
IMPORTANT SAFETY INFORMATION
READ BEFORE USING!
ON ITS DOOR OR DISH RACKS – TIPPING
DISHWASHER AS THERE COULD BE
• SUPERVISE YOUNG CHILDREN TO ENSURE
USE THE APPLIANCE.
COMPARTMENT OF YOUR OLD APPLIANCE
BEFORE USING
SOME ITEMS ARE UNSUITABLE FOR WASHING
OF THESE ITEMS.
DO NOT TAMPER WITH THE CONTROLS.
WHEN LOADING ITEMS TO BE WASHED:
1) Keep sharp items like knives away from the door
seal.
AFTER USE
injuries.
• ALWAYS KEEP THE DOOR CLOSED TO AVOID DANGER
OF TRIPPING.
ONLY USE AUTOMATIC DISHWASHER
• CHECK THAT THE DETERGENT DISPENSER IS EMPTY
DETERGENT, NOT SOAP OR LAUNDRY DETERGENT. AFTER COMPLETION OF WASH CYCLE.
NEVER USE SOLVENTS AS THIS COULD RESULT IN AN
• IF LEAVING UNUSED FOR A LONG TIME,
EXPLOSION! DISCONNECT THE WATER SUPPLY (SEE PP. 18, 30).
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY BEFORE
USING YOUR DISHWASHER FOR THE FIRST TIME!
3
DURING USE
• DO NOT TOUCH THE HEATING ELEMENT
DURING OR IMMEDIATELY AFTER USE.
CHILD SAFETY
• DO NOT ABUSE OR FORCE THE
DISHWASHER. DO NOT SIT ON OR STAND
HAZARD.
• KEEP CHILDREN AWAY FROM DETERGENT,
RINSE AID AND THE OPEN DOOR OF THE
DETERGENT LEFT INSIDE.
THEY DO NOT PLAY WITH THE APPLIANCE.
• SUPERVISE INFIRM PERSONS IF THEY MUST
• REMOVE THE DOOR TO WASHING
BEFORE DISCARDING IT.
ELECTRICAL SAFETY
• NOTE - This appliance must be grounded. In
the
event of a malfunction or breakdown,
grounding
w ill reduce the risk of electr i c
shock
by providing a path of least resistance
of e l ectr i cal current. You wi ll be ab l e to te ll if
i t is because a non-grounded appliance wil l
give off an e l ectrica l d i scharge.
• Manufacturer dec li nes al l responsibi li ty for
any damage due to non-grounding of
appliance.
• DURING THE GUARANTEE PERIOD ONLY BAUMATIC
SERVICE
ENGINEERS OR AN AUTHORISED AGENT
OF BAUMATIC SHOULD CARRY OUT REPAIRS ON
THIS
UNIT .
• DO NOT USE IF THE SUPPLY CORD IS DAMAGED.
• FOR INSTALLATION PROCEDURE PLEASE CONSULT
PAGES
26 – 33.
• DO NOT USE YOUR DISHWASHER UNLESS
ALL ENCLOSURE PANELS ARE PROPERLY
IN PLACE. OPEN THE DOOR VERY
CAREFULLY IF THE DISHWASHER IS
OPERATING. THERE IS A RISK OF WATER
SQUIRTING OUT.

(ADJUS
T
ABLE)
8 CUTLERY BASKET
4 WATER SOF
T
ENE
R
BAUMATI C BDW13, BDW14 dishwasher user manual 4
CONTROL PANEL
NOTE: YOUR DISHWASHER’S CONTROL PANEL IS ON THE TOP LIP OF THE DOOR. IF
YOUR APPLIANCE IS BEING INSTALLED UNDER A WORKTOP, YOU WILL NEED TO OPEN
THE DOOR TO SEE THE CONTROL PANEL.
1
Program Indicator Light: when you select a washing program, the corresponding light will display .
2 Program Key: Press to select a washing program. Multiple presses select different programs. See page 13 for
how
to program the washing cycle you want .
3 Salt and Rinse Aid Warning L i ght: Comes on when the softener or rinse aid dispenser needs refilling . Note
that when you first use your dishwasher, the salt & rinse aid lights do not go out immediately .
4 Half Washing Light: Comes on when you select the ‘Hal f wash’ option.
5 Half Washing Key: Press to select ‘Hal f wash’ program. * (Optional half wash i ng means that the lower
spray
arm does not run, so you should load the upper basket only).
6 Delay Start T i me: Displays the delay start time , the water temperature & ERROR CODES (see p . 24) .
7 De l ay Key: Press this key to set the delay start time . You can delay starting your washing cycle up to 24 hours.
One press on this delays the start of the washing cycle by one hour .
8 Power On light: Comes on when the ‘ON / OFF’ Button is pressed down .
9 ON / OFF Button: Turns the power supply on and off.
DISHWASHER FEATURES
1 ADJUSTABLE UPPER BASKET 5 MAIN FILTER 9 COARSE FILTER
2 SPRAY ARMS 6 DETERGENT DISPENSER 10 RINSE AID DISPENSER
3 LOWER BASKET 7 CUP & GLASS SHELF 11 DRAIN PIPE CONNECTOR
12 INLET PIPE CONNECTOR
4
NOTE: YOUR DISHWASHER CAN RUN A TEST CYCLE. THIS HAPPENS WHEN YOU PRESS EITHER THE PROGRAM KEY OR THE DELAY
TIMER KEY BEFORE PRESSING THE ON / OFF BUTTON. WHEN THIS HAPPENS, YOUR DISHWASHER WILL NOT RUN BUT WILL ENTER THIS
TEST CYCLE INSTEAD. PLEASE SEE PAGE 19 (TROUBLESHOOTING SECTION) FOR MORE INFORMATION AND HOW TO CORRECT IT.

DISH
W
ASHER.
SURE NOT TO ADD SALT AND/OR RINSE AID
TO THE APPLIANCE AS THESE TABLET
MINE
R
ALS F
R
OM THE WA
T
E
R
. INDIVIDU
A
L CHEMIC
A
LS
A
ND M
A
Y C
A
USE
5
BAUMATI C BDW13, BDW14 dishwasher user manual
Note on chemicals used by the dishwasher
• Your dishwasher is equipped with an adjustable rinse aid and salt container. Using individual detergents,
rinse aid and salt will give the best possible results as this will give the correct dosage of each chemical to
suit your needs. Using Two-in-One or Three-in-One tablets may not give the best results when used in
your appliance, and may not be suitable for the type of water supply in your home, as they contain pre-
determined quantities of salt, rinse aid and detergent and cannot be adjusted to the individual
requirements.
If you are going to use 3-in-1 (or 2-in-1) tablets, we suggest that you contact the manufacturer before use
or if you experience poor results in the wash performance and ask for assistance from them.
WARNING!
ONLY USE DISHWASHER SALT IN YOUR
NOTE:
IF YOU USE 3-IN-1 OR 2-IN-1 TABLETS, BE
TYPES ALREADY CONTAIN SALT AND/OR
THE LIME IN HARD WATER MAKES DEPOSITS FORM ON RINSE AID. ADDING SALT AND RINSE AID
DISHES AND UTENSILS. YOUR DISHWASHER HAS A TO YOUR DISHWASHER’S COMPARTMENTS
SPECIAL SOFTENING FEATURE THAT USES SALT IN A CYCLE INVOLVING A 3-IN-1 OR 2-IN-1
WATER
SOFTENING
FEATURE
SPECIFICALLY DESIGNED TO ELIMINATE LIME AND TABLET WILL RESULT IN OVERDOSING OF
OVERFLOWING OF WATER AND SUDS.
LOADING SALT INTO THE SALT CONTAINER
• REMOVE THE LOWER BASKET & THEN
UNSCREW
AND REMOVE THE CAP
FROM
THE SALT CONTAINER.
• IF YOU ARE FILLING THE CONTAINER
FOR
THE FIRST TIME, FILL WITH
APPROX.
1 LITRE OF WATER.
• PLACE THE END OF THE SUPPLIED
FUNNEL
INTO THE HOLE & ADD 1 . 2 Kg
OF
SALT. NOTE: IT IS NORMAL FOR A
SMALL
AMOUNT OF WATER TO COME
OUT
OF THE CONTAINER .
5

BAUMATIC BDW13/14 dishwasher user manual
6
6
SETTING THE WATER SOFTENER LEVEL
YOU CAN ADJUST THE AMOUNT OF SALT USED BY THE DISHWASHER TO SOFTEN WATER TO GET
THE BEST WASHING RESULTS, BASED ON THE HARDNESS OF WATER IN YOUR AREA.
1 UNSCREW THE CAP FROM THE SALT
CONTAINER.
2 THERE IS A RING ON THE NECK OF THE
CONTAINER. ROTATE THE RING IN AN
ANTICLOCKWISE DIRECTION FROM THE “-”
SETTING TOWARDS THE “+” SETTING
ACCORDING TO THE HARDNESS OF WATER
IN USE. SEE TABLE BELOW.
NOTE
1. THE SALT CONTAINER MUST BE REFILLED WHEN THE
SALT WARNING LIGHT COMES ON. ALTHOUGH THE
SALT CONTAINER MAY BE FULL, THE INDICATOR LIGHT
MAY NOT GO OUT UNTIL THE SALT HAS DISSOLVED.
2. IF THERE ARE SALT SPILLS, A SOAK PROGRAM CAN
BE RUN TO WASH AWAY SPILLAGE BEFORE USING THE
MACHINE.
3. CLEAR ANY SALT GRANULES AWAY FROM THE
CONTAINER OPENING.
ADJUSTMENTS SHOULD BE MADE ACCORDING TO THE TABLE BELOW:
WA TER H ARDNESS
Cl ark e Degrees dH mmol /l Selector Position Salt con sum ption
(gra m/cycle)
Au to nomy
(cycles/1.2kgs)
0~14 0~18 0~ 1. 8 /0/
14~36 18~44 1. 8~ 4.4 -20 60
36~71 44~89 4. 4~ 8.9 MED 40 30
71 89 8. 9 +60 20
Contact your local water board for information on the hardness of your water supply.
DETERGENT “How much do I use?”
To OPEN the DETERGENT DISPENSER DOOR, use the CATCH on its LOWER SIDE.
*NOTE: SEE P.13 – WASH CYCLE TABLE for AMOUNT of DETERGENT to use.
NOTE:
• ALWAYS CHECK THE WASH CYCLE TABLE
FOR DOSAGE ADVICE. NEVER OVERFILL
THE DISPENSER.
• DO NOT OVERDOSE TO PREVENT THE
FORMATION OF DEPOSITS (THE WATER
SOFTENING FEATURE ALREADY TAKES CARE
OF THIS!).
THE HARDER YOUR WATER, THE MORE DETERGENT
YOU MAY NEED. ADJUST THE DOSE JUST BY SMALL
AMOUNTS UNTIL YOU FIND THE CORRECT AMOUNT
OF DETERGENT TO USE.

FORMING D
R
OPLETS ON YOU
R
DISHES
THAT
CAN CAUSE SPOTS AND STREAKS. IT
• TO OPEN THE DISPENSER, TURN THE CAP TO
• POUR THE RINSE AID INTO THE DISPENSER.
DISHWASHE
R
DOOR.
‘OPEN’ ARROW & TURN IT TO THE CLOSED
7
BAUMATI C BDW13, BDW14 dishwasher user manual
• THE RINSE AID IS RELEASED DURING THE
FINAL
RINSE TO PREVENT WATER FROM
RINSE AID
ALSO IMPROVES DRYING BY ALLOWING
WATER
TO FALL OFF THE DISHES.
• YOUR DISHWASHER IS DESIGNED TO USE
LIQUID
RINSE AIDS. THE RINSE AID
DISPENSER
CAN BE FOUND INSIDE THE
DOOR
NEXT TO THE DETERGENT
DISPENSER. TO FILL THE DISPENSER, OPEN
THE
CAP AND POUR THE RINSE AID INTO
THE DISPENSER UNTIL THE LEVEL
INDICATOR TURNS COMPLETELY BLACK.
THE
DISPENSER HOLDS ABOUT 100ML OF
LIQUID
RINSE AID.
• BE CAREFUL NOT TO OVERFILL THE
DISPENSER
– THIS COULD CAUSE
FROTHING.
WIPE AWAY SPILLS WITH A
THE ‘OPEN’ (LEFT) ARROW AND LIFT IT OUT.
DAMP CLOTH. DON’T FORGET TO REPLACE
THE
CAP BEFORE YOU CLOSE THE
BE CAREFUL NOT TO OVERFILL.
NOTE
: IF YOU HAVE SOFT WATER, YOU MAY NOT
• REPLACE CAP BY INSERTING IT ALIGNED WITH
NEED RINSE AID FOR IT MAY CAUSE A WHITE FILM
(RIGHT) ARROW.
TO DEVELOP ON YOUR DISHES.
ADJUSTING THE RINSE AID DISPENSER
•
As with detergent, the amount of rinse
aid needed for your dishes depends on
the hardness of the water in your area.
Too much rinse aid can result in
foaming and cause cloudiness or
streaks on your dishes. If your water
is very soft, you may not need rinse
aid. You can always dilute the rinse
aid with an equal amount of water.
The rinse aid dispenser has six settings . ALWAYS START WITH THE DISPENSER SET ON “1”. IF SPOTS & POOR
DRYING
ARE A PROBLEM , INCREASE THE AMOUNT OF RINSE AID DISPENSED BY REMOVING THE DISPENSER
LID AND ROTATING THE DIAL TO “2”. IF THE DISHES ARE STILL NOT DRYING PROPERLY OR ARE SPOTTED,
ADJUST
THE DIAL TO THE NEXT HIGHER NUMBER UNTIL YOUR DISHES ARE SPOT-FREE .
*** NOTE: Please read the notes for detergent use on p. 13.
WHEN TO REFILL THE RINSE
AID DISPENSER - If the rinse aid
warning
light ( SEE control panel) is not on, you
can
judge the rinse aid level by looking at the
black
dot on the rinse aid dispenser. As the
rinse aid level decreases, the black dot shrinks.
Never
let the rinse aid get below ¼ full.
7

BAUMATI C BDW13, BDW14 dishwasher user manual 8
LOADING NOTE:
YOUR FOR BEST PERFORMANCE, FOLLOW THESE
LOADING GUIDELINES. FEATURES AND
APPEARANCE OF RACKS & CUTLERY
BASKETS MAY VARY FROM YOUR MODEL.
DISHWASHER
BEFORE LOADING!
• REMOVE ALL SCRAPS OF FOOD.
• EMPTY DRINKS & LIQUIDS FROM CUPS.
• SOFTEN BURNT-ON FOOD IN PANS BY SOAKING.
DO NOT PUT THESE ITEMS IN YOUR DISHWASHER:
• BRONZE • OLDER • STEEL ITEMS
CUTLERY CUTLERY SUBJECT TO
WITH GLUED RUSTING
• SAUCEPANS PARTS
WITH • WOODEN
WOODEN PLATTERS
HANDLES • BONDED
CUTLERY
• CUTLERY ITEMS OR • ITEMS MADE
WITH DISHES FROM
WOODEN, SYNTHETIC
HORN, CHINA FIBRES (eg.
OR MOTHER • PEWTER OR SPONGES)
OF PEARL COPPER ITEMS
HANDLES
• DELICATE,
• PLASTIC • LEAD CRYSTAL REPAIRED OR
ITEMS THAT GLASS PAINT /
ARE NOT HEAT PATTERN
RESISTANT OVERLAID
CHINA
Note :
Do not wash stainless stee l and silver cutlery t ogether. Iron objects can rust
and
stain other items. Aluminium t ends to go black. Copper, pewter & brass
stain.
8

COOKWARE SO THAT THEY DO NOT
WATER. ALWAYS PLACE GLASSES,
(POSITION ‘1’ IN THE FIGURE ON THE RIGHT)
THE FIGURE ON THE RIGHT) IN THE GROOVE
Servin
g
9
BAUMATI C BDW13, BDW14 dishwasher user manual
HOW TO USE THE UPPER RACK
THE UPPER RACK IS FOR MORE DELICATE
AND LIGHTER DISHWARE SUCH AS
GLASSES, COFFEE & TEA CUPS, SAUCERS,
PLATES, BOWLS,
AND SHALLOW PANS
(PROVIDED THESE ARE NOT TOO DIRTY).
POSITION THE DISHES AND
GET MOVED BY THE SPRAY OF
CUPS & BOWLS UPSIDE DOWN.
NOTE :
YOUR DISHWASHER COMES WITH AN
ADJUSTABLE TOP RACK (BASKET) –
PICTURED AT RIGHT. ITS HEIGHT CAN
BE ADJUSTED BY UNDOING THE FRONT
RAIL CLIPS, REMOVING THE RACK
COMPLETELY AND LATCHING THE
WHEELS OF THE LOWER LEVEL
1
OR THE HIGHER LEVEL (POSITION ‘2’ IN 2
OF THE RAIL.
PLEASE NOTE: WHEN THE UPPER
BASKET IS IN THE FULLY RAISED
POSITION HE MAXIMUM SIZET
PLATE
THAT CAN BE ACCOMODATED IS 28
CM.
LOADING GUIDE (UPPER RACK):
41 Cups
52 Small
1
3Bowls
3 Large
Serving
Bowls
4 Glasses
5 Saucers
6 Dishes
277 Plates
6
9

BAUMATI C BDW13, BDW14 dishwasher user manual 10
***NOTE
***: THE UPPER RACK HAS
SIDE FLAPS (PICTURED AT LEFT ABOVE BASKET).
THERE ARE 4 (2 ON EACH SIDE).
THESE CAN BE ADJUSTED INTO 2
POSITIONS = POSITION 1 (HIGH)
AND POSITION 2 (LOW).
TO MOVE THE FLAPS BETWEEN THESE
POSITIONS, FIND THE LARGE HINGES
CLASPING EACH FLAP TO THE UPPER
RACK. THERE ARE TWO OF THESE AT
EITHER END OF EACH FLAP. GENTLY PULL
BOTH CLASPS OFF THE WIRE RACK AND
MOVE THE FLAP TO THE DESIRED
POSITION. BE CAREFUL IF YOU HAVE
LONG FINGERNAILS!
POSITION 1
THE UPPER POSITION WILL ACCOMMODATE ITEMS SUCH AS GLASS TUMBLERS
(PLACED BENEATH FLAP) AND WINE GLASSES. WINE GLASSES CAN BE PLACED
UPSIDE DOWN SO THAT THE NECK NESTLES SNUGLY IN THE GROOVES AT SIDE OF
FLAP WITH THE BASE OF THE GLASS FACING UPWARD.
POSITION 2
WHEN THE FLAPS ARE MOVED TO THE LOWER POSITION, THEY CAN BE USED TO
HOLD ADDITIONAL TUMBLERS, CUPS AND MUGS. ALWAYS CHECK THAT YOU ARE
ONLY PLACING ITEMS ON THE FLAPS THAT WILL CLEAR THE CEILING HEIGHT OF
YOUR DISHWASHER WHEN YOU PUSH THE RACK BACK IN. BE PARTICULARLY
CAREFUL WITH LONG-STEMMED GLASSWARE SUCH AS CHAMPAGNE GLASSES –
BREAKAGE HAZARD!
HOW TO LOAD THE LOWER RACK:
PLACE LARGE ITEMS THAT ARE HARD TO CLEAN IN THE LOWER RACK: eg. POTS, PANS,
LIDS, SERVING DISHES, BOWLS.
1.
OVAL PLATTER.
2.
DINNER PLATES.
3.
SOUP PLATES.
4.
DESSERT
DISHES.
5.
CUTLERY
BASKET
.
• POTS, SERVING BOWLS, ETC. MUST ALWAYS BE PLACED UPSIDE DOWN.
• DEEP POTS SHOULD BE SLANTED TO LET WATER FLOW OUT.
• THE BOTTOM RACK FEATURES FOLD DOWN BASKETS SO THAT LARGER OR MORE POTS
& PANS CAN BE LOADED.
10

11
BAUMATI C BDW13, BDW14 dishwasher user manual
CUTLERY BASKET
CUTLERY SHOULD BE PLACED IN THE CUTLERY BASKET WITH HANDLES ALWAYS POINTING
DOWNWARD (AT THE BOTTOM). VERY LONG UTENSILS (LADLES, etc.) SHOULD BE PLACED
HORIZONTALLY AT THE FRONT OF THE UPPER RACK.
1 Forks
2 Soup Spoons
3 Dessert Spoons
4 Teaspoons
5 Knives
6 Serving Spoons
7 Gravy Ladle
8 Serving Fork
NOTE
11
:
• WHEN YOU ARE SATISFIED YOU HAVE LOADED ALL THE UTENSILS
AND DISHES YOU WANT TO WASH AND HAVE ADDED THE PROPER
AMOUNT OF DETERGENT TO THE DISPENSER (REMEMBER TO CHECK THE
TABLE ON PAGE 13 FOR THE DOSE THAT’S RIGHT FOR THE WASHING CYCLE YOU
WANT), ENSURE THE RACKS ARE PUSHED ALL THE WAY BACK INTO
YOUR DISHWASHER AND CLOSE THE DOOR.
• YOU ARE NOW READY TO START A WASH CYCLE (SEE NEXT PAGE).

.
BAUMATI C BDW13, BDW14 dishwasher user manual 12
STARTING A WASH CYCLE
P
1) MAKE SURE THAT YOUR DISHWASHER’S PLUG
5) OPEN THE DOOR, PRESS THE ‘ON/OFF’
BUTTON AND THE ‘ON/OFF’ LIGHT WILL
COME ON.
HAS BEEN PUSHED ALL THE WAY INTO THE WALL
SOCKET.
2) MAKE SURE THAT THE WATER SUPPLY IS TURNED
ON TO FULL PRESSURE.
6) PRESS THE ‘P’ KEY (PROGRAM KEY) TO
SELECT THE ‘WASH CYCLE’. SEE TABLE
ON NEXT PAGE FOR WASH CYCLE TYPES.
3) LOAD YOUR DISHWASHER (SEE THE SECTION
ENTITLED ‘LOADING YOUR DISHWASHER’, PAGES
8-11).
7) CLOSE THE DOOR. THE WASHING WILL
START AFTER APPROXIMATELY TEN
SECONDS.
4) POUR IN DETERGENT (SEE THE SECTION
ENTITLED ‘SALT, DETERGENT & RINSE AID’),
PAGES 5-7.
**** Note:
When you turn your dishwasher on, the number ‘OO’ should show on the display. If you see
any other digits, such as ‘17’ or ‘01’, ‘02’, ‘03’, etc., please refer to the trouble-shooting section on page 19.
* REMEMBER *: YOU CAN PROGRAM YOUR DISHWASHER UP TO 24 HOURS IN
ADVANCE BY PRESSING THE DELAY BUTTON MULTIPLE TIMES UNTIL THE
DESIRED DELAY HAS BEEN SET.
* Note: Each time you press the delay timer key, you will move the start of your wash cycle forward by one hour.
Delay Timer Key (7)
Approximate Timing of Wash Cycles
Intensi v e
Normal
s.
12
(
stron
g
)
133
Econom y
112
mins.
Rinse
106
mins.
Glass
51
mins.
Rapid
73
mins.
Soap
48 7
mins. mins.
min

13
BAUMATI C BDW13, BDW14 dishwasher user manual
5 grams (pre)
/ 22 grams
(main)
5 grams (pre)
/ 22 grams
(main)
22 grams
15 grams
15 grams
OVERFLOW PROTECTION
YOUR BAUMATIC DISHWASHER HAS AN OVERFILL PROTECTION DEVICE WHICH AUTOMATICALLY SHUTS OFF
THE INLET VALVE AND STARTS THE DRAIN PUMP IF THE WATER OVERFLOWS. IF THIS OCCURS THEN TURN OFF
THE MAINS WATER SUPPLY BEFORE CALLING THE SERVICE DEPARTMENT. IF THERE IS WATER IN THE BASE
PAN BECAUSE OF AN OVERFILL OR SMALL LEAK, THE WATER SHOULD BE REMOVED BEFORE RESTARTING THE
DISHWASHER. A BUCKET AND A SPONGE ARE RECOMMENDED TO HAVE AT HAND FOR THIS PURPOSE.
13

BAUMATI C BDW13, BDW14 dishwasher user manual 14
FORGET TO ADD A DISH?
A FORGOTTEN DISH CAN BE ADDED AT ANY TIME BEFORE THE DETERGENT
DISPENSER OPENS.
• OPEN THE DOOR A LITTLE TO STOP THE WASHING.
• WAIT ABOUT TEN SECONDS. AFTER THE SPRAY ARMS STOP WORKING,
YOU CAN OPEN THE DOOR COMPLETELY.
• ADD FORGOTTEN DISHES.
• CLOSE THE DOOR, THE DISHWASHER WILL WORK AFTER TEN SECONDS.
NEED TO INTERRUPT A CYCLE?
If an emergency arises , you can stop the machine at any time. Remember to wait
approx . 10 second s b efore you open the d oor full y, a s the s pray ar ms continue to tu rn
after the power ha s been cut and could spray hot wat er up at yo u.
DO NOT PRESS THE ‘ON/OFF’ BUTTON AS THIS WILL RESET THE WHOLE
WASH
CYCLE! YOU JUST NEED TO PULL THE DOOR OPEN – DO NOT TOUCH
ANY
BUTTONS!
SET THE WRONG CYCLE?
If you s et the wrong wash prog r am , you can alway s c ancel the one the machine i s
working on by pre s sing the ‘ON/OFF’ button to switch your dishwasher off, waiting a
few seconds b efore opening the doo r to change the cycle (see p.12 to recap on how to
start
a washing cycle). Don’t forget to add detergent for the new cycle. Yo ur
dishwashe r will automatically d r ain any water away and begin the new cycle.
TAKE CARE WHEN OPENING THE DOOR DURING
WASHING. THE HOT WATER IN THERE MAY SCALD YOU IF YOU OPEN
THE DOOR TOO QUICKLY!
14

15
BAUMATI C BDW13, BDW14 dishwasher user manual
AT THE END OF THE WASH CYCLE
15
WHEN YOUR DISHWASHER’S WASHING CYCLE HAS FINISHED:
• THE ALARM WILL SOUND FOR EIGHT SECONDS.
• OPEN THE DOOR OF YOUR DISHWASHER & SWITCH YOUR
DISHWASHER OFF USING THE ‘ON/OFF’ KEY.
• WAIT A FEW MINUTES BEFORE UNLOADING THE
DISHWASHER TO AVOID HANDLING THE DISHES AND
UTENSILS WHILE THEY ARE STILL HOT AND MORE
SUSCEPTIBLE TO BREAKAGE.
• THEY WILL ALSO DRY BETTER IF YOU LEAVE THEM IN FOR
A WHILE.
NOTE: THESE MODELS F EATURE BUILT-IN RES I DUAL DRYING .

BAUMATI C BDW13, BDW14 dishwasher user manual 16
FILTERING SYSTEM
FOR YOUR CONVENIENCE , WE HAVE PLACED THE FILTERING SYSTEM WITHIN EASY REACH INSIDE THE
TUB
. THE FILTER REMOVES BITS OF FOOD TRAPPED IN THE FILTER FROM THE WASH WATER SO IT CAN BE
RECIRCULATED
DURING THE CYCLE. THERE ARE THREE PARTS TO THE FILTERING SYSTEM: 1) The Main F ilt er,
2) The Coarse Filter & 3) The Fine F il ter .
1 MAIN FILTER
Food and soil particles trapped by this filter are
pulverized by a special jet on the lower spray arm and
washed down the drain.
2 COARSE FILTER
Larger items, such as pieces of bone or glass that could
clog the drain are trapped in the coarse filter. To
remove an item caught in this filter, gently squeeze
the tabs on top of this filter and lift it out.
3 FINE FILTER
This filter holds soil and food residue in the sump area
and prevents it from being re-deposited on the dishes
during a cycle.
Caring
for your Dishwasher
CLEANING THE OUTSIDE SURFACES OF YOUR APPLIANCE
• TO CLEAN THE EXTERIOR OF YOUR DISHWASHER (INCLUDING THE CONTROL PANEL), USE A LIGHTLY
DAMPENED CLOTH THEN DRY THOROUGHLY. NEVER USE SHARP OBJECTS, SCOURING PADS OR
HARSH CLEANERS ON ANY PART OF THE APPLIANCE. SOME PAPER TOWELS CAN SCRATCH.
• TO CLEAN THE EDGE AROUND THE DOOR,
ONLY EVER USE A SOFT WARM, DAMP RAG.
DO NOT USE A SPRAY CLEANER HERE OR
WHEN CLEANING THE DOOR PANEL AS THIS
MAY HARM THE DOOR LOCK AND
ELECTRICAL PARTS.
CLEANING THE SPRA Y ARMS
THE SPRAY ARMS NEED REGULAR CLEANING AS HARD WATER RESIDUES WILL CLOG THEIR
JETS & BEARINGS. TO REMOVE THE SPRAY ARM, SCREW OFF THE NUT TO TAKE OUT THE
WASHER ON TOP OF THE SPRAY ARM AND REMOVE THE ARM. WASH THE ARMS IN SOAPY
WARM WATER & USE A SOFT BRUSH TO CLEAN THE JETS. REPLACE THE SPRAY ARM AFTER
RINSING IT THOROUGHLY.
16

17
BAUMATI C BDW13, BDW14 dishwasher user manual
CLEANING THE FILTERS
• THE FILTER ASSEMBLY MUST BE KEPT CLEAN FOR BEST PERFORMANCE. You should remove the
larger bits of food trapped in the filter after each wash cycle by rinsing the semicircular filter and
cup under running water. To remove the filter assembly, pull up on the cup handle.
• The entire filter assembly should be cleaned at least once a month.
• To clear the coarse filter and the fine filter, use a cleaning brush. Then, reassemble the filter parts
as shown in the figure above and reinsert the entire assembly in the dishwasher in its seat & press
downward to secure it.
• Improper replacement of the filter may impair appliance performance and damage dishes and
utensils.
• Warning - never run the dishwashe r without the filters
in place!
• Warning - Before clea ni ng the i nner cavity of the applia nce
always allow 30 minutes for th e Element to cool down to
avoid i n j ury!
17

BAUMATI C BDW13, BDW14 dishwasher user manual 18
HOW TO KEEP YOUR DISHWASHER IN SHAPE
A
FTER E VERY W ASH , leave the door slightly ajar so that moisture and odours are not trapped
inside.
R
EMOVE THE P LUG before cleaning or performing maintenance. Never run the risk of electric
shocks.
D
O N OT U SE S OLVENTS OR A BRASIVE C LEANING A GENTS to clean the exterior and the rubber
parts of the dishwasher. Only use a cloth and warm soapy water. To remove spots or stains
from the surface of the interior, use a cloth dampened with water and a little white vinegar,
or a cleaning product made specifically for dishwashers.
W
HEN YOU G O ON H OLIDAY , run a wash cycle with the dishwasher empty. Then unplug it, turn
off the water supply and leave the door slightly ajar to prevent odours and mould from
developing.
M
OVING THE A PPLIANCE is possible but KEEP IT UPRIGHT.
S
EALS can trap food, which in turn will cause odours. Periodic cleaning with a damp cloth or
sponge will prevent this from becoming a problem.
PROTECTING OUR ISHWASHER AGAINST REEZINGYDF
18
If your dishwasher is left in an unheated place during the winter, ask a
service technician to:
1) Cut off electrical power to the dishwasher. Remove fuses or trip circuit
breaker.
2) Turn off the water supply and disconnect the water inlet pipe from the water
valve & discharge hoses.
3) Drain water from the inlet pipe and water valve (Use a pan to catch the
water).
4) Reconnect the water inlet pipe to the water valve.
5) Remove the plastic sump cover in the tub bottom and use a sponge to soak
up water in the rubber boot.

19
BAUMATI C BDW13, BDW14 dishwasher user manual
BEFORE YOU CALL FOR SERVICE …
CHECKING AGAINST THE CHARTS BELOW MAY FIX YOUR PROBLEM.
PROBLEM POSSIBLE CAUSES
WHAT TO DO
• Replace fuse or reset circuit
breaker.
• Fuse blown, or the
circuit
breaker acted
• Remove any other appliances
feeding
from the same socket as
the
dishwasher .
• Power supply is not
turned
on
• Make sure the dishwasher is turned
on
and the door is closed securely .
• Check that the water supply is
connected
properly and the water is
turned
on.
• Water pressure is low
down the De l ay Timer key at the
• For situation A , Press and hold
• … And ( situation A )
the
number 17 is
showing
on the
display.
This means
that
your dishwasher
has
entered Test
Mode
– a factory
sequence
which you
need
not concern
yoursel
f with . This
happens
because the
Delay T i mer key was
pressed
before the
Dishwasher
doe
sn’t run!
same time as you’re pressing the
‘
ON/OFF’ button to switch the
dishwasher off. Wait a few
seconds then press only the
‘ON/OFF’ button again . You are
now ready to program your
dishwasher for a washing cycle as
per usual.
‘ON/OFF ’ key was
pressed.
• For situation B , Press ‘ ON / OFF’
button
to turn the dishwasher off.
Then
, press and hold down the
Program Key (‘P’) at the same
time
as you’re pressing the ‘ON /
• … Or ( situation B )
OFF’ button to switch the
the display shows one
of
the following: 0A,
dishwasher on again . You are now
ready to program a cycle as per
09, 08, 07, 06, 05,
usual.
04, 03, 02, 01, 00 .
• The system is designed to detect an
overflow.
When it does, it shuts off
Drain
Pump
doe
sn’t stop!
• Overflow the circulation pump and turns on
the drain pump. Call a Baumatic
Ltd approved technician .
19