Baumatic BFWM1206BL 60 cm 6kg User manual

BFWM1206BL 60 cm
6 kg Freestanding
washing machine
1

USER MANUAL FOR YOUR BAUMATIC
BFWM1206BL
60 cm 6 kg Freestanding
washing machine
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference; for
you or any person not familiar with the operation of the appliance.
JW 15/01/13
2

Contents
Environmental note 4
Important safety information 5 – 6
Specifications 7
Description of the appliance 8 - 11
Control panel 9
Program selections dial 10
Detergent drawer 11
Preparing the wash cycle 12 - 16
Preparing your garments for washing 12
A selection of wash care symbols 13
Detergents and conditioners 13 - 14
Wash program table 15
Wash program guidance 16
Selecting a wash program 16 - 18
Setting a wash program 16
End of cycle 16
Pausing a wash program 17
Delay start feature 17
Manual soaking 17
Easy-Iron function 18
Extra rinse function 18
Child lock function 18
Power off memory 18
Maintenance and cleaning 19 - 25
In daily use 19
Control panel and washing machine cabinet 19
Detergent drawer 19 - 20
The washing machine drum 20
Door 20
Cleaning the drain pump filter 21
Cleaning the water inlet filter 22
Winter storage 22
Removing stains 23
Stain removal rules 23
Stain removal guide 23 - 24
Poor wash results 25
Installation 26 - 31
Removing the transit bolts 26
Locating your washing machine 27
Connecting to the mains water supply 28
Connecting to the water outlet 29
Levelling the appliance 30
Power supply 30 - 31
Before first use maintenance wash 31
Error code failure system 32
General troubleshooting 33 – 34
Baumatic consumables 35
Technical data 36
Contact details 37
3

Environmental not
oThe packaging materials that Baumatic uses are environmentally
friendly and can be recycled.
oPlease discard all packaging material with due regard for the
environment.
4

Important safety information
Your safety is of the utmost importance to Baumatic.
Please make sure that you read this instruction
booklet before attempting to install or use the
appliance. If you are unsure of any of the
information contained in this booklet, please contact
the Baumatic Customer Care Department.
General Safety
oRepairs to your appliance must only be carried out by a
Baumatic engineer or one of its authorised service agents. Any
attempt by an inexperienced person to repair the appliance,
could result in injury or damage to your washing machine.
oIf you notice that the mains cable is damaged. The appliance
must not be used. The same applies if you notice that the
worktop, control panel or base area is damaged. As this could
allow access to the internal components of the machine.
oThe appliance should be turned off and isolated from the mains
supply, before either cleaning or maintenance work is attempted.
oThe mains cable must not be used to pull the plug out of the
electrical socket.
oThe machine should not be sprayed with water.
oThe glass of the porthole door may become hot during the higher
temperature wash programs.
oThe machine should be allowed to cool before carrying out an
emergency drain or cleaning the drain filter.
oIt is possible for small animals to chew either the mains cable or
water hoses, which could cause an electric shock hazard.
Installation
oThe installation instructions contained within this user manual
should be followed.
oIt is obligatory for the completed installation to comply with all
relevant building regulations and local water authority
requirements.
5

oBefore the first use of the appliance, we advise that a 95
degree anti-bacterial wash is completed. No garments
should be placed inside the machine; however a small
amount of detergent must be used.
During Use
oIt is recommended that the appliance is unplugged and the
water supply is turned off after the machine is used.
oThis appliance is only designed to wash normal domestic wash
loads. If you use your washing machine in any other way or it is
incorrectly used, then Baumatic accepts no liability for any
damage that might be caused and any guarantee will be void.
oNo attempt should be made to alter or modify the specifications
of this appliance.
oThe detergents that you place in this appliance should be
suitable for automatic washing machines. With regards to dosage
levels, the detergent manufacturer’s recommendations should be
followed.
oYou should not wash garments that have been in contact with
flammable materials.
oYour washing machine should not be used for dry cleaning.
oIf you use either dyes or bleaching agents inside this machine,
then you should consult with the manufacturer of these products
to make sure they are suitable for use in your washing machine.
Baumatic cannot be held responsible for any damage that may
result.
Child Safety
oYour washing machine should only be used by adults. You should
not allow children in the area of the machine unsupervised. You
should not let them touch the controls or play with the appliance.
oIt could be possible for a child or pet to gain access to the
washing machine through the porthole door. Therefore please
check the drum before using the appliance.
oAny packaging that is removed from the machine should be kept
away from children.
oAll detergents should be kept out of a child’s reach and in a safe
place.
6

Specifications
o15 wash programs
o6 kg wash load
o1200 rpm maximum spin speed
oElectronic control operation
oWash phase indicator
oDelay start
o180° door opening
oStainless steel drum
oOverflow protection
oPlastic tub
oEasy-Iron function
oAdjustable feet
oChild lock
oGlass door
Appliance dimensions
Height: 845 mm
Width: 595 mm
Depth: 530 mm
Ratings
Energy efficiency class (wash only) A+
Wash performance class A
Water extraction performance class B
For future reference please record the following information which can
be found on the rating plate and the date of purchase which can be
found on your sales invoice. The rating plate for your washing machine
will either be located on the right hand side of the cabinet or behind
the porthole door.
Model Number ……………………………….
Serial Number ……………………………….
Date of Purchase ……………………………….
7

Description of the appliance
Accessories
8

Control panel
1) additional functions for your washing cycle:
Economy: Reduces energy and water consumption – to be used
with smaller loads only.
Easy-Iron:Reduces the creases of clothes during a wash cycle
by not executing the last drain – until the start/pause button is
pressed.
Rinse+: Adds an extra rinse cycle to the end of your chosen
wash cycle.
NOTE: “Economy” and “Rinse+” cannot be used together.
2) Delay start button. Press this button to delay the start of the
washing cycle by 3, 6 or 12 hours.
3) Start / pause button. Press this button to start or pause a
washing cycle.
4) Washing program selection dial. Use this dial to select the
required washing program.
Child lock.Rinse+ button (1) and Delay start button (2).Enables the
user to lock all controls on the control panel.
Wash cycle progress indicator (Process). The current
wash cycle phase will light on the display to indicate the
progress of the program from “Washing”, “Rinse” and
“Spin”.
9

Program selection dial
NOTE: The symbol means that the water is cold (not
heated).
10

Detergent drawer
Main wash section
This compartment should have detergent placed in it (you should also
put a water softening agent in this section, if you use one). The
detergent will be added to the drum at the start of the main wash
program.
Conditioner section
This compartment should be used for liquid conditioners (fabric
softener, starch). They will be added to the wash load during the final
rinse.
Pre wash section
This compartment should have detergent placed in it, if you are going
to select a pre-wash before the main wash cycle.
11

Preparing the wash cycle
Preparing your garments for washing
oYour washing should be sorted out, according to
the fabric type and the wash care symbol that is
printed on the garment’s wash care label (see
separate section on wash care symbols).
oYour washing should also be sorted out
according to the degree of soiling.
oCheck all pockets on a garment to make sure that they are
empty.
oRemove any detachable metal items (badges,
paperclips, safety pins etc).
oZips should be closed, duvet covers and pillow cases should be
buttoned up and any loose straps should be tied up. This will
help to prevent other garments from getting damaged during the
wash.
oWoollens and knitted coloured fabrics should be turned inside out
before being washed in the appliance.
oSmall delicate items (tights, baby socks) should be placed in
either a washing net or a zipped pillow case.
oCurtains should be handled with particular care. All plastic hooks
or metal strips must be removed before being washed in the
appliance.
oColoured items and whites should be washed
in separate wash cycles.
oNew garments often contain an excess of dye, therefore it is
advisable to wash them separately for their first wash.
oGarments should be unfolded and shook out before being placed
inside the machine.
12

A selection of wash care symbols
Washing
Boiling
temp
95°C
Normal
temp
60°C
Normal
temp
40°C
Do not
wash!
Bleachable
in cold
water
Do not
bleach! Wool
seal
Dry
cleaning
Delicate
temp
30°C
Delicate
temp
40°C
Hand
wash
only
All
solvents
All but TRI
Benzine
only
Do not
clean!
Spin
dryer
Normal Low
High
Do not
dry!
Hang to
dry
Drip dry
Dry
flat
Ironing
110°C
150°C
200°C
Do not
iron!
oThe wash care symbols should be used to help you to select the
most suitable wash program. They will also help you to sort your
laundry into different loads, depending on the fabric type and the
highest temperature which the garment can be washed at.
Detergents and conditioners
IMPORTANT: Only detergents suitable for use in washing
machines should be used.
The amount of detergent that you need to use in your appliance, will
depend on
oThe degree of soiling.Lightly soiled garments in general
require less detergent.
oThe size of the wash load.A smaller wash load will require a
reduction in the amount of detergent.
oThe hardness of your tap water.The harder your water is,
then the more detergent you will need to use. The detergent
manufacturers normally give guidance as to how much extra
detergent should be used, depending on the hardness of the
water.
13

Liquid detergent
If you are using liquid detergent, then in the majority of cases the
liquid should be placed inside the dosing device supplied by the
detergent manufacturer and placed inside the drum. All instructions on
the detergent packaging should be followed.
Low temperatures
oThe enzymes in biological washing detergents work best at low
temperatures to provide excellent cleaning and stain removal
results, but not as low as 20°C.
oLiquid or gel detergents are particularly suitable for low
temperature washing as they dissolve easier and quicker than
powders or tablets.
Water softening agents
If your tap water is hard, then it may be prudent to utilise a water
softening agent. This will help to ensure that the appliance does not
become clogged with hard water deposits. You may also find that it will
allow you to lessen the amount of detergent that you are using.
When using any detergent or water softening
agent, the recommendations of the
manufacturers should be followed.
14

Wash program table
Wash
Program
Max
load
size
(Kg)
Max
Temp.
**
Rinse
times
Max
spin
speed
Default
Operation
Time
(mins)
Available optional functions
Delay Rinse+ Easy-
Iron Economy
Cotton cold
6
--
2
1000
69
√
√
√
√
cotton 30
℃
6
30
℃
2
1000
80
√
√
√
√
*cotton 40℃
6
40℃
2
1200
188
√
√
√
√
*cotton 60
℃
6
60
℃
2
1200
197
√
√
√
√
Pre-washing
6
60
℃
2
1000
214
√
√
√
×
Intensive
6
60
℃
2
1000
219
√
√
√
×
Anti-bac
3.5
95℃
2
1000
129
√
√
√
×
Quick wash 1.5 -- 2 800 15 √√√×
Spin only
6
--
0
1000
11
√
×
×
×
Rinse+spin
6
--
1
1000
16
√
√
√
×
Wool 40
℃
2
40
℃
2
600
56
√
√
√
×
wool cold
2
--
2
600
38
√
√
√
×
Kids wear
3.5
60
℃
4
1000
119
√
√
√
√
Synthetics
40
℃
3 40℃2 800 49 √√√√
Synthetics
cold
3 -- 2 800 39 √√√√
* Energy test program Cotton 60°C/40°C. These programs are suitable
for cleaning normally soiled cotton laundry and are the most efficient
programs.
** The actual water temperature may differ from the declared cycle
temperature.
oDetergent and softener only need to be added when required.
oThe operation time of the appliance will change according to the
water temperature, water level, amount of clothes, inlet water
pressure and drain state.
15

Wash program guidance
oA wash program option, such as Economy or Easy-Iron can only be
selected if the program table advises that it is possible with the
wash cycle you have selected (see page 10 or 15 for details)
oImportant: You should make sure that the selected spin speed is
appropriate for the garments that you are washing.
oThe active phases will be shown on the control panel as
the wash program progresses.
oPlease note that factors external to the machine, e.g. the
temperature of your water supply, your water pressure, water
hardness, external temperature etc., can affect the time it takes for
a wash cycle to complete.
Selecting a wash program
Setting a wash program
oUse the washing program selection dial (4) to select the required
program.
oIf you wish to add an additional function, such as an extra rinse to
the cycle, press the relevant function button (1).
oOnce the desired program has been selected, press the start /
pause button (3) to begin the wash cycle.
End of cycle
oWhen the wash cycle ends an audible signal will sound.
oThe door will unlock 2 minutes after the wash cycle has finished.
NOTE: The door will remain locked if the temperature inside the
drum is above 53°, or if there is too much water in the drum.
oRotate the program selection dial (4) to the OFF position (“O”).
oDisconnect the appliance from the electricity supply.
16

Pausing a wash program
oIf you want to pause a wash program temporarily, you should
press the start/pause button (3).
oWhen you want to restart the wash cycle, press the start/pause
(3) button again.
Delay start feature
Your appliance has a delay start feature, which allows you to delay the
start of a wash cycle until a later time.
1) Use the program selection dial (4) to select the desired cycle.
2) Add any desired optional extras by pressing the relevant function
button (1).
3) Once the required cycle has been set, press the
delay start button (2). Repeatedly press this
button to set the length of time which you wish to
pass before the washing cycle begins.
(3, 6 or 12 hours).
4) Press the start / pause button (2) and the
machine will enter standby mode. The cycle will
automatically begin when the delay start time is
reached.
Manual soaking
1) Load the laundry into the washing machine drum
2) Put the detergent into the drawer according to the
manufacturer’s instructions.
3) Use the program selection dial (4) to select the required wash
cycle. Press the start / pause button (3) to begin the cycle.
4) After approximately 10 minutes have passed, press the start /
pause button (3) again to pause the cycle. The clothes are then
able to soak in the water for your chosen length of time. Press
the start / pause button (3) to continue the wash cycle.
17

Easy-Iron function
oThe Easy-Iron function means that the machine will not execute
the last drain of the wash cycle – until the start/pause button is
pressed.
oThis means that the laundry will sit in the water until you are
ready to remove it for drying, preventing it from developing
creases.
NOTE: The maximum running time of this function is 12 hours.
After this time the machine will drain and spin automatically.
Extra rinse
oThe extra rinse option is mainly used for underwear or for the
clothes of people with sensitive skin. The laundry will undergo an
additional rinse to remove more residues of detergent.
oTo program an extra rinse, press the Rinse+ function button (1)
after you have selected a wash program (4) but before starting
the wash cycle by pressing start (3).
Child lock
Your appliance has a child lock option. When set, it will mean that the
control panel will be “locked”, and no buttons/selections will be
operational.
oPress and hold the rinse+ button (1) and the delay start button (2)
for 3-4 seconds to lock all controls on the control panel. There will
be an audible signal to confirm activation.
oThis will prevent accidental operation by unauthorised persons such
as children.
oTo deactivate the child-lock, press and hold the Rinse+ and Delay
start button again for 3-4 seconds.
oWhen locking or unlocking there will be an audible signal.
Power off memory
oYou do not need to do anything if the power supply to the machine
is cut off in the middle of a cycle.
oThe appliance will continue the wash when the power is turned on
again.
IMPORTANT: Please do not open the door by force when the
power is off.
18

Maintenance and cleaning
In daily use
oOnce a wash cycle has completed, you should pull out the
detergent drawer slightly, so it can dry out.
oLeave the porthole door ajar for a short while after a wash cycle
has completed. This should help to prevent stagnant smells and
to protect the door seal.
oAfter each washing program has finished, wipe up the remaining
water on the rubber seal ring and seal fold to prevent any
mildew and rot.
oClose the water tap.
oWe suggest that you disconnect the appliance from your mains
supply, when it is not in use.
Control panel and washing machine cabinet.
IMPORTANT: Do not use any abrasive cleaner or household polish on
either the control panel or operating parts.
oWipe over the control panel and the external surface of the
machine using a brand new damp cloth with warm water.
oIf you ever spill any liquid detergent or conditioner from the
detergent drawer onto the washing machine cabinet, then these
should be cleaned up immediately as they could be corrosive.
Detergent drawer
Occasionally the detergent drawer should be cleaned, to remove any
detergent residue that has built up.
oPull out the detergent drawer
until you feel resistance.
oPress the release catch and pull
out the drawer at the same time
to remove from the machine.
19

oDetergent can also accumulate
inside the detergent drawer
recess, so you should also clean
this out using warm soapy water
and a soft cloth.
oOnce you have finished cleaning
the detergent drawer and recess,
you should slide the drawer back
into its original position.
The washing machine drum
The drum of your washing machine is constructed from stainless steel.
However if objects that can rust are placed inside the drum, then it is
possible for the drum to become stained.
oWe would recommend cleaning the drum by running the “Anti-
Bac” (anti-bacterial) wash cycle approximately once every 3
months. Add a little detergent but DO NOT add laundry when
cleaning using this cycle.
IMPORTANT: Do not use a descaling agent, iron/steel wool or
scouring agents to clean the drum of your appliance.
oRemove any rust stains on the drum with an appropriate
stainless steel cleaning agent.
Door
oYou should regularly check to see if any deposits have formed,
or there are any foreign bodies inside or underneath the rubber
door gasket. This sits inside the opening of the porthole door.
20