Baxton Studio Connell LOR-003-Natural/Black User manual

A
B
C
30 PCS
30 PCS
2 PCS
1
2
D6 PCS
E48 PCS
F
G
16 PCS
2 PCS
H2 PCS
I2 PCS
L1 PCS
M1 PCS
N2 PCS
8 PCS
8 PCS
4 PCS
26 PCS
5 PCS
4 PCS
O
P
Q
R
S
T
2
1
3
4
5
5
6
7
8
9
x 4
10
10
11
12
13
15
14
16
J
K
2 PCS
2 PCS
LD RD CRCL
D
C
L
1
79
S
On piece 1, secure the catch (L) using screws (C). Use the pre-drilled
holes for guidance.
Attach piece 7 to piece 9 using screw (D), insert hardware parts (S) into piece 9.

3
5
4
6
M
Q
O
P
N
x4
K
K
12 16
2
3
E
E
E
E
E
E
E
T
CL
T
CL
T
CL
E
T
T
T
T
T
CL
CR
CR
CR
E
CR
D
3
8
R
R
R
R
7
R
A
B
3
5
5
6
DD
8
On pieces 12 attach the door handles (Q) using screws (O & P).
On pieces 16 attach the door handles (M) using screws (N), attach
bar hinges (K).
Attach the runners T to pieces 2 and 3 as shown. Use screws (E).
Attach piece 3 to piece 8 using wooden dowels (R), screw (D). Attach section to piece 5 6 & 7 using wooden dowels (R),
screw (D), cam dowels (A) and cam locks (B).

7
9 10
8
R
R
R
R
R
A
A
A
A
A
B
B
BB
6
5
5
B
8
7
2
4
R
A
A
2
4
3
A
A
A
A
A
A
B
BB
B
B
B
R
R
R
16
10
10
1
F
F
11
13
14
x4 x4
A
A
B
B
B
B
12
15
11
13
14
Then attach piece 2 & 4 using wooden dowels (R),cam dowels
(A) and cam locks (B).
Attach pieces 11, 13 & 14 using screws (F). Make sure that the built-in
ridge is facing inwards and at the bottom.
Slot in piece 10 to the built-in ridges, then add piece 1 to the unit using
wooden dowels (R), cam dowels (A) and cam locks (B). Connect door
16 using bar hinges (G).
Slot piece 15 into the ridges. First insert the cam locks (B) into the
pre-drilled holes on parts 13 & 14.Then insert cam dowels(A) into
each side, you then need to line up these screws with the pre-drilled
holes on the front piece (12). Once attached, tighten the cam locks (B)
using a cross-head screwdriver and ensure the piece is secure.

11
13 14
12
x4
E
E
12
15
T
T
DR
DL
1
12
12
12
12
S
S
1
J
H
G
I
I
1
G
Turn the drawer upside down. Line up the holes on the outside pieces
with the holes on the runners (TDR & TDL), secure to the drawer using
screws (E).
Attach strip (J) using screw (H).
Insert the drawers, insert hardware parts (S) into bottom of piece 2 & 4.
Secure the unit to a wall in your chosen location using
wall plugs (I) and screws (G).