Bayer HealthCare CONTOUR User manual

BLOOD GLUCOSE MONITORING SYSTEM
QUICK REFERENCE GUIDE
Basic Testing See your CONTOUR®User Guide and MICROLET ®2insert for complete instructions.
Remove the endcap
from the MICROLET®2
lancing device.
In one hand, hold the
lancing device with
your thumb on the
grip indent, and with
your other hand, hold
the gray endcap dial as shown. Gently snap
off the endcap.
Place the round
protective lancet cap
on a flat surface with
the Bayer logo facing
down.
With the used lancet
still in the lancing
device, push the
lancet needle completely into the middle of the
exposed side of the cap.
Eject the lancet following the instructions in
your lancing device insert.
Getting Ready to Test: Removing the used lancet:
Loosen the round pro-
tective cap on a lancet
by rotating it ¼ turn,
but do not remove it.
Insert the lancet firmly
to cock the device.
Twist off the lancet cap.
Replace the endcap.
Up/Down
Scroll
Buttons
Getting the Blood Drop:
Press the endcap
firmly against the
puncture site and
press the blue
release button with
your thumb.
Stroke your hand and finger towards the punc-
ture site to form a drop of blood.
Touch the tip of the
test strip to the drop
of blood. The blood
is pulled into the test
strip.
Hold it in the blood
drop until the
meter beeps.
Your result* is
displayed after a 5
second countdown.
To turn your meter off,
remove the test strip.
*Your meter is preset and
locked to display results
in mmol/L. If your result is
in mg/dL, contact Bayer
Diabetes Care Helpline
1-800-268-7200.
Insert the gray end of
the test strip into test
strip port on the meter.
No coding is required.
The meter will turn on
and a test strip with a flashing blood drop will
appear on your meter display letting you know
the meter is ready to test.
Adjust the endcap dial
to your preferred punc-
ture depth setting.
Your CONTOUR®Meter:
Your CONTOUR®Test Strip:
Gray End:
Insert this end
into the test
strip port.
Sample Tip:
Blood sample
pulled in here.
Test Strip
Port
Display
Memory
Button
(On/Off,
Memory
Recall,
Enter)
Testing Your Blood:
Fingertip Testing
Need Help?
Bayer Diabetes Care Helpline: 1-800-268-7200
www.bayerdiabetes.ca

After you perform a test and see your results on the display:
TO MARK RESULTS YOU WILL SEE TO SET YOU WILL SEE WHAT IT MEANS USING THE ALARM
Pre-Meal
Press ▲or ▼(Flashing) Press M
Result is marked
as a pre-meal test.
Press Magain to
set an alarm.**
When the alarm sounds, the
meter turns on, and you will
see your pre-meal test result.
Press any button once to
silence alarm and twice to
turn the meter off.
Run another blood test and
mark it with a post-meal
marker (see chart at left).
Post-Meal
Press ▲or ▼(Flashing) Press MResult is marked as
a post-meal test.
Logbook
Press ▲or ▼(Flashing) Press M
Result is marked in
memory as unique.
You should note this
in your Logbook.
Setting Your Meter to
Advanced Mode
To set your meter to Advanced Mode, and take
advantage of meal markers and other available
features:
1. Press Mto turn your meter on.
2. Press and hold ▲ or ▼ for 3 seconds.
3. L-1 will flash.
4. Press ▲ or ▼ to change
to L-2.
5. Press Mto set.
Using the Markers
See your User Guide for complete
instructions.
Using Advanced Mode See your User Guide for complete instructions. Error Codes and Symbols
E1
Temperature out of range.
E2
There was a problem
completely filling the test strip.
Retest using a new test strip.
E3
The meter is sensing a used
test strip.
Retest using a new test strip.
E11 Abnormal result.
Retest using a new test strip.
Bayer, Bayer Cross are registered trademarks of
Bayer AG used under license by Bayer Inc.
50184411
Rev. 5/08
Distributed by:
Bayer Inc.
Toronto, Ontario
M9W 1G6 Canada
See your User Guide for a complete list of
Error Codes.
Pre-meal =
Marks a test
result that was
taken before a
meal.
Post-meal =
Marks a test
result that was
taken after a
meal.
Logbook =
Marks any result
as being unique or different in some
way.
Alarm = Sets an alarm to remind you to
run a post-meal test.
Find out how these additional features can
help you manage your diabetes. Go to
www.bayerdiabetes.ca
or call Bayer Diabetes Care Helpline:
1-800-268-7200
**
Alarm is factory set at 2 hours. See User Guide for complete instructions on how to adjust alarm times.