BDH Elkay 370B-1 Manual

The Standard PIR Timer (3 wire)
is part of the Elkay family of switches,
timers and detectors which save
energy and increase convenience in
and around your home, garden
or premises.
Rating at 240V ac 50Hz
• Time Delay: 2 min - 1 hour
• All general load types 10A - Including
lighting loads that are LED, Compact
Fluorescent, Incandescent and Resistive
• This switch can also switch contactors
provided a capacitor is tted across
the coil
Fitting and Operating Instructions
1. Prior to tting ensure mains power is
switched OFF and Live In, Switch Live and
neutral wires are identied. Also where
applicable remove metal back box lugs
that are not being used.
2.For installation purposes, set the dip
switches for test mode as shown in
Timing Diagram and gently rotate the lux
pot anti-clockwise towards the plus (+).
3. Securely t Live In, Live Out and Neutral
into the terminals marked Lin, Lout & N.
4. Turn mains power ON.
5. To test the PIR timer leave the area and
the load will switch OFF in approximately
60 seconds as long as no movement or
external sources are detected.
6. To test the timer re-enter the area and the
PIR Timer will detect movement and
trigger the load ON.
7. Select time delay required using Timing
Diagram and the lux level pot to desired
ambient light level required.
8. Ensure the timer is secured to the back box
securely. Do not press the PIR dome for
any reason.
9. A capacitor (PFCC-1) may be required when
switching low wattage or some LED lighting.
–
STANDARD
PIR TIMER
370B-1
3 wire
Instruction Guide
BROOK DESIGN HARDWARE LTD
BDH
BDH
BROOK DESIGN
HARDWARE LTD
BDHBROOK DESIGN
HARDWARE LTD
BDH
BROOK DESIGN
HARDWARE LTD
BDH

Brook House,
Dunmurry Industrial Estate,
Dunmurry,
Belfast BT17 9HU
T [phone]
F [phone]
E [e-mail] elkay.co.uk
BROOK DESIGN HARDWARE LTD
BDH
B
DH
BROOK DESIGN
HARDWARE LTD
BDHBROOK DESIGN
HARDWARE LTD
BDH
BROOK DESIGN
HARDWARE LTD
BDH
Problem Resolution
Lights will not
switch OFF
• Check time settings (Black bar denotes position of dip switches).
• Check Connections.
• PIR is too close to lights – Re-position away from lighting, forced air ventilation or heating sources.
• Ensure PIR is not looking directly at heat source or is in direct sunlight.
• PIR is re-triggered – Check area is left unoccupied for longer than time setting using an accurate time piece.
• Capacitor must be tted if switching low wattage loads, LEDs or tted at coil if switching contactors.
Lights will not
switch ON
• Check Terminal connections.
• Lux set too low – Turn up lux level towards the plus and wait 30 seconds for sensor to adjust.
• In the unlikely event that the above does not work then press the reset button at the back.
(In circuits with multiple PIRs ensure that all PIRs have reset buttons pressed).
Light switches
OFF then
immediately
comes back ON
• Check terminal connections.
• PIR may be detecting normally  nd potential source that is triggering PIR. Best method is to cover
detector with thick material to eliminate potential trigger source.
• PIR is seeing infra-red heat from lighting load.
• Capacitor must be  tted if switching low wattage loads, LEDs or  tted at coil if switching contactors.
Diagram 1 – Time settings
Please note: The black bar denotes the position of the dip switch.
10-15 sec 2 mins 3 mins 4 mins 5 mins 7 mins 10 mins 15 mins
TEST MODE
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
20 mins 25 mins 30 mins 35 mins 40 mins 45 mins 50 mins 60 mins
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
LIVE IN
LIVE OUT
NEUTRAL
SL L SL LN
LIVE IN
LIVE OUT
NEUTRAL
SL L
LIVE IN
LIVE OUT
NEUTRAL
SL LN
NSLL
5 - 7m
4 - 6m
5 - 7m
3 - 4m
SL L
5 - 7m
4 - 6m
5 - 7m
3 - 4m
LIVE IN
LIVE OUT
NEUTRAL
SL L SL LN N
LIVE IN
LIVE OUT
NEUTRAL
SL L SL LN
LIVE IN
LIVE OUT
NEUTRAL
SL L
LIVE IN
LIVE OUT
NEUTRAL
SL LN
NSLL
5 - 7m
4 - 6m
5 - 7m
3 - 4m
SL L
5 - 7m
4 - 6m
5 - 7m
3 - 4m
LIVE IN
LIVE OUT
NEUTRAL
SL L
SL L
N
N
LIVE IN
LIVE OUT
NEUTRAL
SL L SL LN
LIVE IN
LIVE OUT
NEUTRAL
SL L
LIVE IN
LIVE OUT
NEUTRAL
SL LN
NSLL
5 - 7m
4 - 6m
5 - 7m
3 - 4m
SL L
5 - 7m
4 - 6m
5 - 7m
3 - 4m
LIVE IN
LIVE OUT
NEUTRAL
SL L
SL L
N
N
Diagram 2 – Wiring
Troubleshooting
Diagram 3 – Detection 360O
4-6m
3-4m
5-7m
Multiple switchingSingle switching
Important Notice
All wiring should be carried out by a competent person
or a qualifi ed electrician and should be fi tted to current
IEE wiring regulations BS 7671. The circuit should be
isolated before carrying out any work. Failure to adhere
to the instructions will invalidate the warranty.
Technical Helpline
For further help, or information on this and the other products in the Elkay range
go to www.elkay.co.uk or call [phone]. These instructions are
available in other languages. Please refer to our website www.elkay.co.uk
Instrukcje są również dostępne w innych językach. Prosimy o zapoznanie się z
naszą stroną internetową www.elkay.co.uk lub www.elkaypolska.pl
Elkay (Europe), 51C Milicka, Trzebnica, 55-100, Poland