BDH Elkay 376B-1 Manual

BROOK DESIGN HARDWARE LTD
BDH
BDH
BROOK DESIGN
HARDWARE LTD
BDHBROOK DESIGN
HARDWARE LTD
BDH
BROOK DESIGN
HARDWARE LTD
BDH
The Standard PIR Timer (2 wire)
is part of the Elkay family of switches,
timers and detectors which save
energy and increase convenience in
and around your home, garden
or premises.
Rating at 240V ac 50Hz
• Time Delay: 2 min - 1 hour
• 10A All lighting load types only - Including
lighting loads that are LED, Compact
Fluorescent, Incandescent and Resistive
• This switch cannot be used on
contactors
Fitting and Operating Instructions
1. Prior to tting ensure mains power is
switched OFF and Live In and Switch Live
are identied. Also where applicable
remove metal back box lugs that are
not being used.
2.For installation purposes, set the dip
switches for test mode as shown in
Timing Diagram and gently rotate the lux
pot anti-clockwise towards the plus (+).
3. Securely t Live In and Live Out into the
terminals marked Lin and Lout.
4. Press Reset Button on each PIR in
the circuit.
5. Turn mains power ON. Wait for 1 minute
for PIR to initiate itself.
6. To test the PIR timer leave the area and
the load will switch OFF in approximately
60 seconds as long as no movement or
external sources are detected.
7. To test the timer re-enter the area and the
PIR Timer will detect movement and
trigger the load ON.
8. Reset the desired time delay with
reference to timing diagram and the lux
level pot to desired ambient light
level required.
9. Ensure the timer is secured to the back box
securely. Note: Ensure no cables rest
on Reset button when switch is attached
to wall. Do not press the PIR dome for
any reason.
10. A capacitor (PFCC-1) will be required when
switching low wattage or some LED lighting.
–
STANDARD
PIR TIMER
376B-1
2 wire
Instruction Guide

Brook House,
Dunmurry Industrial Estate,
Dunmurry,
Belfast BT17 9HU
T [phone]
F [phone]
E [e-mail] elkay.co.uk
BROOK DESIGN HARDWARE LTD
BDH
B
DH
BROOK DESIGN
HARDWARE LTD
BDHBROOK DESIGN
HARDWARE LTD
BDH
BROOK DESIGN
HARDWARE LTD
BDH
Problem Resolution
Lights will not
switch OFF
• Check time settings (Black bar denotes position of dip switches).
• Check Connections.
• PIR is too close to lights – Re-position away from lighting, forced air ventilation or heating sources.
• Ensure PIR is not looking directly at heat source or is in direct sunlight.
• PIR is re-triggered – Check area is left unoccupied for longer than time setting using an accurate time piece.
• Capacitor must be tted if switching low wattage loads or LED lighting.
Lights will not
switch ON
• Check Terminal connections.
• Lux set too low – Turn up lux level towards the plus and wait 30 seconds for sensor to adjust.
• In the unlikely event that the above does not work then press the reset button at the back.
(In circuits with multiple PIRs ensure that all PIRs have reset buttons pressed).
Light switches
OFF then
immediately
comes back ON
• Check terminal connections.
• PIR may be detecting normally  nd potential source that is triggering PIR. Best method is to cover
detector with thick material to eliminate potential trigger source.
• PIR is seeing infra-red heat from lighting load.
• Capacitor must be  tted if switching low wattage loads or LED lighting.
Diagram 1 – Time settings
Please note: The black bar denotes the position of the dip switch.
10-15 sec 2 mins 3 mins 4 mins 5 mins 7 mins 10 mins 15 mins
TEST MODE
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
20 mins 25 mins 30 mins 35 mins 40 mins 45 mins 50 mins 60 mins
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
Diagram 2 – Wiring
Troubleshooting
Diagram 3 – Detection 360O
4-6m
3-4m
5-7m
Multiple switchingSingle switching
Note
Ensure no cables rest
on Reset Button
when switch is attached
to wall.
Important Notice
All wiring should be carried out by a competent
person or a qualifi ed electrician and should be
fi tted to current IEE wiring regulations BS 7671.
The circuit should be isolated before carrying out
any work. Failure to adhere to the instructions
will invalidate the warranty.
Technical Helpline
For further help, or information on this and the other products in the Elkay range go to
www.elkay.co.uk or call [phone]. In the unlikely event that you have to
return your product, please ensure you switch the battery off fi rst. These instructions
are available in other languages. Please refer to our website www.elkay.co.uk
Instrukcje są również dostępne w innych językach. Prosimy o zapoznanie się z naszą
stroną internetową www.elkay.co.uk lub www.elkaypolska.pl
Elkay (Europe), 51C Milicka, Trzebnica, 55-100, Poland