BDH Elkay 380A-1 Manual

The Microwave Timer (3 wire) is part of
the Elkay family of switches, timers and
detectors which save energy and increase
convenience in and around your home,
garden or premises.
Rating at 240V ac
• Time Delay: 2 min - 2 hrs
• All general load types 16A - Including
lighting loads that are LED, Compact
Fluorescent, Incandescent and Resistive
• Lux level / Daylight adjustment
• Sensitivity Adjustment
• 15 to 30 metres range
Fitting and Operating Instructions
1. Ensure the mains power is switched o before
any wiring takes place.
2. Fit the back box to the wall for mounting using
appropriate screws and xings
(not supplied).
3. Set the dip switches to the required time
settings (See diagram 2).
4. Connect the Live In, Live Out (Switch Live) and
the Neutral into the marked terminals
(See diagram 1).
5. To adjust lux level, locate lux level adjuster on
the circuit board where the word LUX is printed.
Turn anticlockwise for plus (+)and clockwise
for minus (–).
6. To adjust sensitivity, locate SEN on the opposite
side of the circuit board turn clockwise for plus
(+)and anticlockwise for minus (–).
7. Please ensure white faceplate is attached before
initialisation with holes at the top (See diagram 1).
8. Apply the mains power. Your load will turn on and
a red light will begin ashing for 2 minutes and
then will ash rapidly for 1 minute. At the end of
this 3 minute cycle the load will turn o. The load
will switch on again once further movements
are detected.
9. Please note the red LED should be clearly seen
through the hole in the faceplate. The unit is
supplied with the default setting of max lux and
sensitivity levels.
N.B. For ush mounting please ensure that it ts
into a 35mm backbox.
Corridor / Oce Plan A
When using PIRs in long corridors or spaces, there is
often a need to position them every 6 to 8 metres
(See diagram 4). This incurs additional cabling, labour
and connection costs at install. Maintenance costs
over time are also increased from a PPM perspective
as there are more devices to check and maintain.
Corridor / Oce Plan B
With the Elkay Microwave detector 380A-1 mounted
on the wall only one device is needed to cover areas
up to 30 metres with lateral cover provided for up
to 8 metres which increases overall exibility
(See diagram 5). Microwave Detectors reduce cabling,
connection, labour and future PPM costs simply
because fewer detectors are needed. They can be
mounted from 1.2 to 2.5m in height and should
be wall mounted for best eect. They can also be
used in hi bay lamps that are PL types or hot
re-strike luminaires.
–
MICROWAVE
TIMER
380A-1
3 wire
Instruction Guide
BROOK DESIGN HARDWARE LTD
BDH
BDH
BROOK DESIGN
HARDWARE LTD
BDHBROOK DESIGN
HARDWARE LTD
BDH
BROOK DESIGN
HARDWARE LTD
BDH

2 mins 5 mins 10 mins 15 mins 20 mins 25 mins 30 mins 40 mins
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
50 mins 60 mins 70 mins 80 mins 90 mins 100 mins 110 mins 120 mins
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
Brook House,
Dunmurry Industrial Estate,
Dunmurry,
Belfast BT17 9HU
T [phone]
F [phone]
E [e-mail] elkay.co.uk
BROOK DESIGN HARDWARE LTD
BDH
B
DH
BROOK DESIGN
HARDWARE LTD
BDHBROOK DESIGN
HARDWARE LTD
BDH
BROOK DESIGN
HARDWARE LTD
BDH
Technical Helpline
For further help or assistance or information on this or other products in the range
please call the Elkay Technical team on [phone]. Please call the
Technical helpline before returning any products to your stockist. These instructions
are available in other languages. Please refer to our website www.elkay.co.uk
Instrukcje są również dostępne w innych językach. Prosimy o zapoznanie się z naszą
stroną internetową www.elkay.co.uk lub www.elkaypolska.pl
Important Notice
All wiring should be carried out by a competent
person or a qualifi ed electrician and should be
fi tted to current IEE wiring regulations BS 7671.
The circuit should be isolated before carrying out
any work. Failure to adhere to the instructions
will invalidate the warranty.
Elkay (Europe), 51C Milicka, Trzebnica, 55-100, Poland
2 mins 5 mins 10 mins 15 mins 20 mins 25 mins 30 mins 40 mins
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
50 mins 60 mins 70 mins 80 mins 90 mins 100 mins 110 mins 120 mins
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
Diagram 1
Wiring diagram for a three wire Microwave unit
(For additional products to be added see Diagram 3).
Wiring diagram for additional
microwave units.
Diagram 2 – Time settings
Please note: The black bar denotes the position of the dip switch.
* If faceplate is
clipped on the wrong
way Lux level
adjustment will not
work correctly
(See TOP markings).
Diagram 3
Plan view of Microwave pattern.
Diagram 4 - Corridor /
O ce Plan A
Diagram 5 - Corridor /
O ce Plan B