Beamz 150.568 User manual

Ref. Nr. 150.568
WI-PAR 198 LED RGB BATTERY
2.4GHZ DMX
MANUAL

- 2 -
Thank you for purchasing our company products.
Please read these instructions carefully to enjoy optimum performance and a longer service life before
you start to use.
CONTENTS
CONTENTS............................................................................................................................................. 2
Unpacking Inspections ............................................................................................................................ 3
Unpacking instructions ........................................................................................................................ 3
Checking the contents of the carton:................................................................................................... 3
Safety Instructions................................................................................................................................... 3
Product Overview.................................................................................................................................... 4
Functions Introductions ........................................................................................................................... 4
Main Functions .................................................................................................................................... 4
Operation Instructions ......................................................................................................................... 5
Power supply connecting：............................................................................................................. 5
Control panel operation................................................................................................................... 5
DMX Mode........................................................................................................................................... 6
Set DMX adres................................................................................................................................ 6
Act mode（Standalone) ...................................................................................................................... 8
IR control ............................................................................................................................................. 9
Automatic Mode............................................................................................................................... 9
Sound Active Mode ......................................................................................................................... 9
Manual Color Control....................................................................................................................... 9
DMX Mode Auto Sync....................................................................................................................... 10
For the transmitting product........................................................................................................... 10
For the receiving product(s)........................................................................................................... 10
DMX Mode Manual Sync:.................................................................................................................. 10
For the transmitting product........................................................................................................... 10
For the receiving product(s)........................................................................................................... 11
IR/standalone mode auto Sync ......................................................................................................... 11
For the transmitting product:.......................................................................................................... 11
For the receiving product(s)........................................................................................................... 11
Maintenance.......................................................................................................................................... 12
Specification .......................................................................................................................................... 12
CE & R&TTE Declaration of Conformity................................................................................................ 13

- 3 -
UNPACKING INSPECTIONS
Unpacking instructions
Please unpack the carton and check the goods carefully when you receive it , if discover
packing damage, shortage or quality problem, please notify the shipper and reject the goods.
Before using this product, please read the instructions carefully and keep it in a safe place for
future reference.
Checking the contents of the carton:
The product, Power cord, Instruction Manual, Remoter
SAFETY INSTRUCTIONS
Safety and regulatory power socket with high quality output should be used .
Always connect the product to a grounded circuit to avoid the risk of electrocution.
Never put tiny metal objects such as a screwdriver, iron wire and coins, etc. into the internal or
stretch into the machine in case of short circuit .
Please make sure to connect the proper voltage and do not higher or lower than that stated on
the decal or rear panel of the product .
Avoid hitting, crashing or squeezing with other objects in transportation. Never carry the
product from the power cord or any moving part . Always use the hanging / mounting bracket
or the handles.
The product is used in door only .
Never pull or tug on the cord and change it for another one , stop using it when it is damaged
or becomes hot .
Stop using the product once there is sparks when connecting with the power plug .
Can not operate product with wet hands and never place it near the water or other liquid.
Make sure there are no flammable materials close to the fixture while operating . Always install
it in a location with adequate ventilation.
Never replace the lighting source with different specification and rating when the original one
is damaged.
Make sure to power off before replacing the light source or the fuse. Never do it while it is on.
The ambient temperature is no more than 40°C(104°F) .
Never clean the fixture by water, thinner or other dissolved agent .
Stop using the product in case of a serious operating problem and send it to our maintenance
agent immediately. Never repair by non-professional workers .
Avoid direct eye exposure to the light source while the product is on.

- 4 -
PRODUCT OVERVIEW
1. Control Panel
2. Power on/off
3. Battery indicator
4. Microphone
5. Auto Search
6. Safety Eyebolt
7. Master/Slave signal output
8. DMX signal input
9. DMX signal output
10. Power input
11. Power output
12. Antenna
13. LEDs
FUNCTIONS INTRODUCTIONS
Main Functions
3 or 4 DMX channels
Automatic, sound active and master/slave mode
Built-in 23 actions, run speed and strobe speed can be adjusted
With static colors, strobe, dimmer, color mixing and changing effects
IR Remote control
Can receive and transmit signal wirelessly

- 5 -
Operation Instructions
Power supply connecting：
Two sockets in the product, Power In and Power Out , the product can be supplied power by the power out.
Maximum output power of the socket is 480W .
Control panel operation
Use the four buttons《MODE》《ENTER》《UP》and《DOWN》to operate the control panel:
SYS System settings
S-Ir IR control
ACT Action control, stand alone programs
SLAU Slave mode, set receive frequency for IR & ACT use
Press 《MODE》to find an operation mode or to back out of the current menu option.
Press 《UP》to scroll up the list of options or to find a higher value.
Press 《DOWN》to scroll down the list of options or to find a lower value.
Press 《ENTER》to activate a menu option or a selected value.
Maximum connecting machines are
22 units with the same model
POWER OUT
POWER IN

- 6 -
MODE Description
SYS
S dAd DMX address setup（001-509）
d-CH 3CH 3CH DMX mode
4CH 4CH DMX mode
s-tr
t.CH Manually select transmit frequency (for IR&Act use) t001-t016
tA.S Automatically select Receive frequency (for IR&Act use)
dt.CH Manually select Transmit frequency (for DMX use) dt01-t16
dtA.S Automatically select Transmit frequency (for DMX use)
dr.CH Manually select receive frequency (for DMX use) dr.01-dr.16
drA.S Automatically select receive frequency (for DMX use)
d-SL Sensitivity low to high (SL.00-SL.32)
S AAd Reset software
S-Ir IR Infrared remote control
SLAu rA.S r-AU Automatical select receive frequency (For IR&Act use)
r-St r001-r016 Manually select receive frequency (For IR&Act use) r001-r016
ACt A000 -
A023
F000-F100 Strobe speed (slow to fast )
SL.00-SL.32 Sensitivity low to high (SL.00-SL.32)
P000-P100 Run speed (slow to fast )
C000-C100 Brightness adjustment (dark to bright)
DMX Mode
Set DMX adres
When selecting a starting DMX address, always consider the number of DMX channels. If you choose a starting
address that is too high, you could restrict the access to some of the product’s channels. With 3Ch & 4CH, when in
4-channel DMX mode, it defines the highest configurable address 509.
Follow below to select the DMX starting address
Press <MODE> repeatedly until SYS,ACt,SLAv,or S-1r shows on the display.
Use <UP> or <DOWN> to select SYS.
Press <ENTER>
Use <UP> or <DOWN> to select SdAd from the menu
Press <ENTER>
Use <UP> or <DOWN> to select the starting address.
Press <ENTER>
With 3CH and 4CH,follow below to setup
Press <MODE> repeatedly until SYS, ACt, SLAv, or S-1r shows on the display.
Use <UP> or <DOWN> to select SYS
Press <ENTER>
Use <UP> or <DOWN> to select d-CH from the menu
Press <ENTER>
Use <UP> or <DOWN> to select either the 3-channel mode (3CH) or the 4-channel mode (4CH)
Press <ENTER>

- 7 -
DMX Value Functions 4 CH
CHANNEL VALUE FUNCTION CH 2 CH 3 CH 4
1
Static colors
Flash speed
000 – 249
Sound
Active
250 – 255
000 – 009 Blackout
010 – 019 Red
020 – 029 Green
030 – 039 Blue
040 – 049 Red + Green
050 – 059 Red + Blue
060 – 069 Blue + Green
070 – 079 Red + Green + Blue
Color Changes
Run Speed
Automatic
000 – 127
Sound Active
128 – 255
Flash speed
000 – 249
Sound
Active
250 – 255
080 – 089 Color change 1
090 – 099 Color change 2
100 – 109 Quadrant Effect 1
110 – 119 Quadrant Effect 2
120 – 129 Quadrant Effect 3
130 – 139 Quadrant Effect 4
140 – 149 Quadrant Effect 5
150 – 159 Quadrant Effect 6
160 – 169 Quadrant Effect 7
170 – 179 Quadrant Effect 8
180 – 189 Color change 3
190 – 199 Color change 4
200 – 209 Color change 5
210 – 219 RGB Color Mix mode Red
0-100% Green 0-100% Blue 0-100%
220 – 229 Color Mode Fade speed
0-100%
230 – 255 Auto Run (sound active only)
DMX Value Functions 3 CH
VALUE CH 1 CH 2 CH 3
000 – 255 RED GREEN BLUE

- 8 -
Act mode（Standalone)
Set the product in one of the standalone modes to control without connecting a DMX controller.
Note: Never connect a product that is operating in any standalone mode to a DMX string connected to a DMX
controller.
Follow below actions to setup standalone mode:
Press <MODE> repeatedly until SYS,ACt,SLAv,or S-1r shows on the display.
Use <UP> or <DOWN> to select Act
Press <ENTER>
Use <UP> or <DOWN> to choose your desired program (A000-A023).
Press <ENTER>
Note: Certain programs will have additional functionality. To find these options, press <ENTER> after selecting an
auto program. Then press <UP> or <DOWN>. Not every program will feature all the added functionality.
Function: F000 - F100 SL.00 – SL.32 P000 – P100 C000 – C1000
Description: Flash speed
(slow to fast) Sound sensitivity Run speed (slow to fast) Dimmer
Please refer to below:
Display Function Run Speed (P) Flash Speed (F) Color (C)
A000 Black 0 – 100
A001 Red 0 – 100
A002 Green 0 – 100
A003 Blue 0 – 100
A004 Yellow 0 – 100
A005 Purple 0 – 100
A006 Cyan 0 – 100
A007 White 0 – 100
A008 Color Change
Run Speed
Automatic
0 – 50
Run Speed
Sound
51 – 100
0 – 100
A009 Action 1 0 – 100
A010 Action 2 0 – 100
A011 Action 3 0 – 100
A012 Action 4
A013 Action 5
A014 Action 6
A015 Action 7
A016 Action 8
A017 Action 9
A018 Action 10
A019 Action 11
A020 Action 12
A021 Any Color 0 – 100 (red) 0 – 100 (green) 0 – 100 (blue)
A022 Color Fade 0 – 100
A023 Auto Run 0 – 100

- 9 -
IR control
It is fully compatible with the IRC (Infrared Remote Control),please follow below to setup.
Press <MODE> repeatedly until SYS, ACt, SLAv, or S-1r shows on the display.
Use <UP> or <DOWN> to select S-1r, Press <ENTER>, Begin using the IRC
The functions of IRC:
Automatic Mode
Automatic Mode will enable you to run the automatic programs on the product.
Press AUTO on the IRC. Press +
or - to choose different auto programs.
To adjust the speed of the automatic program. Press
SPEED on the IRC Press +
or - to either increase or decrease the speed of the program.
Sound Active Mode Sound
Active Mode will enable the product to respond to music and follow below
actions. Press
sound button.
Adjust the sound sensitivity. Press
sensitivity button. Press +
or - to either increase or decrease sound sensitivity.
Manual Color Control.
To choose a specific color with the IRC.
Press MANUAL on the IRC.
Press any number between 0-9 to choose your color.
To manually control the RGB percentage.
Press MANUAL on the IRC.
Press R, G, or B to choose your color.
Press the number (percentage) you desired
Press the button of %.
For example:
[MANUAL] -> [R] -> [5] -> [0] -> [%], red changes as 50%.
strobe control.
Follow below actions.
Press the strobe button on the IRC, Use + o - to adjust strobe speed.
Fade/snap.
Press the button of Fade/snap, Use + or - to adjust speed.
BLACK OUT.
Use the button of BLACK OUT to turn on or turn off.
Press the BLACK OUT to turn off.
Press Auto button to turn on and press BLACK OUT to turn on or turn off with power of the product.

- 10 -
DMX Mode Auto Sync
It offers wireless control of two or more products with a single DMX controller. To set syncing function for DMX
functionality automatically, do the following:
For the transmitting product.
Press <MODE> repeatedly until SYS, ACt, SLAv, or S-1r shows on the display.
Use <UP> or <DOWN> to select SYS.
Press <ENTER>.
Press <UP> or <DOWN> until S-tr appears on the display.
Press <ENTER>.
Press <UP> or <DOWN> until dtA.S appears on the display.
Press <ENTER>.
The display should show dt.AU.
For the receiving product(s).
Press <MODE> repeatedly until SYS, ACt, SLAv or S-1r shows on the display.
Use <UP> or <DOWN> to select SYS.
Press <ENTER>.
Press <UP> or <DOWN> until S-tr appears on the display.
Press <ENTER>.
Press <UP> or <DOWN> until dRA.S appears on the display.
Press <ENTER>.
The display should show dR.AU.
Once the steps above are done, press and hold <AUTO> on the transmitter for about 20 seconds and the signal
LED of receiver will flash to indicate sync is activated.
Cancel Auto Sync.
Press the Auto button of the receiving product until the signal stops flash, which means the between the receiver
and transmitter is cancelled.
Auto Sync for receivers and transmitters:
Repeat operations, match the next group after finishing matching the first group. (Power off other fixtures when you
follow the actions and multiple groups can not be matched at the same time)
One transmitter to multiple receivers.
Follow the instructions and set one as transmitter, the others as receivers, set the auto Sync between one receiver
and one transmitter, and then power off the receiver, match another pair. Power on all the receivers after finishing,
multiple receivers can be controlled by one transmitter.
DMX Mode Manual Sync:
It can wireless control of two or more products with a single DMX controller. To manually set up the syncing function
for DMX functionality, do the following.
For the transmitting product.
Press <MODE> repeatedly until SYS,ACt,SLAv,or S-1r shows on the display.
Use <UP> or <DOWN> to select SYS.
Press <ENTER>.
Press <UP> or <DOWN> until S-tr appears on the display.
Press <ENTER>.
Press <UP> or <DOWN> until dt.CH appears on the display.
PRESS <ENTER>.
Use <UP> or <DOWN> to select the transmitting signal (dt.01-dt.16).