Beamz MHL-45 User manual

Ref. No.: 150.520
MHL-45 DMX Mini Moving Head
Wash
3X 15W COB LED DMX
MANUAL

Table of contents
Unpacking ……………………………………………………….………………………….3
SAFETY INSTRUCTIONS…………………………………………………………………3
SPECIFICATIONS…………………………………………………………………………..4
INSTALLATION………………………………………………………………….…………..4
OPERATION……………………………………………………………………….………...5
Stand alone operation…………………………………………………………….…………5
Master slave operation…………………………………………………………….……..…5
DMX controlled operation………………………………………………………….…….…5
Addressing…………………………………………………………………………….…..…6
Control board………………………………………………………………………….…..…6
DMX protocol………………………………………………………………………….…..…7
CE Declaration ……………………………………………………………………….……8

UNPACKING INSPECTIONS
Unpacking instructions
Please unpack the carton and check the goods carefully when you receive it , if discover
packing damage, shortage or quality problem, please notify the shipper and reject the goods.
Before using this product, please read the instructions carefully and keep it in a safe place for
future reference.
Safety Instructions
Safety and regulatory power socket with high quality output should be used .
Always connect the product to a grounded circuit to avoid the risk of electrocution.
Never put tiny metal objects such as a screwdriver, iron wire and coins, etc. into the internal or
stretch into the machine in case of short circuit .
Please make sure to connect the proper voltage and do not higher or lower than that stated on
the decal or rear panel of the product .
Avoid hitting, crashing or squeezing with other objects in transportation. Never carry the product
from the power cord or any moving part . Always use the hanging / mounting bracket or the
handles.
Never pull or tug on the cord and change it for another one , stop using it when it is damaged or
becomes hot .
Stop using the product once there is sparks when connecting with the power plug .
Make sure there are no flammable materials close to the fixture while operating . Always install
it in a location with adequate ventilation.
Never replace the lighting source with different specification and rating when the original one is
damaged.
Make sure to power off before replacing the light source or the fuse. Never do it while it is on.
The ambient temperature is no more than 40°C(104°F) .
Never clean the fixture by water, thinner or other dissolved agent .
Stop using the product in case of a serious operating problem and send it to our maintenance
agent immediately. Never repair by non-professional workers .
Avoid direct eye exposure to the light source while the product is on.
SPECIFICATION
TECHNICIAL SPECIFICATIONS
Model C315 COB moving wash
Voltage 110V- 250V / 50-60Hz
Power consumption: 65W
LED 3pcsX15w RGB 3 in 1 COB LEDs
Gross Weight 3.5Kgs
Features
11 channel DMX-512 .
Pan :630°/tilt:180°.
Variable electronic strobe.
Variable electronic dimmer(0-100%).
LED display menu with invert.
Reset to factory settings option.
Pan/tilt invert option.
Fan cooled.

Dimensions 28(H) x 22(W) x 27(L) mm
INSTALLATION
Rigging
The installation of the projector has to be built and constructed in a way that it can hold 10 times the
weight for 1 hour without any harming deformation.
IMPORTANT!OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including calculating
working load limits, installation material being used, and periodic safety inspection of all installation
material and the projector. If you lack these qualifications, do not attempt the installation yourself, but
instead use a professional structural rigger. Improper installation can result in bodily injury and or
damage to property. The projector had to be installed out of the reach of people
DANGER OF FIRE! When installing the device, make sure there is no highly-inflammable
material(decoration articles, etc.)within a distance of min.0.5m.
DMX 512 connection/ connection between fixture
The wires must not come into contact with each other, otherwise the fixture will not work at all or
properly. Please note the starting address depends upon which controller is being used. Only use a
DMX cable and 3-pin XLR-plugs and connectors in order to connect the controller with the fixture or one
fixture to another
Connection with the mains.
The earth has to be connected. The device must only be connected with an electric installation carried
out in compliance with IEC standards.

OPERATION
After you connected the effect to the mains, The fixture starts running
Stand Alone operation
In the stand alone mode, the fixture can be use without controller
Master/slave-operation
The master/slave-operation enables that several devices can be synchronized and controlled by one
master-device
DMX controlled operation
You can control the projectors individually via your DMX-controller
Addressing
The control board allows you to assign the DMX starting address,
Note;it’s necessary to insert the XLR termination plug (with 120ohm) in the last device in the link in order
to ensure proper transmission on the DMX data link.
CONTROL BOARD
The control board offer several features :you can simple set the starting address, run the
pre-programmed program or make a reset
he main menu is accessed by pressing the Mode/Esc-button, Browse through the submenu by pressing
Up or Down .Press the Enter-button in order to select the desired menu. You can change the selection
by pressing Up or Down, Confirm every selection by pressing the Enter-button. You can leave every
mode by pressing the Mode/Esc-button .The functions provided are described in the following setting.
MENU MAP
The device has two operation modes, It can be operated in StandAlone or in DMX controlled
A001 (address code setting fromA001-------A512)
AU01(auto-moving speediness) AU02(slow speed auto-moving)
SN01(Sound control for color changing) SN02( Sound control for strobe)
RPOF(Set pan to forward-rotating) RPON(Set pan circumrotate reverse)
RTOF(Set tilt to forward-rotating) RTON(Set tilt circumrotate reverse)
RDOF(set the LED readout to non-inverting) RDON(Set the LED readout to inverting)
DFON (Default output setting)
Note：output default setting address code is A001, pan is positive circumrotate、tilt is positive
circumrotate、LED positively reveal.

User configurations
Setup single-desk light`s autocephaly moving mode(auto-running)
.Press the MENU until it shows AU01
.Use the UP/DOWN buttons to set to AU01 or AU02 ,Press ENTER to confirm.
Setup single-desk light`s autocephaly moving mode(sound control)
.Press the MENU button until it shows SNOF .
.Use the UP/DOWN buttons to set to SNOF,press ENTER to confirm.
Master/slave mode(auto-running、sound control)
.This mode will allow you to link up 32 units together without a controller.
.Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of
the units.Proper performance it may be necessary to use a terminator at the last fixture. For more
information about terminators..
Set the desired master-mode- “Automatic program mode” or”sound controlled mode”, for the
master-device, send the DMX address 1 for all slave-devices. Please refer to the instruction under
control board.
To set the pan to reverse
.Press the MENU until it shows RPOF.
.Use the UP/DOWN buttons show RPON, press ENTER to confirm.
To set the tilt to reverse
.Press the MENU until it shows RTOF
.Use the UP/DOWN buttons show RTON, press ENTER to confirm.
To set the LED readout to 180°,rotating
.Press the MENU until it shows RDOF.
.Use the UP/DOWN buttons show RDON, press ENTER to confirm.
Resume reverse Windows default
.Press the MENU until it shows DFON.
.press ENTER to confirm。

DMX-protocol
11 DMX channel mode
Channel Value Function
1
0-255 Pan Pan movement 0~630
2
0-255 Tilt Tilt movement 0~180
3
0-255 Pan Tilt speed Pan & Tilt speed adjustment
4
0-255 Red 0-100% Red
5
0-255 Green 0-100% Green
6
0-255 Blue 0-100% Blue
7
0-40
41-80
81-120
121-140
141-160
161-200
201-255
Color Change
Neutral
Red
Green
Blue
Green/Blue
Green
Red/Blue
8
0-10
11-20
21-30
31-200
201-250
251-255
Switching the LEDs/Strobe/Reset
LED OFF
Neutral
Reset
Strobe-effect with increasing speed
Random strobe-effect with increasing speed
Neutral
9
0-255 Dimmer 0-100% Dimmer
10
0-255 Pan Fine Pan fine
11
0-255 Tilt Fine Pan fine
0-40, no function, 41-80,red. 81-120,red/blue. 121-140,blue.
141-160,green/blue.161-200,green. 201-255, red/green


CE Declaration of Conformity
Importer: TRONIOSBV
Bedrijvenpark Twente 415
7602 KM - ALMELO
Tel : [phone]
Fax : [phone]
The Netherlands
Product number: 150.520
Product Description: MHL-45 Wash 3x15W COB LED DMX
Regulatory Requirement: EN 60598-1/-2-17
EN 55015
EN 61547
EN 61000-3-2/-3-3
EN 300 440-1/-2
The product meets the requirements stated in the above mentioned Standards.
13-12-2012
Signature :