Beamz MHL-715WiSpot 7x 15W QUAD DMX 2.4Ghz User manual

- 1 -
Ref. No.: 150.527
MHL-715WISPOT 7X 15W QUAD
DMX 2.4GHZ
MANUAL

- 2 -
Thank you for purchasing our company products.
Please read these instructions carefully to enjoy optimum performance and a longer service life before
you start to use.
UNPACKING INSPECTIONS
Unpacking instructions
Please unpack the carton and check the goods carefully when you receive it , if discover
packing damage, shortage or quality problem, please notify the shipper and reject the goods.
Before using this product, please read the instructions carefully and keep it in a safe place for
future reference.
Checking the contents of the carton:
The product, Power cord, Instruction Manual, Mounting Bracket

- 3 -
Safety Instructions
Safety and regulatory power socket with high quality output should be used .
Always connect the product to a grounded circuit to avoid the risk of electrocution.
Never put tiny metal objects such as a screwdriver, iron wire and coins, etc. into the internal or
stretch into the machine in case of short circuit .
Please make sure to connect the proper voltage and do not higher or lower than that stated on
the decal or rear panel of the product .
Avoid hitting, crashing or squeezing with other objects in transportation. Never carry the
product from the power cord or any moving part . Always use the hanging / mounting bracket
or the handles.
The product is used in door only .
Never pull or tug on the cord and change it for another one , stop using it when it is damaged
or becomes hot .
Stop using the product once there is sparks when connecting with the power plug .
Can not operate product with wet hands and never place it near the water or other liquid.
Make sure there are no flammable materials close to the fixture while operating . Always install
it in a location with adequate ventilation.
Never replace the lighting source with different specification and rating when the original one
is damaged.
Make sure to power off before replacing the light source or the fuse. Never do it while it is on.
The ambient temperature is no more than 40°C(104°F) .
Never clean the fixture by water, thinner or other dissolved agent .
Stop using the product in case of a serious operating problem and send it to our maintenance
agent immediately. Never repair by non-professional workers .
Avoid direct eye exposure to the light source while the product is on.
PRODUCT OVERVIEW
FUNCTIONS INTRODUCTIONS
Main Functions
9 or 12 DMX channels .
Sound active, (wireless) DMX, master/slave mode .
7x 15W high quality QUAD LEDs.
With static colors, strobe, dimmer, color mixing and changing effects.
Pan/Tilt inversion
Electronic dimming 0 –100%

- 4 -
System menu

- 5 -
DMX Address –Set the DMX address
Press the UP or DOWN button until “DMX address” is displayed, press ENTER.
“X” will now be displayed, (“X” represents the displayed address). Press the UP or DOWN button to
find the desired address. Press ENTER to confirm
System Reset –Use this function to reset the fixture.
Press the UP and DOWN button until “System Reset” is displayed, press ENTER.
The fixture will reset.
Firmware Version –This will display the software version
Press the UP or DOWN button until “Firmware Version” is displayed, press ENTER.
The software version will be displayed.
Fixture Time –With this function you can display the running time of the fixture.
Press the UP or DOWN button until “Fixture Time” is displayed, press ENTER.
The running time of the fixture will be displayed.
White Balance –This menu will let you select your desired strobe mode
Press the MENU button and UP button or DOWN button until “White Balance”is displayed, press
ENTER.
Press ENTER to display the “red” “green” “blue” and then press ENTER, the “RXXX” “GXXX” “BXXX”
XXX is the value of red, green and blue, then press the UP or DOWN to adjust the value.
Auto Test –With this function you can manually test the individual features.
Press the UP and DOWN button until “AutoTest” is displayed, press ENTER.
Use the UP and DOWN button to find the function or colors that you wish to test.
Once you find a function or color you wish to test, Press the ENTER button. Now you can adjust the
values by pressing UP and DOWN buttons. Once you have finished testing, press the ENTER button.
Tilt Invert –Tilt Inversion
Press the UP and DOWN button until “Tilt Invert” is displayed, press ENTER.
To activate the Tilt inversion press the UP or DOWN buttons until “yes” is displayed, press ENTER to
confirm. To deactivate Tilt inversion, select “No” and Press ENTER.
PAN Invert –Tilt Inversion
Press the UP and DOWN button until “Pan Invert” is displayed, press ENTER.
To activate the Tilt inversion press the UP or DOWN buttons until “yes” is displayed, press ENTER to
confirm. To deactivate Tilt inversion, select “No” and Press ENTER.
Pan Angle –Pan Angle
Press the UP or DOWN button until “Pan Angle” is displayed, press ENTER.
Press the UP or DOWN buttons to set your rotation.

- 6 -
Back LCD –Back LCD
Press the UP or DOWN button until “Black LCD” is displayed, press ENTER.
Press the ON or OFF buttons to set your desired LCD mode.
Show Mode –In this mode you can select your desired master mode
Press the UP or DOWN button until “Show Mode” is displayed, press ENTER.
Press the UP or DOWN buttons to select your desired master mode.
Slave Mode –In this mode the fixture will be a slave
Press the UP or DOWN button until “Slave Mode” is displayed, press ENTER.
Press the UP or DOWN buttons to select Master or Slave mode.
Channel mode –Select the desired channel mode
Press the UP or DOWN button until “Channel mode” is displayed, press ENTER.
“X Ch” will now be displayed, “X” represents the displayed channel mode. Press the UP or DOWN
buttons to find the desired channel mode. Press ENTER to confirm.
Wireless DMX
Switch the wireless system on with the on/off switch on the back panel.
Press the wireless button on the front panel to connect the system with your wireless transmitter. After
the connection is linked the LED will flash faster.
To reset the wireless connection, press and hold the button until the LED stops flashing.

- 7 -
Operation Instructions
DMX connection.
Master / Slave
connection.

- 8 -
DMX Channel settings
12 Channel settings:
DMX 12 Channel
DMX
Description
1
Dimmer
001 - 255
Dimmer 0 –100%
2
Macro Color
000 –009
Unused
010 –014
Red
015 –019
Green
020 –024
Blue
025 –029
Macro Color 1
030 –034
Macro Color 2
035 - 038
Macro Color 3
039 –043
Macro Color 4
044 –048
Macro Color 5
049 –053
Macro Color 6
054 –058
Macro Color 7
059 –063
Macro Color 8
064 –067
Macro Color 9
068 –072
Macro Color 10
073 –077
Macro Color 11
078 –082
Macro Color 12
083 –087
Macro Color 13
088 –091
Macro Color 14
092 –096
Macro Color 15
097 –101
Macro Color 16
102 –106
Macro Color 17
107 - 111
Macro Color 18
112 –116
Macro Color 19
117 –120
Macro Color 20
121 –125
Macro Color 21
126 –130
Macro Color 22
131 –135
Macro Color 23
136 –140
Macro Color 24
141 –145
Macro Color 25
146 –149
Macro Color 26
150 –154
Macro Color 27
155 –159
Macro Color 28
160 –164
Macro Color 29
165 –169
Macro Color 30
170 –173
Macro Color 31
174 –178
Macro Color 32
179 –183
Macro Color 33
184 –188
Macro Color 34
189 –193
Macro Color 35
194 –198
Macro Color 36
199 –202
Macro Color 37
203 –207
Macro Color 38
208 –212
Macro Color 39

- 9 -
213 –217
Macro Color 40
218 –222
Macro Color 41
223 –227
Macro Color 42
228 –231
Macro Color 43
232 –236
Macro Color 44
237 –241
Macro Color 45
242 –246
Macro Color 46
247 –251
Macro Color 47
252 - 255
Macro Color 48
3
Red
000 –255
Red Dimmer
4
Green
000 –255
Green Dimmer
5
Blue
000 –255
Blue Dimmer
6
White
000 –255
White Dimmer
7
Strobe
000 –009
No strobe
010 –255
Strobe from slow to fast ( 1Hz-25Hz)
8
Pan
000 –255
Pan Moving 0-630°
9
Pan Fine
000 –255
Speed fine moving
10
Tilt
000 –255
Tilt Moving 0-270°
11
Tilt Fine
000 –255
Speed fine moving
12
Function
Over 5 seconds on each value
000 –127
Unused
128 –255
Auto sound function
9 Channel settings:
DMX 9 Channel
DMX
Description
1
Pan
000 –255
Pan Moving 0-630°
2
Tilt
000 –255
Tilt Moving 0-270°
3
Pan Fine
000 –255
Pan fine moving
4
Tilt Fine
000 –255
Tilt fine moving
5
Dimmer/Strobe
000 –200
Dimmer 0-100%
201 –247
Strobe slow-fast
248 –255
Full on
6
Red
000 –255
Red Dimmer
7
Green
000 –255
Green Dimmer
8
Blue
000 –255
Blue Dimmer
9
White
000 –255
White Dimmer

- 10 -
MAINTENANCE
The unit should be cleaned periodically to ensure the optimum performance, the smudginess can
decrease the life of light and the output of light is affected by the dust which can make the machine
overheating. In general, make the maintenance at least two times a month. Be sure to power off the
unit before cleaning .
Do not clean until the unit recovers normal temperature since high temperature for using, use the lens
tissue or soft cotton cloth with alcohol to wipe gently.
Cleaning frequency depends on the environment in which the fixture operates, damp, smoky or dirty
surrounding can cause greater accumulation of dirt on the optics. Never rub or press strongly on the
panel.
Specification
CE (!) : Explanation - This Class-I 2.4GHz equipment can be placed on the market without restrictions.
Please consult the authorities of your own country for detailed information regarding the licensing
regime! In the following countries the regulative frequencies are :
NL: 2245-2495.0 MHz, D: 2384.0-2483.5 MHz,
B: 2400-2483.5 MHz, F: 2465.0-2475.0 MHz,
I: 2215-2500.0 MHz, E: 2304.5-2480.5 MHz,
RUS: 2200-2500.0 MHz, CZ: 2200.0-2500.0 MHz,
POR: 2483.5 MHz
Pan movement:
630°
Tilt movement:
270°
Beam angle:
10°
Light intensity:
20000 lux @ 2m
No. of LEDs:
7x 15W Quad LEDs
DMX channels:
9 or 12
Connector:
3-pin XLR
Power Supply:
100-240Vac / 50Hz
Dimensions:
273 x 167 x 331mm
Weight:
4.5kg

- 11 -
CE & R&TTE Declaration of Conformity
Importer: TRONIOS BV
Bedrijvenpark Twente 415
7602 KM - ALMELO
Tel : [phone]
Fax : [phone]
The Netherlands
Product number: 150.527
Product Description: MHL-715WiSpot 7x 15W QUAD DMX 2.4Ghz
Regulatory Requirement: EN 60598-1/-2-17
EN 55015
EN 61547
EN 61000-3-2/-3-3
EN 300 440-1/-2
The product meets the requirements stated in Directives 2006/95 and 2004/108/EC
and 1999/5/EC and conforms to the above mentioned Declarations.
Almelo,
13-12-2012
Signed:
P. Feldman

- 12 -

- 13 -
Specifications and design are subject to change without prior notice..
www.tronios.com
Copyright © 2013 by TRONIOS the Netherlands