Beamz PAR64 DMX 177LED 10mm User manual

P
PP
PA
AA
AR
RR
R64 DMX 177
64 DMX 17764 DMX 177
64 DMX 177LED 10mm
LED 10mmLED 10mm
LED 10mm
INSTRUCTION MANUAL

ENGLISH
Congratulations to the purchase of this Beamz light effect. Please read this manual thoroughly prior to using the unit in
order to benefit fully from all features.
Read the manual prior to using the unit. Follow the instructions in order not to invalidate the warranty. Take all precautions
to avoid fire and/or electrical shock. Repairs must only be carried out by a qualified technician in order to avoid electrical
shock. Keep the manual for future reference.
- Prior to using the unit, please ask advice from a
specialist.When the unit is switched on for the first time,
some smell may occur. This is normal and will
disappear after a while .
- The unit contains voltage carrying parts. Therefore do
NOT open the housing.
- Do not place metal objects or pour liquids into the unit
This may cause electrical shock and malfunction.
- Do not place the unit near heat sources such as
radiators, etc. Do not place the unit on a vibrating
surface. Do not cover the ventilation holes.
- The unit is not suitable for continuous use.
- Be careful with the mains lead and do not damage it. A
faulty or damaged mains lead can cause electrical
shock and malfunction.
- When unplugging the unit from a mains outlet, always
pull the plug, never the lead.
- Do not plug or unplug the unit with wet hands.
- If the plug and/or the mains lead are damaged, they
need to be replaced by a qualified technician.
- If the unit is damaged to such an extent that internal
parts are visible, do NOT plug the unit into a mains
outlet and DO NOT switch the unit on. Contact your
dealer. Do NOT connect the unit to a rheostat or
dimmer.
- To avoid fire and shock hazard, do not expose the unit
to rain and moisture.
- All repairs should be carried out by a qualified
technician only.
- Connect the unit to an earthed mains outlet
(220-240Vac/50Hz) protected by a 10-16A fuse.
- During a thunderstorm or if the unit will not be used for
a longer period of time, unplug it from the mains. The
rule is: Unplug it from the mains when not in use.
- If the unit has not been used for a longer period of time,
condensation may occur. Let the unit reach room
temperature before you switch it on. Never use the unit
in humid rooms or outdoors.
- During operation, the housing becomes very hot. Do
not touch it during operation and immediately after.
- To prevent accidents in companies, you must follow
the applicable guide lines and follow the instructions.
- Secure the unit with an extra safety chain if the unit is
ceiling mount. Use a truss system with clamps. Make
sure nobody stands in the mounting area. Mount the
effect at least 50cm away from inflammable material
and leave at least 1 meter space on every side to
ensure sufficient cooling.
- This unit contains high intensity LEDs. Do not look into
the LED light to prevent damage to your eyes.
- Do not repeatedly switch the fixture on and off. This
shortens the life time.
- Keep the unit out of the reach of children. Do not leave
the unit unattended.
- Do not use cleaning sprays to clean switches. The
residues of these sprays cause deposits of dust and
grease. In case of malfunction, always seek advice
from a specialist.
- Only operate the unit with clean hands.
- Do not force the controls.
- If the unit has fallen, always have it checked by a
qualified technician before you switch the unit on
again.
- Do not use chemicals to clean the unit. They damage
the varnish. Only clean the unit with a dry cloth.
- Keep away from electronic equipment that may cause
interference.
- Only use original spares for repairs, otherwise serious
damage and/or dangerous radiation may occur.
- Switch the unit off prior to unplugging it from the mains
and/or other equipment. Unplug all leads and cables
prior to moving the unit.
- Make sure that the mains lead cannot be damaged
when people walk on it. Check the mains lead before
every use for damages and faults!
- The mains voltage is 220-240Vac/50Hz. Check if
power outlet match. If you travel, make sure that the
mains voltage of the country is suitable for this unit.
- Keep the original packing material so that you can
transport the unit in safe conditions.
This mark attracts the attention of the user to high voltages that are present inside the housing and that are of
sufficient magnitude to cause a shock hazard.
This mark attracts the attention of the user to important instructions that are contained in the manual and that he
should read and adhere to.
DO NOT LOOK DIRECTLY INTO THE LENS. This can damage your eyes. Persons who are subject to epileptic
attacks should be aware of the effects that this light effect may have on them.
The unit has been certified CE. It is prohibited to make any changes to the unit. They would invalidate the CE certificate
and their guarantee!
NOTE: To make sure that the unit will function normally, it must be used in rooms with a temperature between 5°C/41°F
and 35°C/95°F.

DMX settings
Dipswitch Code Set
Function
1 2 3 4 5 6 7 8 9 10
Sound
1 0 0 0 0 0 0 1 0 0
DMX512
SET DMXADDRESS FOR DMX MODE 1
Channel 1
Blue LED
Channel 2
Green LED
Channel 3
Red LED
Channel 4
Strobe
Channel 5
Change Speed
Technical specification
Light intensity .......Red 8000mcd, Green 20000mcd, Blue 6000mcd
DMX channels.................................................................................5
Power Supply.......................................................220-240Vac, 50Hz
Consumption..............................................................................25W
Beam angle..................................................................................15°
Weight....................................................................................1.95kg
Dimensions................................................................ø210 x 270mm
Electric products must not be put into household waste. Please bring them to a recycling
centre. Ask your local authorities or your dealer about the way to proceed.
The specifications are typical. The actual values can slightly change from one unit to the other.
Specifications can be changed without prior notice.
WARRANTY CONDITIONS
The date the product leaves the importer is considered to be the date the warranty begins. The law
obliges the retailer to offer a guarantee to the end-user. Ask your retailer for the warranty period.
Only companies approved by Tronios are allowed to work on the equipment.
During warranty period (defective) equipment must be returned to the dealer by pre-paid mail in the
original box.
For all service enquiries, refer to your local distributor, as he is best able to help you.