Beautural Fabric Shaver User manual

1byone Products Inc.
1230 E Belmont Street, Ontario, CA, USA 91761
Customer Service: [phone]
www.1byonebros.com
Made in China
Fabric Shaver
Instruction Manual

1
Introduction
Thank you for purchasing BEAUTURAL Fabric Shaver.
This instruction manual contains important information
about safety, usage, and disposal. Use the product as
described and keep this manual for future reference. If
you sell this shaver or pass it on, also give this manual to
the new owner.
Appliance Description
5
6
3
4
1
2
7
8
1. ON/OFF/Speed Switch
2. Battery Compartment Cover
3. Fluff Collector
4. Cutting Blades
5. Shaver Foil
6. Adjustable Spacer
7. Cleaning Brush
8. Protection Cap

2 3
Safety Instructions
Intended Use
This product is only authorized for domestic use and not
for commercial or industrial purposes. It is only intended
for applications described in these instructions.
Safety Information
• Children should not use, clean, or perform maintenance
on the fabric shaver without adult supervision.
• Do not expose or submerge the shaver in water. Do
not use the fabric shaver on moist fabrics.
• Make sure no foreign objects penetrate the shaver.
• Do not attempt to open the shaver’s housing, except
the battery compartment to replace batteries and
shaver foil to clean cutting blades.
• Do not oil or grease the cutting blades! This will smear
your clothes.
• Please keep away from hair when using the shaver.
• Please turn off the shaver before removing the fluff
collector.
Battery Safety Instructions
EXPLOSION HAZARD!
Never recharge non-rechargeable batteries, short-circuit
and/or open batteries. This can cause them to overheat,
burn or burst. Never throw batteries into fire or water.
The batteries may explode.
• WARNING! Switch the appliance to the "0"
position before inserting the battery.
• Use only the battery type recommended for this
appliance.
• Insert the battery correctly into the battery
compartment, observing the correct polarity (+and-).
• Check battery regularly for signs of expiry.
• If you disregard these instructions and advice, the
battery may discharge beyond its minimum voltage,
thus increasing the chance of leakage. If the battery
leaks, remove it from the device immediately to
prevent the device from being damaged!
• Check regularly that the batteries are not leaking.
• Leaked or damaged batteries can cause chemical
burns if they come into contact with the skin; in such
cases you must wear suitable protective gloves.
• Remove battery if appliance is not used for long
periods.
• Alkaline batteries recommended. Never use alkaline
batteries and carbon batteries together.
• Never use new batteries and old batteries together.
• Do not use rechargeable batteries.
• An exhausted battery is to be removed from the
appliance.
• The supply terminals are not to be short-circuited.
• Always keep batteries out of the reach of infants
and young children to prevent them from being
swallowed. If swallowed, take immediate action and
contact medical authorities for help.

4 5
Included Items
1 x Fabric Shaver
1 x Protection Cap
2 x Replaceable Cutting Blades
1 x Cleaning Brush
1 x Storage Bag
1 x Instructional Manual
Before using the fabric shaver for the first time, check
the package contents to ensure all parts are free of
visible damage.
Handling and Operation
Inserting Batteries
Press the tabs on the battery compartment cover and
push down. Insert 2 AA batteries (not included), paying
attention to the polarity. Put the battery compartment
cover back on and the shaver will be ready for use.
Testing
• The fabric shaver can damage delicate fabrics and
very soft materials such as angora. Before removing
fluff, always test on a small area of the fabric that
is not publicly visible to confirm the speed level is
appropriate for the fabric.
• Turn the transparent adjustable spacer to the level
“Thick” and then push the On/Off/Speed Switch to
Speed Level 1. To test the most suitable speed for
your fabrics and avoid damaging the garment, it is
recommended to use Speed Level 1 first, then switch
up to Speed Level 2.
Shaving Off Fluff
1. Put the garment on a flat surface, such as an ironing
board. Make sure the surface has no wrinkles.
Otherwise, the garment may be damaged.
2. Turn the spacer to the desired level or remove it
completely (see the "Removing/Attaching the Spacer"
section of this manual).
• “Thick” is for large bobbles and coarse textiles; 5mm-
length distance from the cutting blades.
• “Thin” is for small lint/bobbles and fine textiles; 3mm-
length distance from the cutting blades.
• Removing the spacer is only for very fine lint; virtually
no spacing to the cutting blades.
3. Push the On/Off/Speed Switch to the required speed
level.
4. Guide the shaver foil lightly over the material. The fluff
and bobbles will be shaved off and collected in the
fluff collector.
5. To turn off the shaver, push the On/Off/Speed Switch
back to Speed Level 0.
Note:
• Empty the fluff collector regularly. The fluff collector
should never be more than 3/4 full. An overfilled
fluff collector will slow the cutting blades no matter
the amount of battery power left.

6 7
Removing/Attaching the Spacer
• To remove the spacer, hold the shaver with one hand,
grab the spacer, put your thumb on the edge of the
spacer, pull the spacer forward, and remove it.
Pull to open
Thick Thin
Regulator
• To attach the spacer, place it on the cutting head and
press it firmly. Make sure the two small tabs on the
spacer grip into the two recesses on the shaver.
Pull to open
Thick Thin
Regulator
• To protect the shaver foil, you should remove the
spacer and place the protective cap on the shaver foil
when not using the fabric shaver.
Replacing the Cutting Blades
1. To remove the cutting blades - Unscrew the shaver
foil, carefully grasp the cutting blades’edge and pull
them out, avoiding damage to the blades.
2. To attach the cutting blades - Grasp the cutting blades’
edge and firmly insert the cutting blades into shaver
body. Finally, screw the shaver foil back into place.
Warning: Keep the protective cap in place when
the shaver is not in use to prevent children from
accidentally injuring themselves.

8 9
Emptying the Fluff Collector
1) Pull the fluff collector a little way down and lift it off.
2) Empty the textile fluff.
3) Place the fluff collector back on the shaver.
Cleaning the Housing and Cutting Blades
1) Unscrew the shaver foil, spacer, and protective cap,
cleaning those parts with a slightly damp cloth.
2) Use the officially provided cleaning brush to remove
fluff and lint remnants from the cutting blades.
3) Screw the shaver foil back on when all parts are
completely dry.
4) Place the spacer back on the shaver.
Note:
• Never use any corrosive liquids. These may damage
the surface of the shaver.
• Be careful when handling the cutting blades. They
are very sharp and can easily be damaged.
Specifications
Model: 1-MR02NA01, LT-142
Power Supply: 2 x 1.5V type AA batteries
Voltage: 3V
The appliance’s packaging is made from
environmentally friendly material and can be
disposed of at your local recycling plant.
Customer Service/Kundenservice
Service Clients/Atención al cliente/Assistenza Clienti
UNITED STATES
Phone: [phone]
(Mon-Fri 9:00am - 5:00pm PST)
Email: [e-mail]
CANADA Email: [e-mail]
UNITED KINGDOM
Phone: [phone]
(Mon-Fri 9:00am - 6:00pm UTC)
Email: [email protected]
GERMANY/FRANCE
ITALY/SPAIN Email: [e-mail]
BRAND OWNER
1byone Products Inc.
1230 E Belmont Street, Ontario, CA, USA 91761
Customer Service: [phone]
www.1byonebros.com