BEC MX-200 User manual

Quick Install Guide
1
2
3
Attach the Antennas
Remove the plastic dust
caps from the antenna
connectors.
Screw the antennas until
fully attached to the female
connectors of the Cellular
and/or GPS Modules.
LAN - Green: Connected to a Gigabit (1000Mbps) device.
Orange: Connected to a 10/100Mbps device
Blinking: Data being transmitted / received
LTE Signal Strength –Green: RSSI > -69dBm. Excellent
Green / Fast Flashing: -69 > RSSI > -81dBm. Good.
Red / Fast Flashing: -81 > RSSI > -99dBm. Fair.
Red / Slow Flashing: -99dBm > RSSI. Poor
Red: No Cellular signal. Cellular module still in service
Off: No Cellular module or module failure
Internet - Green: IP traffic via WAN
Red: WAN IP request failed
Off: No WAN connection or in Bridge mode
Power - Green: System ready. Red: Boot failure
WHAT’S IN THE BOX
1 x BEC MX-200 M2M Router
1 x This Quick Install Guide
1 x CD containing the User Manual
1 x DIN Rail Mounting Kit
1 x Power Terminal Block 2-Pin 3.5mm
1 x Power Cable with 2-Pin Terminal Block
1 x DC Power Adaptor, 12V 1.2A
(Optional)
3G/4G Antennas
Active GPS Antenna
SETTING UP THE ROUTER
DEVICE OVERVIEW & LEDS
Insert the SIM card
Slide the SIM card (2FF)
with the mental contacts
(gold plate) facing down to
the SIM slot then push it
all the way in until you
hear the clicking sound.
Connect the Serial (RS-232)
Use a RS-232 (DB-9)
male serial adaptor to
connect with industrial
equipment –including
PLC, SCADA, Sensor,
Meters, and Motor.
3
4
5
5
1
2
3
4
Access to the MX-200 Web interface by entering http://192.168.1.254
in the address bar of the web browser.
Default Login Information: Username (admin) and Password (admin).
The Quick Start Wizard provides key steps to get the MX-200 on the
Internet.
Connect to the MX-200
1.1 Attach the power
cable with 2-pin terminal
block to the MX-200 and
plug in the supplied power
adaptor
Connect to Power Source
1.2 Attach the power
terminal block (TB) to the
MX-200 and connect the
wire leads of the power
supply cable to the TB plug.
The red wire (power/VCC)
should connect to the
positive terminal and black
wire to the ground (GND) of
the power supply.
Input voltage range is from
9-56V

ATTACHING TO A DIN RAIL REMOVING FROM A DIN RAIL
MOUNTING POSITIONS
Remove MX-200 from a DIN rail.
1-2. Push down the MX-200 to free the bottom of the clip
from the DIN rail.
3. Unhook the top of the clip and pull the MX-200
away from the DIN rail
DIN RAIL MOUNTING
DIN RAIL MOUNTING OPTIONS
KIT CONTAINS: DIN Rail Clip and Six (6) Clip Mounting Screws
The DIN Rail mounting kit is designed to securely attach and clip the MX-200 onto a TS35 or standard 35mm top hat (EN
500022/BS 5584) DIN rail in the horizontal position.
Two (2) mounting locations to mount the DIN rail clip on the surface of MX-200, back or rear side.
Please follow the steps to complete DIN rail mounting installation.
1
Clip and secure the MX-200 onto a DIN rail.
1. Hook the top of the clip onto the top edge of the DIN
rail. Make sure the clip is firmly against the rail.
2. Push down the bottom of the MX-200 to snap it onto
the lower edge of the DIN rail.
3. The MX-200 is now mounted on the DIN rail.
Attach and fasten the DIN rail clip (known as clip)
to the back or rear side of the MX-200 using two (2) clip
mounting screws included in this mounting kit.
1.MX-200 2.DIN rail clip 3.Mounting Screws
I
1
II
Install clip in either vertical or horizontal position
I
II
I
SUPPORT: Visit us at www.bectechnologies.net.