BEC RidgeWave 7000 R26-W User manual

Quick Start Guide
BEC 7000 R26-W
Gigabit LTE Outdoor Router
with Hotspot

7000 R26-W Gigabit LTE Outdoor Router with Hotspot
1
Package Contents
BEC Outdoor Router x 1
M25 Cable Gland x 2
2.4G Wi-Fi Antennas x 2
This Quick Guide x 1
Outdoor LAN Cable x 1
5G Wi-Fi Antennas x 4
Gigabit PoE Injector x 1
Grounding Wire x 1
The Mounting Kit x 1
PLEASE READ THE QUICK START GUIDE AND FOLLOW THE
STEPS CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU
INSTALL THE DEVICE PROPERLY AND AVOID IMPROPER USAGE.
IF YOU NEED MORE INFORMATION
ON THIS SOFTWARE
CONFIGURATION, PLEASE REFER TO THE USER MANUAL.

INDUSTRIAL SIM IS RECOMMEND! (BEC 7000 R26-W)

Quick Start Guide
2
Hardware Overview (BEC 7000 R26-W)
PORT & LED MEANING
1
WIFI Antenna
Connectors
(2.4GHz)
Screw the supplied 2.4GHz antennas onto the antenna connectors on both sides.
2 RESET
After the device is powered on, press it 6 seconds or above: to restore to factory
default settings (this is used when you cannot login to the router, e.g. forgot your
password)
3 SIM Card Slot
Insert the mini SIM card (2FF) with the gold contact facing down.
Push the mini SIM card (2FF) inwards to eject it
* Power off the BEC 7000 R26-W before inserting or removing the SIM card(s)
4 2.4GHz WIFI LED
Green Wireless connection established
Blinking Data being transmitted / received
5 5GHz WIFI LED
Green Wireless connection established
Blinking Data being transmitted / received
6
8
9
10
1
1
5
7
11
11
11
11
2
3
4

7000 R26-W Gigabit LTE Outdoor Router with Hotspot
3
PORT & LED MEANING
6
LTE LED
(Received
Signal Strength
Indicator)
Green RSSI greater than -69 dBm. Excellent signal condition
Green Flashing Quickly RSSI from -81 to -69 dBm. Good signal condition
Orange Flashing Quickly RSSI from -99 to -81 dBm. Fair signal condition
Orange Flashing Slowly RSSI less than -99 dBm. Poor signal condition
Orange No signal and the 4G LTE module is in service
Off No LTE module or LTE module fails
7 Power LED
Green System is up and ready
Red Boot failure
8 Internet LED
Green IP connected; WAN connection is ready
Red IP request failed
Off Either in bridged mode or WAN connection is not available
9
Gb Ethernet
WAN
Use an outdoor Ethernet cable to connect to an internet device.
Note: The Ethernet WAN port is a configurable LAN/WAN port, which automatically becomes an
Ethernet WAN port when the internet interface is being configured in the GUI.
Green Transmission speed is at Gigabit speed (1000Mbps)
Orange Transmission speed is at 10/100Mbps
Blinking Data being transmitted/received
10
Gb Ethernet
LAN/PoE
LAN & PoE interface. Connect to the supplied 802.3at Gb PoE injector to provide
power & data
Green Transmission speed is at Gigabit speed (1000Mbps)
Orange Transmission speed is at 10/100Mbps
Blinking Data being transmitted/received
11
WIFI Antenna
Connectors
(5GHz)
Screw the supplied Wi-Fi antennas onto those 4 antenna connectors.

Quick Start Guide
4
Mounting Kit Installation
Mounting Kit includes:
1. Articulation Pole x 1
2. T-formed Bracket x 1
3. M8x40 Screw Bolt x 1
4. M8 Nut x 1
5. M8 Washer x 1
6. M6 Washer x 4
7. M8 Spring Washer x 1
8. M6 Spring Washer x 4
9. M6x16 Screw x 4
For Wall Mount Installation, you will
need:
10. Wood Screw x 4
11. Wood / Gyprock x 4
For Pole Mount Installation, you
will need:
12. W-Bar x 1
13. Stainless Hose Clamp x 2
14. M6 x 60 Screw Bolt x 2
15. M6 Washer x 2
16. Spring Washer x 2
T-form Bracket x 1
Articulation Pole x 1
M8x40 Screw Bolt x 1
Wood Screw x 4
Wood / Gyprock Plug x 4
Spring Washer M6 x 2
M6 Washer x 2
M6 x 16 Screw x 4
M8 Nut x 1
Spring Washer M8 x 1
Spring Washer M6 x 4
M8 Washer x 1
M6 Washer x 4
M6 x 60 Screw Bolt x 2
W-Bar x 1
Stainless Hose Clamp 1”~3” x 2

7000 R26-W Gigabit LTE Outdoor Router with Hotspot
5
1. Attach the Articulation Pole to the Enclosure
Attach the articulation pole to the back of the BEC 7000 R26-W ODU enclosure using the
supplied M6 screws, M6 spring washers and M6x16 screws which are included in the
mounting kit.
Tool Advice :
Use #10 HEX. Wrench to
tighten or loosen the
bolt(s).
1
2
3
M6 Washer
M6 Spring Washer
M6x16 Screw

Quick Start Guide
6
Note: The flexible mounting kit can be adjusted in multiple angles to align with the base station
for higher efficiency.
45∘
45
∘
45
∘
45∘

7000 R26-W Gigabit LTE Outdoor Router with Hotspot
7
2. Wall or Pole Mount Installation
Mounting on Wall
Fix the T-formed Bracket to the wall by using wood screws and Gyprock plugs.
Mounting on a Pole between 1.5” to 2” (38.1~50.8mm)
Attach the T-formed Bracket and the W-bar to the pole then use M6x60 bolts, M6 spring
washersand M6 washersto fix the mounting kit onto the pole.
T-formed Bracket
Wood Screw
Wood / Gyprock Plug
1
2
3
1
3
2
M6x60 Screw Bolts
M6 Spring Washer
M6 Washer
W-bar
1
2
3
4
(a
(b)
(a) The accept pole diameter is
from 1.5” to 2”. If the diameter is
larger than 2”, it can cause a
failure fast. If diameter is smaller
than 1.5”, the clamping force
might be insufficient in holding
the device to the pole.
(b) To minimize bolts
crosstalk, the bolt should
gradually increase the bolt
load on both sides.

Quick Start Guide
8
Mounting on a Pole between 1” to 3” (25.4~76.2mm)
1.
3. Attach the BEC 7000 R26-W Enclosure to the Pole
Attach the articulation pole (the BEC 7000 R26-W ODU enclosure) to the T-formed bracket
using the supplied M8 nut, M8 spring washer, M8 washer and M8x40 screw bolts.
Fix the T-formed Bracket to the pole by using the
supplied stainless hose clamps. Use a flat-head
screwdriver to turn the head of the screw
clockwise to tighten it.
Use the stainless hose clamps
through the T-formed Bracket.
Assembled
3
M8 Washer
4
M8 Nut
2
M8 Spring Washer
1
M8x40 Screw Bolts