BEC MX-1000 User manual

M2M
Model: MX-1000
Quick Install Guide
WHAT’S IN THE BOX
SETTING UP THE ROUTER
1 x BEC MX-1000 M2M Router
1 x This Quick Install Guide
1 x CD containing the User Manual
1 x Mounting Bracket
1 x MiniFIT to DC Jack Power Cable
2 x Wi-Fi Antennas
5 x Red Dust Caps
DC Power Adapter
3G/4G Antennas
Active GPS Antenna
Vehicle Power Cable
Ethernet (RJ-45) Cable
(Optional Accessories)
1Insert the SIM Card
Note: Power o the MX-1000 before inserting/removing the SIM
WIFI
WIFI ON/OFF
RESET
WIFI
MINI
USB2
SIM2 SIM1
MINI
USB1
WIFI
WIFI
WIFI ON/OFF
RESET
WIFI
MINI
USB2
SIM2 SIM1
MINI
USB1
WIFI
Remove the SIM cover
then insert the SIM card(s)
(2FF) with the mental
contacts (gold plate) facing
up to the SIM slot(s) then
push it all the way in until
you hear the clicking sound. Replace the metal SIM cover
after inserting the SIMs.
2Attach the Wi-Fi Antennas
WIFI
WIFI ON/OFF
RESET
WIFI
MINI
USB2
SIM2 SIM1
MINI
USB1
WIFI
WAN1
MAIN
WIFI WIFI
WAN1
MAIN
WIFI WIFI
Note: Use the plastic red caps to cover unused antenna ports
Screw the 2 female
RP-SMA Wi-Fi antennas
until fully attached to the
Wi-Fi ports on MX-1000.
Do not over-torque the
antenna on the connector.
3Attach the LTE & GPS Antennas
Note: Use the plastic red caps to cover unused antenna ports
Screw the 2 male SMA
Cellular/or GPS antennas
until fully attached to the
Cellular and/or GPS
modules.
Connect to the MAIN port,
the primary cellular antenna
port to transmit and
receive signal, if decide to
use one LTE antenna.
Do not over-torque the antenna on the connector.
WAN1
MAIN
USB1 USB2
1 2 3 4
WAN2
AUX
WAN1
AUX
GPS WAN2
MAIN
POWER
POWER INTERNET
Gb ETH
GPS WAN1 WAN2
WAN1
MAIN
WAN2
MAIN
WAN1
MAIN
WAN2
AUX
WAN1
AUX
GPS WAN2
MAIN
WAN1
MAIN
WAN2
MAIN
WAN1
MAIN
WAN2
AUX
WAN1
AUX
GPS WAN2
MAIN
WAN1
MAIN
WAN2
MAIN
WAN1
MAIN
WAN2
AUX
WAN1
AUX
GPS WAN2
MAIN
5Connect to Power Source
Use the DC Power Adapter
Attach the 4-pin MiniFIT to
DC Jack Power Cable to the
MX-1000 then plug in the
DC power adapter,
15VDC 1.6A.
Use Vehicle Electrical System (Power & Ignition Sensing)
Attach the Vehicle hardwire power
cable to the MX-1000 and connect
the wire leads of the power cable
to vehicle’s electrical system.
BLACK Wire (PIN 1 & 2):
Ground (GND). Use one
of the BLACK wires for
a neutral or ground
connection
WHITE Wire (PIN 3): ACC/ON for Ignition Input wire need to be
connecting into vehicle accessory wire.
RED Wire (PIN 4): VCC/OFF Voltage wire to the battery.
DC power range from 0V to 56V.
Battery
POWER
GND Ignition Switch
Fuse
ACC
VCC
MINI
USB2 MINI USB1
Connect to Mini USB Ports
Note: Need to install a special driver before connecting the device
Connect to Mini USB port(s)
for direct connection to the
Cellular module(s) for
management – debug,
change firmware, and
configuration.
6Access to the MX-1000
Access to the MX-1000 Web interface by entering
http://192.168.1.254 in the address bar of the web browser.
Default Login Information: Username (admin) and Password
(admin).
The Quick Start Wizard provides key steps to connect the
MX-1000 to the Internet.
4
PIN
1
2
3
4
Ground
Ground
ACC
VCC
Black
Black
White
Red
-
-
Input
10~56VDC
Definition Details Wire color
4
21
3
POWER

Gigabit RJ-45
Ethernet LAN Port
Gigabit RJ-45
Ethernet LAN/WAN Port
1POWER - Green: System ready
Red: Boot failure
2INTERNET - Green: IP traffic via WAN
Red: WAN IP request failed
Off: No WAN Connection or in Bridge Mode
5WAN 1/2 -
(Cellular
Signal
Strength
Indicator)
3USB 1/2 - Green: Connected with an external storage device
4GPS - Green: GPS is active
Green: RSSI greater than -69 dBm. Excellent signal condition
Green flashing quickly: RSSI from -81 to -69 dBm. Good signal condition
Red flashing quickly: RSSI less than -99 dBm. Poor signal condition
Red flashing slowly: RSSI less than -99 dBm. Poor signal condition
Red: No signal and the 4G LTE module is in service
Off: No LTE module or LTE module fails
6GIGABIT ETHERNET (Gb ETH) -
(LAN 1 - 4)
Green: Transmission speed is at Gigabit speed (1000Mbps)
Orange: Transmission speed is at 10/100Mbps
Blinking: Data being transmitted/received
Green: Wireless connection established
Blinking: Data being transmitted / received
7WI-FI -
USB 2.0 Host Ports
(External Storage)
WAN1
MAIN
USB1 USB2
1 2 3 4
WAN2
AUX
WAN1
AUX
GPS WAN2
MAIN
POWER
POWER INTERNET
Gb ETH
GPS WAN1 WAN2
LTE #1 (Main Antenna)
SMA Female Connector
GPS Antenna
SMA Female Connector
LTE #2 (Auxiliary Antenna)
SMA Female Connector
LTE #1 (Auxiliary Antenna)
SMA Female Connector
LTE #2 (Main Antenna)
SMA Female Connector
4-pin Power/Ignition Connector
(Input power 10-56V DC range)
123 4 5
6
WIFI
WIFI ON/OFF
RESET
WIFI
MINI
USB2
SIM2 SIM1
MINI
USB1
WIFI
Wi-Fi Female RP-SMA
Antenna Connector
SIM Card Slots
(Dual SIM Dual Module)
MINI USB
(LTE Module Management)
Reset
Wi-Fi On/Off
& WPS
7
DEVICE OVERVIEW & LEDS
Use the DC Power Adapter
Attach the 4-pin MiniFIT to
DC Jack Power Cable to the
MX-1000 then plug in the
DC power adapter,
15VDC 1.6A.

v1.00
MOUNTING THE ROUTER
MOUNTING BRACKET CONTAINS: Bracket plate and Ten (10) M4 Machine Screws
The Bracket plate is designed to securely attach and mount the MX-1000 on any flat surface – including desktop, table,
chassis, etc.
Attach the fasten the Mounting Bracket (known as bracket
plate) to the back or front of the MX-1000 using four (4) M4
machine screws included in the package.
1. MX-1000 2. Mounting Bracket 3. Mounting Screws
WAN1
MAIN
USB1 USB2
1 2 3 4
WAN2
AUX
WAN1
AUX
GPS WAN2
MAIN
POWER
POWER INTERNET
Gb ETH
GPS WAN1 WAN2
1
2
3
3
3
3
Side Views
Mount the MX-1000 to a flat surface by using four (4) self-drill-
ing screws through the bracket plate holes.
Note: Self-drilling screws are not provided
1. Bracket Holes
POLICE
1
1
1
1
20mm
4.5mm