Becker BKRCD-HF User manual

Courtesy of: DiscountCarStereo.com
Serving the internet community since 1995
For illustration purposes only
BKRCD-HF
Hands-Free,musicstreaminginstallationguideforBeckerradioswithCDchanger
Created June 30, 2016
Revised: February 4, 2020

Introduction:
Safety comes first when you’re on the road, so having an intuitive and easy to
use Bluetooth kit is essential to reducing driver distraction. The BKRCD-HF works
with virtually all Bluetooth enabled phones and sounds great whether using it for
mobile conversations, streaming music or listening to the CD Changer via the
“CD” input. One button with built-in mic conveniently installed on the dash is used
to launch Voice Recognition application (Siri, Google Now, Assistant etc.), initiate
phone calls, launch applications and listen to the CD changer. Keep the vehicle,
radio and CD changer while enjoying Bluetooth features only available on
newer cars. Note: A working CD changer is required and at least one disc must
be loaded for this module will not work as described.
Installation:
Most Becker radios are coded and will not operate
without the code. Do not proceed to step 4 if radio code
is not available otherwise radio will not operate upon
reconnection.
Remove radio from the dashboard to gain access to the connectors.
Special removal tools (See Fig. 1) are required to remove applicable Becker
radios (except PCM1)
Fig. 1
Radio removal Tools
1. Slide tools into slots on radio. (Straight edge facing away). Withdraw
radio by pulling outwards. To release keys simply press retaining
springs. See Fig. 2.
For a more detailed radio removal process, click here.
Fig. 2
2. Disconnect blue plug from C-3 chamber from radio (See Fig. 3) (pinch
blue tab to release)
Fig. 3
Radio Connectors
3. Connect blue plug removed from radio in step 2 to audio harness black
connector (See Fig. 4)

Fig. 4
audio harness
4. Connect audio harness blue plug (See Fig. 4) to radio C-3 chamber vacated
in step 2.
5. Disconnect 8-pin power plug from radio (chamber “A”)(See Fig. 3)
6. Connect 8-pin power plug (from step 5) to power harness matting 8-pin
connector (See Fig. 5)
Fig. 5
Power harness
7. Connect power harness 8-pin plug (See Fig. 5) to radio 8-pin connector
(chamber “A”) vacated in step 5.
8. Connect installation harness 3.5mm right angled (See Fig. 4) to module
pigtail jack (See Fig. 6)
Fig. 6
Module
9. Connect installation harness 3.5mm straight plug (See Fig. 4) to
Module “CD”input jack (See Fig. 7)
Fig. 7
Audio output jack
10. Connect control button/microphone plug (See Fig. 8) to module “MIC”
jack (See Fig. 6)
Fig. 8
Control button/Microphone
11. Consider where to install control/mic button. Keep in mind the control
button must be within reach and facing driver for voice commands and

phone dialog (microphone/control cable is 6ft. long). We recommend
completing the rest of the install prior to securing the
control/mic button to the dash. Once you decide on a location simply
remove tape backing from control /mic button
Make sure they are no ventilation duct is pointed towards the mic.
It is best to mount button facing driver
See Optional Microphone/control button installation kit at the end of
this guide.
Bluetooth Module has a built-in USB Charging port (See Fig. 11) should you decide
to use it; we suggest one of 2 installation options:
A. Flush to dash/panel which requires a ¾” hole in the dash
B. Flush with Support bracket (use this option to mount USB terminal
wherever your installation demands without drilling)
A. Flush to Dash or Panel (requires drilling)
1. Drill a ¾” hole in the dash or panel using a step drill bit or equivalent
(See Fig. 9)
Fig. 9
Step drill bit
2. Insert USB male terminal (See Fig. 10) through the ¾” hole created in
step 1 and connect to Module (See Fig. 11)
Fig. 10
Flush mount 3 ft. USB cable
Fig. 11
Module USB port
3. Push USB head (See Fig. 12) until it snaps in place and flush with
mounting surface (See Fig. 13)

Fig. 12
Flush mount USB Terminal
Fig. 13
Flush mounted to dash
4. Tuck and secure any extra wire from moving parts and test operation
(See Enabling the AUX section below)
B. USB with Bracket Mount (No drilling)
1. Locate a flat surface at location of choice to mount USB support
bracket (See Fig. 14) to surface using adhesive/tape or screws.
Fig. 14
USB mounting bracket
2. Insert USB male terminal through hole in bracket (See Fig. 15) and
connect to Module (See Fig. 11)
Fig. 15
3. Push USB head until it snaps in place and flush (See Fig. 16)
Fig. 16
4. Tuck and secure any extra wire away from moving parts and test operation
( See Bluetooth Pairing and Connection )
The radio cavity in most vehicles may lack extra room
needed to fit aftermarket equipment and because of that
you will have to be creative when fitting this part. Extra
length cables are provided to allow for this flexibility
Secure module and proceed to section next section.

Bluetooth Pairing and Connection
After initial pairing, the BKRCD-HF will automatically reconnect with the paired
phone upon entering the vehicle.
1. Turn the vehicle ignition to “ON”.
2. The Red LED inside module will begin to flash
3. Access your Smartphone Bluetooth menu settings, and search (scan)
for devices.
4. Select the G2 and click “Connect”
Note: Supports multiple phones but connects to only one phone at a time.
Warning! Caller ID and text display are not possible in CD Changer mode.
Operating Bluetooth device is by pressing control button and your Voice
Recognition application. Use the Becker radio volume button to control playback
level.
Bluetooth Operation
1. Set the radio to CD changer mode
2. Adjust the radio volume
Music Commands
To
Proceed this way
Pause a Song
Press and release button
Resume Play
Press and release button
Skip to next song
Press button twice
Skip to Previous Song
Press button 3 times
Activate CD Changer Playback*
Press button 4 times
Activate Voice Control
Press/hold button for 2 seconds
Switch out of CD Changer Mode
Press and release button
Phone Commands
To
Proceed this way
Answer call
Press and release button
End call
Press and release button
Reject incoming call
Press button twice (call goes to VM)
Cancel outgoing call
Press button twice
Activate Voice Control
Press/hold button for 2 seconds
Notes:
1. If playback is distorted, adjust volume on Bluetooth device.
2. To reset Module press and Hold button for 5 seconds (this will not
un-pair phone or erase stored phones)
3. On incoming calls, ring tone will play on car speakers
4. Bluetooth range is approximately 30 ft. make sure device is within
range of receiver

5. Voice command compatible with Apple (Siri), Android (Google Now),
Blackberry (Assistant) etc.
6. At least one disc must remain in changer.
7. * Control button does not control CD changer functions. Use radio
control buttons for music selection and controls of the changer.
8. Upon ending call, audio streaming resumes playback, however to
resume CD playback, pressed control button 4 times.
If successful go ahead and Reinstall the Radio
Congratulations, you’ve just updated your vehicle to support new technology
while preserving the original radio and dash components.
Enjoy!
The BKRCD-HF is ideal for vehicles that include an analog CD Changer.
Vehicles that include digital system (e.g. CR23/24, PCM2+) as seen in Fig.
17 are not supported.
Fig. 17
Optional visor mount microphone kit
If you’ve installed or plan to install one of our “HF” (Hands-Free) kits, be aware
the microphone is built into the push-control button (See Fig. 18) which means it
must be mounted or installed in an area where it can be accessible to the driver
which may work in some vehicle but may not be optimum for issuing voice
commands or holding Bluetooth conversations in others.
Fig. 18
Due to many customer request, we are not offering the G2-HF kit which allows
for more installation flexibility by allowing control button to remain on the dash
or within drivers reach and separate clip-on type microphone which would
ideally mount to visor (See Fig. 19) from which driver can issue voice commands,
hold Bluetooth conversations while also keeping eyes on the road.
Package contents:
Microphone with visor clip on 10ft. cable x 1
Push-to-talk button (green) x 1
Splitter harness x 1

Fig. 19
Installation:
1. Use clip to Install microphone to visor or location of choice and route
cable down pillar, under dashboard toward Bluetooth module location
2. Connect microphone right angle plug (See Fig. 20) to splitter harness
“Mic input” jack (See Fig. 20) –indicated with arrow. (larger 3.5mm
jack)
Fig. 20
3. Connect push-to talk button (blue or green phone icon) to splitter
“Control button” jack as seen in Fig. 20 (smaller jack)
4. Connect splitter harness 4-pin male plug to module “Mic” input (blue)
as seen in Fig. 21
Fig. 21
Warning: If clicking sound or no audio during playback, reverse connections
to splitter harness.
Please also note, it is possible to connect original control button (blue
phone symbol) or control button (green phone symbol) included in G2-HF kit
to splitter harness. When G2-HF kit is purchased along with Bluetooth
kit “HF”, the blue button control button is not included.

Frequent asked questions
1. Do I require a working CD changer for this adapter to work?
YES; CD changer is required and remain fully functional.
2. Does the BKRCD-HF work on all Becker radios?
NO; For Becker analog radios with analog CD changers. Will not work in
Digital systems (e.g. PCM2, CDR-23/24 etc.)
3. Can I control my Smartphone music from the radio buttons?
NO; you must continue to use Phone built-in controls or the control button
and/or voice commands to operate the device.
4. How to I reset Bluetooth Module?
Press and hold the control button for 5 seconds then release.
5. How can I listen to my CD changer?
Hit CD button on the radio, then press control button 4 times.
6. Where is the best place to install the control button/mic?
We found that having the control button/mic mounted higher on the dash worked
best, but final location should be left to user.
7. Will the stereo mute when I receive or make a phone call?
This system will not mute the stereo unless the radio is in “CD Changer” mode
(Bluetooth mode). If you are in Radio Mode (AM/FM) and a call comes in, the radio
will not mute. In addition, you must switch the radio to “CD Changer” (Bluetooth
Mode)
8. How to I pair a second phone to Bluetooth Module?
In order to pair another phone make sure no previously paired phone is connected.
Once the device is free, it is ready for pairing.
Disclaimer
• This product has no affiliation with Porsche, Becker or Apple
• We’re not liable for misuse of this product.
© 1995-Feb-20 Discount Car Stereo. All rights reserved. Information in this document is
subject to change without notice. Other products and companies referred to herein are
trademarks or registered trademarks of their respective companies or mark holders.