Becker Sequel 6002 Return Quick start guide

1
Placement and Maintenance
Sequel™ Home Office Furniture is designed for indoor use on level floors. Clean
glass with glass cleaner, and steel parts and wood veneer with a moist cloth. Your
Sequel™ Home Office Furniture is engineered for easy assembly. Carefully follow this
procedure to prevent any damage.
Do not use power tools for assembly of this product.
Step 1
Unpack and identify the parts listed below. The assembly workspace should be a non-
marring surface such as carpet. For missing hardware pieces, please contact BDI
Customer Service at [email protected]. For all other concerns, please
contact your BDI Retailer.
Sequel
6002 Re t u R n
assembly instRuctions
b d i u s a .c o m customeRseRvice@b d i u s a .c o m
Designed by Matthew Weatherly.
‘Sequel’ is a trademark of Becker Designed, Inc.
All rights reserved. ©2009 Becker Designed, Inc.
Made in Taiwan. 6002REV121409v5
G- 1/4-20 x 2 3/8” Screw x 6
H- 1/4-20 x 1/2” Screw x 16
F- 4mm Hex Wrench x 1
Component List
B- Top Glass x 1
D- Front Kick Panel x 1
C- Back Panel x 1
(optional)
L- Right Leg x 1
K- Left Leg x 1
M- Glides x 4
A - Frame Assembly x 1
E- Lower Horizontal Beam x 1
N- Upper Horizontal Beam x 1
6001
6002
6005
5
6
6
6006
6
6
6007
7
6

2
assembly instRuctions
b d i u s a .c o m c u s t o m e R s e R v i c e @b d i u s a .c o m
Step 1
Install Glides (M) to the bottom of Left Leg (K) and Right Leg (L).
M x 4
LK

3
assembly instRuctions
b d i u s a .c o m c u s t o m e R s e R v i c e @b d i u s a .c o m
L
A
H
H
Step 2
Attach Left Leg (K) to Frame Assembly (A) using Screw (H) and
Hex Wrench (F).
Step 3
Attach Right Leg (L) to Frame Assembly (A) using Screw
(H) and Hex Wrench (F).
K
A

4
assembly instRuctions
b d i u s a .c o m c u s t o m e R s e R v i c e @b d i u s a .c o m
Step 4
Attach Upper Horizontal Beam (N) to inside of Left and Right Leg
using Screw (H) and Hex Wrench (F).
N
H
H

5
assembly instRuctions
b d i u s a .c o m c u s t o m e R s e R v i c e @b d i u s a .c o m
Step 5
Attach Lower Horizontal Beam (E) to inside of Left and Right Leg
using Screw (H) and Hex Wrench (F).
2 Person Task
E
H
H

6
assembly instRuctions
b d i u s a .c o m c u s t o m e R s e R v i c e @b d i u s a .c o m
Step 6
With the help of another person, gently lower Assembly onto Top
Glass (B). Both parts will be placed upside down for the assembly
process and fasten into place using Screw (G) and Hex Wrench (F)
at all (7) fastener locations. DO NOT OVERTIGHTEN! With the help of
another person, turn return upright onto its base.
B
G
G
G
G
G
G
G
G
2 Person Task

7
assembly instRuctions
b d i u s a .c o m c u s t o m e R s e R v i c e @b d i u s a .c o m
Step 7
Place Sequel Return in desired location. Once all of the electrical wires are
routed, install Kick Panel (D) as shown above. The rear side of panel has
magnets that will hold the panel in place. Note: The Sequel Return is designed
to permit placement in front of an electrical outlet for easier wiring access.
Optional Step
If return is located in the middle of a room, the optional 6009 Back Panel (C)
is available for purchase to conceal wire management. Please contact BDI
Customer Service at [email protected] or 800-428-2881
D
C