BED BATH & Beyond FALCON WF306943 User manual

ASSEMBLY INSTRUCTIONS
FALCON EXTENSION TABLE
IMPORTANT NOTE:
PLACE ALL PARTS ON A CLEAN AND SMOOTH SURFACE SUCH AS A RUG OR
CARPET TO AVOID THE PARTS FROM BEING SCRATCHED.
BEFORE YOU BEGIN, KINDLY FOLLOW THE ASSEMBLY INSTRUCTIONS STEP
BY STEP.
DO NOT TIGHTEN ALL SCREWS AND BOLTS UNTIL THE TABLE IS FULLY SET-
UP.
-
-
-
01-02
WF306943

02-02
1
1
3
3
CARTON CONTENT:
2
x 1 x 1
x 4
TABLE HARDWARE LISTS
A
B
C
DALLEN KEY M5 X 25 X 75
JCBB SCREW M8 X 60MM
FLAT WASHER M8 X 18MM
SPRING WASHER M8 X 13.5MM
NO. DESCRIPTION SKETCH
8PCS
8PCS
8PCS
1PC
QTY
1
2
3
1PC
4PCS
1PCS
TABLE TOP
TABLE LEG
EXTENSION TOP
NO. DESCRIPTION
TABLE PART LISTS
QTY
SKETCH
ASSEMBLY COMPLETE!
(WITH EXTENSION LENGTH)
1
2
1
1
2
2
3
3
4
4
ABC
D
Unlock the 4 locks at the
bottom of the table
How to remove the Extension Top?
1. 2.
With the assistance of
another person, slide
each half of Table Top
outward in the opposite
direction to extend
table top slightly as
being shown.
3.
Lift up the Extension
Top (3)
4. COMPLETED
Attach the Table Leg (2) to the Table
Top (1) using screw (A), spring washer
(B) and flat washer (C). Tighten up
with allen key (D). Please ensure that
the table leg is being slot into the 4
blocks according to the same labelling
number for the leg and block.
STEP 1
With the assistance of
another person, slide
each half of Table Top
inward to close up the
gap at the center.
Locked the 4 locks at
the bottom of the
table
2
2
22
2
3
WF306943

ASSEMBLY INSTRUCTIONS
FALCON DINING CHAIR
IMPORTANT NOTE:
PLACE ALL PARTS ON A CLEAN AND SMOOTH SURFACE SUCH AS A RUG OR
CARPET TO AVOID THE PARTS FROM BEING SCRATCHED.
BEFORE YOU BEGIN, KINDLY FOLLOW THE ASSEMBLY INSTRUCTIONS STEP
BY STEP.
DO NOT TIGHTEN ALL SCREWS AND BOLTS UNTIL THE CHAIR IS FULLY SET-
UP.
-
-
-
01-03
WF306945

1
5
4
3
6
7
2
CARTON CONTENT:
13 4 5 6 7
2
x 4 x 4 x 4 x 4 x 4 x 8
x 4
CHAIR HARDWARE LISTS
CHAIR PART LISTS
A
B
C
D
E
F
G
1
2
3
4
5
6
7
16PCS
16PCS
8PCS
40PCS
40PCS
40PCS
1PC
4PCS
4PCS
4PCS
4PCS
4PCS
4PCS
8PCS ALLEN KEY M4 X 25 X 65
JCBC SCREW M6 X 70MMCHAIR BACK
JCBC SCREW M6 X 50MMFRONT LEG (R)
FRONT LEG (L)
BOX SEAT
FRONT STRETCHER
SIDE STRETCHER(L/R)
JCBC SCREW M6 X 35MM
FLAT WASHER M6 X 18MM
CHAIR SEAT
SCREW M4 X 32MM
SPRING WASHER M6 X 13.5MM
NO.NO. DESCRIPTIONDESCRIPTION SKETCH SKETCH QTYQTY
02-03
WF306945

STEP 4
Finally, attached the Chair Seat (5) to the
chair frame using screw (F)and drive it
with Phillip Screwdriver (not provided).
STEP 1
Place the Chair Back(1) on a flat & soft surface to prevent
scratches.
Attach the Box Seat (4) to the Chair Back(1).
Secure from the center using flat washer(E), spring
washer(D) & JCBC screw M6 x 35mm(C).
Secure the 2 corners using flat washer(E), spring
washer(D) & JCBC screw M6 x 70mm(A).Tighten up with
Allen Key(G).
PLEASE DO NOT FULLY TIGHTEN THE SCREWS UNTIL
FINAL STEPS.
STEP 3
Align the front stretcher (6) & side
stretcher (7) at proper position and
tighten with screw (F) and
drive it with Phillip Screwdriver (not
provided). Then make sure all legs are
level. Once level , tighten all the screws
securely at this stage.
F
STEP 2
Attach Front Legs(2 & 3) to
the assembled chair back (1)
with box seat(4) by using
flat washer(E), spring
washer(D) and JCBC screw
M6 x50mm(B). Only
SLIGHTLY by Allen
Key(G) to ensure they are
not falls out.
tighten B
D
E
G
R
FR
FL
L
PHILLIPS
SCREWDRIVER
03-03
G
A
D
E
D
E
C
4
14
1
2
3
76
F
PHILLIPS
SCREWDRIVER
5
ASSEMBLY COMPLETE!